New uhso(4) device: Globetrotter HSUPA Modem Option N.V.

Fri Feb 18 03:36:56 UTC 2011

On Thu, Feb 17, 2011 at 6:58 PM, Brandon Gooch
<jamesbrandongooch at gmail.com> wrote:
> I've recently got my hands on an Option N.V. Globetrotter HSUPA Modem,
> rev 2.00/0.00, addr 2.
>
> Here's the usbconfig dump:
>
> ugen6.2: <Globetrotter HSUPA Modem Option N.V.> at usbus6, cfg=0
> md=HOST spd=HIGH (480Mbps) pwr=ON
>
>  bLength = 0x0012
>  bDescriptorType = 0x0001
>  bcdUSB = 0x0200
>  bDeviceClass = 0x00ff
>  bDeviceSubClass = 0x00ff
>  bDeviceProtocol = 0x00ff
>  bMaxPacketSize0 = 0x0040
>  idVendor = 0x0af0
>  idProduct = 0x7a05
>  bcdDevice = 0x0000
>  iManufacturer = 0x0002  <Option N.V.>
>  iProduct = 0x0001  <Option Configuration>
>  iSerialNumber = 0x0000  <no string>
>  bNumConfigurations = 0x0001
>
> After adding the product to sys/dev/usb/usbdevs:
>
> product OPTION GTHSUPA_2        0x7a05  Globetrotter HSUPA
>
> and  sys/dev/usb/net/uhso.c:
>
> UHSO_DEV(OPTION, GTHSUPA_2, UHSO_AUTO_IFACE),
>
> ...I got the driver to attach. Here's the message when I plug the device in:
>
> ugen6.2: <Option N.V.> at usbus6
> uhso0: <Diagnostic port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
> uhso0: "Diagnostic" port at cuaU0
> uhso1: <Application port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
> uhso1: "Application" port at cuaU1
> uhso2: <Control port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
> uhso2: "Control" port at cuaU2
> uhso0: bpf attached
> uhso3: <Network port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
> uhso4: <Modem port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
> uhso4: "Modem" port at cuaU3
> umass0: <Option N.V. Globetrotter HSUPA Modem, rev 2.00/0.00, addr 2> on usbus6
> umass0:  SCSI over Bulk-Only; quirks = 0x0000
> umass0:3:0:-1: Attached to scbus3
> (probe0:umass-sim0:0:0:0): SCSI status error
> (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
> (probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (probe0:umass-sim0:0:0:0): SCSI status: Check Condition
> (probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (probe0:umass-sim0:0:0:0): Error 6, Unretryable error
> GEOM: new disk da0
> pass2 at umass-sim0 bus 0 scbus3 target 0 lun 0
> pass2: <SD HSUPA Modem > Removable Direct Access SCSI-2 device
> pass2: 40.000MB/s transfers
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> da0 at umass-sim0 bus 0 scbus3 target 0 lun 0
> da0: <SD HSUPA Modem > Removable Direct Access SCSI-2 device
> da0: 40.000MB/s transfers
> da0: Attempt to query device size failed: NOT READY, Medium not present
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): SCSI status error
> (da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
> (da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI status: Check Condition
> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
> (da0:umass-sim0:0:0:0): Error 6, Unretryable error
> Opened disk da0 -> 6
>
> Here's the relevant output via sysctl(1):
>
> dev.uhso.0.%desc: Diagnostic
