LSI supported mps(4) driver in stable/9 and stable/8
Desai, Kashyap
Kashyap.Desai at lsi.com
Fri Feb 3 15:15:48 UTC 2012
Try attached patch.! (This patch is not taken against upstream code, so you may see some hunk fail.)
~ Kashyap
> -----Original Message-----
> From: Johan Hendriks [mailto:joh.hendriks at gmail.com]
> Sent: Friday, February 03, 2012 8:42 PM
> To: Desai, Kashyap
> Cc: freebsd-stable
> Subject: Re: LSI supported mps(4) driver in stable/9 and stable/8
>
> Desai, Kashyap schreef:
> > Hi Johan,
> >
> > I have already figure out this issue in our lab.
> >
> > I also have fix for this issue. (Just don't want to create regression,
> that is why I have not posted outside)
> > Since you have seen similar issue, It is worth to try my patch.
> >
> > My machine is not getting IP right now. I will send you patch once my
> machine is in network ?
> >
> > ~ Kashyap
> >
> >
> >> -----Original Message-----
> >> From: owner-freebsd-stable at freebsd.org [mailto:owner-freebsd-
> >> stable at freebsd.org] On Behalf Of Johan Hendriks
> >> Sent: Friday, February 03, 2012 8:13 PM
> >> To: Kenneth D. Merry
> >> Cc: freebsd-stable
> >> Subject: Re: LSI supported mps(4) driver in stable/9 and stable/8
> >>
> >> Kenneth D. Merry schreef:
> >>> Hi folks,
> >>>
> >>> The LSI-supported version of the mps(4) driver that supports their
> 6Gb
> >> SAS
> >>> HBAs as well as WarpDrive controllers, is now in stable/9 and
> >> stable/8.
> >>> Please test it out and let me and Kashyap (CCed) know if you run
> into
> >>> any problems.
> >>>
> >>> In addition to supporting WarpDrive, the driver also supports
> >> Integrated
> >>> RAID.
> >>>
> >>> Thanks to LSI for doing the work on this driver!
> >>>
> >>> Note that the CAM infrastructure changes that went into FreeBSD/head
> >> along
> >>> with this driver have not gone into either stable/9 or stable/8.
> Only
> >> the
> >>> driver itself has been merged.
> >>>
> >>> The CAM infrastructure changes depend on some other da(4) driver
> >> changes
> >>> that will need to get merged before they can go back. If that merge
> >>> happens, it will probably only be into stable/9.
> >>>
> >>> A couple of notes about issues with this driver:
> >>>
> >>> - Unlike the previous mps(4) driver, it probes sequentially. If
> you
> >> have
> >>> a lot of drives in your system, it will take a while to probe
> them
> >> all.
> >>> - You may see warning messages like this:
> >>>
> >>> _mapping_add_new_device: failed to add the device with handle 0x0019
> >> to persiste
> >>> nt table because there is no free space available
> >>> _mapping_add_new_device: failed to add the device with handle 0x001a
> >> to persiste
> >>> nt table because there is no free space available
> >>>
> >>> - The driver is not endian safe. (It assumes a little endian
> >> machine.)
> >>> This is not new, the previous version of the driver had the
> same
> >> issue.
> >>> The LSI folks know about these issues. The driver has passed their
> >> testing
> >>> process.
> >>>
> >>> Many thanks to LSI for going through the effort to support FreeBSD.
> >>>
> >>> Ken
> >> Hello Ken.
> >>
> >> Just updated our 16 bay server. did a csup today.
> >> did try some commands, it looked like the drives got husseled.
> >>
> >> But after giving the command camcontrol rescan all it does not give
> back
> >> the prompt.
> >> Also top shows me the following.