> dev.uhso.0.%driver: uhso
> dev.uhso.0.%location: bus=1 hubaddr=1 port=6 devaddr=2 interface=0
> dev.uhso.0.%pnpinfo: vendor=0x0af0 product=0x7a05 devclass=0xff
> devsubclass=0xff sernum="" release=0x0000 intclass=0xff
> intsubclass=0xff ttyname=U0 ttyports=1
> dev.uhso.0.%parent: uhub6
> dev.uhso.0.type: Serial
> dev.uhso.0.radio: 1
> dev.uhso.0.ports: 1
> dev.uhso.0.port.diagnostic.tty: cuaU0
> dev.uhso.0.port.diagnostic.desc: Diagnostic
> dev.uhso.1.%desc: Application
> dev.uhso.1.%driver: uhso
> dev.uhso.1.%location: bus=1 hubaddr=1 port=6 devaddr=2 interface=3
> dev.uhso.1.%pnpinfo: vendor=0x0af0 product=0x7a05 devclass=0xff
> devsubclass=0xff sernum="" release=0x0000 intclass=0xff
> intsubclass=0xff ttyname=U1 ttyports=1
> dev.uhso.1.%parent: uhub6
> dev.uhso.1.type: Serial
> dev.uhso.1.radio: 1
> dev.uhso.1.ports: 1
> dev.uhso.1.port.application.tty: cuaU1
> dev.uhso.1.port.application.desc: Application
> dev.uhso.2.%desc: Control
> dev.uhso.2.%driver: uhso
> dev.uhso.2.%location: bus=1 hubaddr=1 port=6 devaddr=2 interface=4
> dev.uhso.2.%pnpinfo: vendor=0x0af0 product=0x7a05 devclass=0xff
> devsubclass=0xff sernum="" release=0x0000 intclass=0xff
> intsubclass=0xff ttyname=U2 ttyports=1
> dev.uhso.2.%parent: uhub6
> dev.uhso.2.type: Serial
> dev.uhso.2.radio: 1
> dev.uhso.2.ports: 1
> dev.uhso.2.port.control.tty: cuaU2
> dev.uhso.2.port.control.desc: Control
> dev.uhso.3.%desc: Network
> dev.uhso.3.%driver: uhso
> dev.uhso.3.%location: bus=1 hubaddr=1 port=6 devaddr=2 interface=5
> dev.uhso.3.%pnpinfo: vendor=0x0af0 product=0x7a05 devclass=0xff
> devsubclass=0xff sernum="" release=0x0000 intclass=0xff
> intsubclass=0xff
> dev.uhso.3.%parent: uhub6
> dev.uhso.3.netif: uhso0
> dev.uhso.3.type: Network
> dev.uhso.3.radio: 1
> dev.uhso.4.%desc: Modem
> dev.uhso.4.%driver: uhso
> dev.uhso.4.%location: bus=1 hubaddr=1 port=6 devaddr=2 interface=6
> dev.uhso.4.%pnpinfo: vendor=0x0af0 product=0x7a05 devclass=0xff
> devsubclass=0xff sernum="" release=0x0000 intclass=0xff
> intsubclass=0xff ttyname=U3 ttyports=1
> dev.uhso.4.%parent: uhub6
> dev.uhso.4.type: Serial
> dev.uhso.4.radio: 1
> dev.uhso.4.ports: 1
> dev.uhso.4.port.modem.tty: cuaU3
> dev.uhso.4.port.modem.desc: Modem
>
> I haven't been able to get the device to work yet. I really don't know
> exactly what I'm doing though :)
>
> I have been able to get the device to respond to this command:
>
> brandon at x300:~$ sudo uhsoctl -a wap.cingular -r /etc/resolv.conf uhso0
> Registered to "AT&T" (UMTS)
>
> Also, I tried doing something like this (as per the uhso(4) man page):
>
> brandon at x300:~$ sudo cu -l /dev/cuaU2
> Connected
> uhso2: failed to set ctrl line state to 0x01: USB_ERR_TIMEOUT
> uhso2: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
> ޭ���T+CGDCONT=1,,
> OK
> uhso1: failed to set ctrl line state to 0x01: USB_ERR_TIMEOUT
> uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
> _OWANCALL: 1, 1
> aޭ��aޭ��Aޭ��Aޭ��Aޭ��Aޭ��Aޭ��Aޭ�ޭ��Aޭ�ޭ��
>
> That's where I'm stuck.
>
> -Brandon
>

A little more output with debugging options enabled in build:

brandon at x300:~$ sudo uhsoctl -a wap.cingular -u WAP at CINGULARGPRS.COM
-k CINGULAR1 uhso0
sysctl dev.uhso.0.%driver returned(0): uhso
sysctl dev.uhso.0.netif returned(-1): FAILED
sysctl dev.uhso.1.%driver returned(0): uhso
sysctl dev.uhso.1.netif returned(-1): FAILED
sysctl dev.uhso.2.%driver returned(0): uhso
sysctl dev.uhso.2.netif returned(-1): FAILED
sysctl dev.uhso.3.%driver returned(0): uhso
sysctl dev.uhso.3.netif returned(0): uhso0
sysctl dev.uhso.3.%location returned(0): bus=1 hubaddr=1 port=6
devaddr=2 interface=5
USB port location=6
sysctl dev.uhso.0.port.control.tty returned(-1): FAILED
sysctl dev.uhso.0.port.application.tty returned(-1): FAILED
sysctl dev.uhso.0.port.application2.tty returned(-1): FAILED
sysctl dev.uhso.1.port.control.tty returned(-1): FAILED
sysctl dev.uhso.1.port.application.tty returned(0): cuaU1
sysctl dev.uhso.1.port.application2.tty returned(-1): FAILED
sysctl dev.uhso.2.port.control.tty returned(0): cuaU2
sysctl dev.uhso.2.port.application.tty returned(-1): FAILED
sysctl dev.uhso.2.port.application2.tty returned(-1): FAILED
sysctl dev.uhso.3.port.control.tty returned(-1): FAILED
sysctl dev.uhso.3.port.application.tty returned(-1): FAILED
sysctl dev.uhso.3.port.application2.tty returned(-1): FAILED
sysctl dev.uhso.4.port.control.tty returned(-1): FAILED
sysctl dev.uhso.4.port.application.tty returned(-1): FAILED
sysctl dev.uhso.4.port.application2.tty returned(-1): FAILED
tty list:
         /dev/cuaU1
         /dev/cuaU2
Attempting to open /dev/cuaU1
SYNC_CMD: AT
SYNC_RESP: AT
SYNC_RESP: OK
SYNC_RETVAL=0
SYNC_CMD: AT+CPIN?
SYNC_EXP: +CPIN: READY (12)
SYNC_RESP: AT+CPIN?
SYNC_RESP: +CPIN: READY
SYNC_RESP: OK
SYNC_RETVAL=0
SYNC_CMD: AT+CGDCONT?
SYNC_EXP: +CGDCONT (8)
SYNC_RESP: AT+CGDCONT?
SYNC_RESP: +CGDCONT: 1,"IP","wap.cingular","0.0.0.0",0,0
Save '+CGDCONT: 1,"IP","wap.cingular","0.0.0.0",0,0'
SYNC_RESP: OK
Save 'OK'
SYNC_RETVAL=0
SYNC_CMD: AT$QCPDPP=1,1,"WAP at CINGULARGPRS.COM","CINGULAR1"
SYNC_RESP: AT$QCPDPP=1,1,"WAP at CINGULARGPRS.COM","CINGULAR1"
SYNC_RESP: OK
SYNC_RETVAL=0
SYNC_CMD: AT_OWANCALL=1,0,0
SYNC_RESP: AT_OWANCALL=1,0,0
SYNC_RESP: OK
SYNC_RETVAL=0
CMD: AT+CGREG?
CMD: AT+CREG?
AT_ASYNC_RESP: AT+CGREG?
AT_ASYNC_RESP: +CGREG: 0,1
CMD: AT+COPS?
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
AT_ASYNC_RESP: AT+CREG?
AT_ASYNC_RESP: +CREG: 0,1
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
AT_ASYNC_RESP: AT+COPS?
AT_ASYNC_RESP: +COPS: 0,0,"AT&T",2
Registered to "AT&T" (UMTS)
CMD: AT_OWANCALL=1,1,1
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
AT_ASYNC_RESP: AT_OWANCALL=1,1,1
AT_ASYNC_RESP: OK
CMD: AT+CGREG?
AT_ASYNC_RESP: AT+CGREG?
AT_ASYNC_RESP: +CGREG: 0,1
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 9,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 7,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 11,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 11,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 11,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
AT_ASYNC_RESP: AT+CSQ
AT_ASYNC_RESP: +CSQ: 11,99
AT_ASYNC_RESP:
AT_ASYNC_RESP: OK
CMD: AT+CSQ
...