> >> 1589 root 1 20 0 16384K 1376K cbwait 3 0:00 0.00%
> >> camcontrol
> >>
> >> # on another console things works
> >> filer01# camcontrol devlist
> >> <ATA WDC WD800JD-60LS 1D07> at scbus0 target 8 lun 0
> (pass0,da0)
> >> <ATA WDC WD800JD-60LS 1D07> at scbus0 target 9 lun 0
> (pass1,da1)
> >> <ATA WDC WD2500AAJS-6 2E25> at scbus0 target 10 lun 0
> (pass2,da2)
> >> <ATA WDC WD2500JS-60M 2E04> at scbus0 target 11 lun 0
> (pass3,da3)
> >> <ATA WDC WD2500JS-60M 2E04> at scbus0 target 12 lun 0
> (pass4,da4)
> >> <ATA ST3250620NS BJH> at scbus0 target 13 lun 0
> (pass5,da5)
> >> <LSI CORP SAS2X28 0717> at scbus0 target 16 lun 0
> >> (probe16,ses0,pass6)
> >> <ATA Maxtor 6L080M0 1G10> at scbus0 target 17 lun 0
> (pass7,da6)
> >> <ATA Maxtor 6L080M0 1G10> at scbus0 target 18 lun 0
> (pass8,da7)
> >> <ATA WDC WD800JD-60LS 1D07> at scbus0 target 19 lun 0
> (pass9,da8)
> >> <ATA WDC WD800JD-60LU 1D07> at scbus0 target 20 lun 0
> >> (pass10,da9)
> >> <ATA GB0250EAFJF HPG6> at scbus0 target 21 lun 0
> >> (pass11,da10)
> >> <ATA ST3250620NS 3BJP> at scbus0 target 22 lun 0
> >> (pass12,da11)
> >> <ATA ST3250620NS 3BJP> at scbus0 target 23 lun 0
> >> (pass13,da12)
> >> <ATA ST3250620NS 3BJP> at scbus0 target 24 lun 0
> >> (pass14,da13)
> >> <ATA ST3250310AS B> at scbus0 target 27 lun 0
> >> (pass15,da14)
> >> <ATA ST3250620NS 3BJP> at scbus0 target 28 lun 0
> >> (pass16,da15)
> >> <ST3808110AS 3.AJJ> at scbus1 target 0 lun 0
> >> (ada0,pass17)
> >> <TSSTcorp CDDVDW SN-208BB SB00> at scbus3 target 0 lun 0
> (pass18,cd0)
> >>
> >> The controller is a LSI 9211-8i with IT firmware.
> >>
> >> here is the dmesg
> >> Copyright (c) 1992-2012 The FreeBSD Project.
> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
> 1994
> >> The Regents of the University of California. All rights
> >> reserved.
> >> FreeBSD is a registered trademark of The FreeBSD Foundation.
> >> FreeBSD 9.0-STABLE #0: Fri Feb 3 10:27:18 CET 2012
> >> root at filer01.neuteboom.local:/usr/obj/usr/src/sys/KRNL amd64
> >> CPU: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz (3093.04-MHz K8-class CPU)
> >> Origin = "GenuineIntel" Id = 0x206a7 Family = 6 Model = 2a
> >> Stepping = 7
> >>
> >>
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE
> >> ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> >>
> >>
> Features2=0x15bae3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SS
> >> SE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE,AVX>
> >> AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
> >> AMD Features2=0x1<LAHF>
> >> TSC: P-state invariant, performance statistics
> >> real memory = 17179869184 (16384 MB)
> >> avail memory = 16493441024 (15729 MB)
> >> Event timer "LAPIC" quality 600
> >> ACPI APIC Table:<SUPERM SMCI--MB>
> >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> >> FreeBSD/SMP: 1 package(s) x 4 core(s)
> >> cpu0 (BSP): APIC ID: 0
> >> cpu1 (AP): APIC ID: 2
> >> cpu2 (AP): APIC ID: 4
> >> cpu3 (AP): APIC ID: 6
> >> ioapic0<Version 2.0> irqs 0-23 on motherboard
> >> kbd1 at kbdmux0
> >> acpi0:<SUPERM SMCI--MB> on motherboard
> >> acpi0: Power Button (fixed)
> >> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
> >> acpi_timer0:<24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
> >> cpu0:<ACPI CPU> on acpi0
> >> cpu1:<ACPI CPU> on acpi0
> >> cpu2:<ACPI CPU> on acpi0
> >> cpu3:<ACPI CPU> on acpi0
> >> pcib0:<ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> >> pci0:<ACPI PCI bus> on pcib0
> >> pcib1:<ACPI PCI-PCI bridge> irq 19 at device 6.0 on pci0
> >> pci1:<ACPI PCI bus> on pcib1