>From dmesg, with USB_DEBUG and UHSO_DEBUG defined in uhso.c:

ugen6.2: <Option N.V.> at usbus6
ugen6.2: <Option N.V.> at usbus6 (disconnected)
ugen6.2: <Option N.V.> at usbus6
uhso0: <Diagnostic port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso0: "Diagnostic" port at cuaU0
uhso1: <Application port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso1: "Application" port at cuaU1
uhso2: <Control port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso2: "Control" port at cuaU2
uhso0: bpf attached
uhso3: <Network port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso4: <Modem port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso4: "Modem" port at cuaU3
umass0: <Option N.V. Globetrotter HSUPA Modem, rev 2.00/0.00, addr 2> on usbus6
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:3:0:-1: Attached to scbus3
(probe0:umass-sim0:0:0:0): SCSI status error
(probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI status: Check Condition
(probe0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(probe0:umass-sim0:0:0:0): Error 6, Unretryable error
GEOM: new disk da0
pass2 at umass-sim0 bus 0 scbus3 target 0 lun 0
pass2: <SD HSUPA Modem > Removable Direct Access SCSI-2 device
pass2: 40.000MB/s transfers
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
da0 at umass-sim0 bus 0 scbus3 target 0 lun 0
da0: <SD HSUPA Modem > Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
(da0:umass-sim0:0:0:0): SCSI status error
(da0:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da0:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da0:umass-sim0:0:0:0): SCSI status: Check Condition
(da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not present)
(da0:umass-sim0:0:0:0): Error 6, Unretryable error
Opened disk da0 -> 6
uhso1: failed to set ctrl line state to 0x01: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=0, type=1[Diagnostic]
uhso_probe_iface: Probing for interface 0, probe_func=0xffffffff80e46280
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=0, type=1[Diagnostic]
uhso_probe_iface: Probe result 4010006
uhso_alloc_tty: Allocated TTY 0
uhso0: <Diagnostic port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso0: "Diagnostic" port at cuaU0
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=1, type=2[GPS]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=1, type=2[GPS]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=2, type=3[GPS Control]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=2, type=3[GPS Control]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=3, type=4[Application]
uhso_probe_iface: Probing for interface 3, probe_func=0xffffffff80e46280
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=3, type=4[Application]
uhso_probe_iface: Probe result 4010002
uhso_alloc_tty: Allocated TTY 0
uhso1: <Application port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso1: "Application" port at cuaU1
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=4, type=6[Control]
uhso_probe_iface: Probing for interface 4, probe_func=0xffffffff80e46280
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=4, type=6[Control]
uhso_probe_iface: Probe result 4010001
uhso_alloc_tty: Allocated TTY 0
uhso2: <Control port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso2: "Control" port at cuaU2
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=5, type=7[Network]
uhso_probe_iface: Probing for interface 5, probe_func=0xffffffff80e46280
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=5, type=7[Network]
uhso_probe_iface: Probe result 3030005
uhso0: bpf attached
uhso3: <Network port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=6, type=8[Modem]
uhso_probe_iface: Probing for interface 6, probe_func=0xffffffff80e46280
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=6, type=8[Modem]
uhso_probe_iface: Probe result 4010004
uhso_alloc_tty: Allocated TTY 0
uhso4: <Modem port> at <Option N.V. Globetrotter HSUPA Modem> on uhub6
uhso4: "Modem" port at cuaU3
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=1, type=2[GPS]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=1, type=2[GPS]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=2, type=3[GPS Control]
uhso_probe_iface_auto: actlen=17
uhso_probe_iface_auto: index=2, type=3[GPS Control]
uhso1: failed to set ctrl line state to 0x01: USB_ERR_TIMEOUT
uhso1: failed to set ctrl line state to 0x03: USB_ERR_TIMEOUT

-Brandon