> >> mps0:<LSI SAS2008> port 0xe000-0xe0ff mem 0xfb600000-0xfb603fff irq
> 19
> >> at device 0.0 on pci1
> >> mps0: Firmware: 11.00.00.00, Driver: 11.255.03.00-fbsd
> >> mps0: IOCCapabilities:
> >>
> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDis
> >> c>
> >> em0:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0xf020-0xf03f
> mem
> >> 0xfb800000-0xfb81ffff,0xfb824000-0xfb824fff irq 20 at device 25.0 on
> >> pci0
> >> em0: Using an MSI interrupt
> >> em0: Ethernet address: 00:25:90:57:20:bd
> >> ehci0:<EHCI (generic) USB 2.0 controller> mem 0xfb823000-0xfb8233ff
> irq
> >> 16 at device 26.0 on pci0
> >> usbus0: EHCI version 1.0
> >> usbus0:<EHCI (generic) USB 2.0 controller> on ehci0
> >> pcib2:<ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
> >> pci2:<ACPI PCI bus> on pcib2
> >> pcib3:<ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
> >> pci3:<ACPI PCI bus> on pcib3
> >> em1:<Intel(R) PRO/1000 Network Connection 7.2.3> port 0xd000-0xd01f
> mem
> >> 0xfb700000-0xfb71ffff,0xfb720000-0xfb723fff irq 16 at device 0.0 on
> pci3
> >> em1: Using MSIX interrupts with 3 vectors
> >> em1: Ethernet address: 00:25:90:57:20:bc
> >> ehci1:<EHCI (generic) USB 2.0 controller> mem 0xfb822000-0xfb8223ff
> irq
> >> 23 at device 29.0 on pci0
> >> usbus1: EHCI version 1.0
> >> usbus1:<EHCI (generic) USB 2.0 controller> on ehci1
> >> pcib4:<ACPI PCI-PCI bridge> at device 30.0 on pci0
> >> pci4:<ACPI PCI bus> on pcib4
> >> vgapci0:<VGA-compatible display> mem
> >> 0xf9000000-0xf9ffffff,0xfb000000-0xfb003fff,0xfa800000-0xfaffffff irq
> 23
> >> at device 3.0 on pci4
> >> isab0:<PCI-ISA bridge> at device 31.0 on pci0
> >> isa0:<ISA bus> on isab0
> >> ahci0:<Intel Cougar Point AHCI SATA controller> port
> >> 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf000-0xf01f
> >> mem 0xfb821000-0xfb8217ff irq 19 at device 31.2 on pci0
> >> ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
> >> ahcich0:<AHCI channel> at channel 0 on ahci0
> >> ahcich1:<AHCI channel> at channel 1 on ahci0
> >> ahcich2:<AHCI channel> at channel 2 on ahci0
> >> ahcich3:<AHCI channel> at channel 3 on ahci0
> >> ahcich4:<AHCI channel> at channel 4 on ahci0
> >> ahcich5:<AHCI channel> at channel 5 on ahci0
> >> pci0:<serial bus, SMBus> at device 31.3 (no driver attached)
> >> acpi_button0:<Power Button> on acpi0
> >> hpet0:<High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
> acpi0
> >> ahcich0:<AHCI channel> at channel 0 on ahci0
> >> ahcich1:<AHCI channel> at channel 1 on ahci0
> >> ahcich2:<AHCI channel> at channel 2 on ahci0
> >> ahcich3:<AHCI channel> at channel 3 on ahci0
> >> ahcich4:<AHCI channel> at channel 4 on ahci0
> >> ahcich5:<AHCI channel> at channel 5 on ahci0
> >> pci0:<serial bus, SMBus> at device 31.3 (no driver attached)
> >> acpi_button0:<Power Button> on acpi0
> >> hpet0:<High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
> acpi0
> >> Timecounter "HPET" frequency 14318180 Hz quality 950
> >> Event timer "HPET" frequency 14318180 Hz quality 550
> >> Event timer "HPET1" frequency 14318180 Hz quality 440
> >> Event timer "HPET2" frequency 14318180 Hz quality 440
> >> Event timer "HPET3" frequency 14318180 Hz quality 440
> >> Event timer "HPET4" frequency 14318180 Hz quality 440
> >> attimer0:<AT timer> port 0x40-0x43 irq 0 on acpi0
> >> Timecounter "i8254" frequency 1193182 Hz quality 0
> >> Event timer "i8254" frequency 1193182 Hz quality 100
> >> atrtc0:<AT realtime clock> port 0x70-0x71 irq 8 on acpi0
> >> Event timer "RTC" frequency 32768 Hz quality 0
> >> atkbdc0:<Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> >> atkbd0:<AT Keyboard> irq 1 on atkbdc0
> >> kbd0 at atkbd0
> >> atkbd0: [GIANT-LOCKED]
> >> uart0:<16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on
> acpi0
> >> uart1:<16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
> >> uart2:<16550 or compatible> port 0x3e8-0x3ef irq 10 on acpi0
> >> orm0:<ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff on
> isa0
> >> sc0:<System console> at flags 0x100 on isa0
> >> sc0: VGA<16 virtual consoles, flags=0x300>
> >> vga0:<Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> >> isa0
> >> ppc0: cannot reserve I/O port range
> >> est0:<Enhanced SpeedStep Frequency Control> on cpu0
> >> p4tcc0:<CPU Frequency Thermal Control> on cpu0
> >> est1:<Enhanced SpeedStep Frequency Control> on cpu1
> >> p4tcc1:<CPU Frequency Thermal Control> on cpu1
> >> est2:<Enhanced SpeedStep Frequency Control> on cpu2
> >> p4tcc2:<CPU Frequency Thermal Control> on cpu2
> >> est3:<Enhanced SpeedStep Frequency Control> on cpu3
> >> p4tcc3:<CPU Frequency Thermal Control> on cpu3
> >> ZFS filesystem version 5
> >> ZFS storage pool version 28
> >> Timecounters tick every 1.000 msec
> >> usbus0: 480Mbps High Speed USB v2.0
> >> usbus1: 480Mbps High Speed USB v2.0
> >> ugen0.1:<Intel> at usbus0
> >> uhub0:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
> usbus0
> >> ugen1.1:<Intel> at usbus1
> >> uhub1:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on
> usbus1
> >> da0 at mps0 bus 0 scbus0 target 8 lun 0
> >> da0:<ATA WDC WD800JD-60LS 1D07> Fixed Direct Access SCSI-6 device
> >> da0: 300.000MB/s transfers
> >> da0: Command Queueing enabled
> >> da0: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da1 at mps0 bus 0 scbus0 target 9 lun 0
> >> da1:<ATA WDC WD800JD-60LS 1D07> Fixed Direct Access SCSI-6 device
> >> da1: 300.000MB/s transfers
> >> da1: Command Queueing enabled
> >> da1: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da2 at mps0 bus 0 scbus0 target 10 lun 0
> >> da2:<ATA WDC WD2500AAJS-6 2E25> Fixed Direct Access SCSI-6 device
> >> da2: 300.000MB/s transfers
> >> da2: Command Queueing enabled
> >> da2: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da3 at mps0 bus 0 scbus0 target 11 lun 0
> >> da3:<ATA WDC WD2500JS-60M 2E04> Fixed Direct Access SCSI-6 device
> >> da3: 300.000MB/s transfers
> >> da3: Command Queueing enabled
> >> da3: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da4 at mps0 bus 0 scbus0 target 12 lun 0
> >> da4:<ATA WDC WD2500JS-60M 2E04> Fixed Direct Access SCSI-6 device
> >> da4: 300.000MB/s transfers
> >> da4: Command Queueing enabled
> >> da4: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da5 at mps0 bus 0 scbus0 target 13 lun 0
> >> da5:<ATA ST3250620NS BJH> Fixed Direct Access SCSI-6 device
> >> da5: 150.000MB/s transfers
> >> da5: Command Queueing enabled
> >> da5: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da8 at mps0 bus 0 scbus0 target 19 lun 0
> >> da8:<ATA WDC WD800JD-60LS 1D07> Fixed Direct Access SCSI-6 device
> >> da8: 300.000MB/s transfers
> >> da8: Command Queueing enabled
> >> da8: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da9 at mps0 bus 0 scbus0 target 20 lun 0
> >> da9:<ATA WDC WD800JD-60LU 1D07> Fixed Direct Access SCSI-6 device
> >> da9: 300.000MB/s transfers
> >> da9: Command Queueing enabled
> >> da9: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da11 at mps0 bus 0 scbus0 target 22 lun 0
> >> da11:<ATA ST3250620NS 3BJP> Fixed Direct Access SCSI-6 device
> >> da11: 150.000MB/s transfers
> >> da11: Command Queueing enabled
> >> da11: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da12 at mps0 bus 0 scbus0 target 23 lun 0
> >> da12:<ATA ST3250620NS 3BJP> Fixed Direct Access SCSI-6 device
> >> da12: 150.000MB/s transfers
> >> da12: Command Queueing enabled
> >> da12: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da13 at mps0 bus 0 scbus0 target 24 lun 0
> >> da13:<ATA ST3250620NS 3BJP> Fixed Direct Access SCSI-6 device
> >> da13: 150.000MB/s transfers
> >> da13: Command Queueing enabled
> >> da13: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da14 at mps0 bus 0 scbus0 target 27 lun 0
> >> da14:<ATA ST3250310AS B> Fixed Direct Access SCSI-6 device
> >> da14: 300.000MB/s transfers
> >> da14: Command Queueing enabled
> >> da14: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> da15 at mps0 bus 0 scbus0 target 28 lun 0
> >> da15:<ATA ST3250620NS 3BJP> Fixed Direct Access SCSI-6 device
> >> da15: 150.000MB/s transfers
> >> da15: Command Queueing enabled
> >> da15: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> ses0 at mps0 bus 0 scbus0 target 16 lun 0
> >> ses0:<LSI CORP SAS2X28 0717> Fixed Enclosure Services SCSI-5 device
> >> ses0: 600.000MB/s transfers
> >> ses0: Command Queueing enabled
> >> ses0: SCSI-3 SES Device
> >> ada0 at ahcich0 bus 0 scbus1 target 0 lun 0
> >> ada0:<ST3808110AS 3.AJJ> ATA-7 SATA 1.x device
> >> ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
> >> ada0: 76319MB (156301488 512 byte sectors: 16H 63S/T 16383C)
> >> ada0: Previously was known as ad4
> >> cd0 at ahcich2 bus 0 scbus3 target 0 lun 0
> >> SMP: AP CPU #3 Launched!
> >> cd0:<TSSTcorp CDDVDW SN-208BB SB00> Removable CD-ROM SCSI-0 device
> >> cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO
> >> 8192bytes)
> >> cd0: Attempt to query device size failed: NOT READY, Medium not
> present
> >> - tray closed
> >> SMP: AP CPU #2 Launched!
> >> SMP: AP CPU #1 Launched!
> >> da6 at mps0 bus 0 scbus0 target 17 lun 0
> >> da6:<ATA Maxtor 6L080M0 1G10> Fixed Direct Access SCSI-6 device
> >> da6: 150.000MB/s transfers
> >> da6: Command Queueing enabled
> >> da6: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da7 at mps0 bus 0 scbus0 target 18 lun 0
> >> da7:<ATA Maxtor 6L080M0 1G10> Fixed Direct Access SCSI-6 device
> >> da7: 150.000MB/s transfers
> >> da7: Command Queueing enabled
> >> da7: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
> >> da10 at mps0 bus 0 scbus0 target 21 lun 0
> >> da10:<ATA GB0250EAFJF HPG6> Fixed Direct Access SCSI-6 device
> >> da10: 300.000MB/s transfers
> >> da10: Command Queueing enabled
> >> da10: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
> >> GEOM: da15s1: geometry does not match label (16h,63s != 255h,63s).
> >> uhub1: 2 ports with 2 removable, self powered
> >> uhub0: 2 ports with 2 removable, self powered
> >> Root mount waiting for: usbus1 usbus0
> >> ugen0.2:<vendor 0x8087> at usbus0
> >> uhub2:<vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr
> 2>
> >> on usbus0
> >> ugen1.2:<vendor 0x8087> at usbus1
> >> uhub3:<vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr
> 2>
> >> on usbus1
> >> Root mount waiting for: usbus1 usbus0
> >> uhub3: 6 ports with 6 removable, self powered
> >> uhub2: 6 ports with 6 removable, self powered
> >> ugen0.3:<Winbond Electronics Corp> at usbus0
> >> ums0:<Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0,
> >> rev 1.10/0.01, addr 3> on usbus0
> >> ums0: 3 buttons and [Z] coordinates ID=0
> >> ukbd0:<Winbond Electronics Corp Hermon USB hidmouse Device, class
> 0/0,
> >> rev 1.10/0.01, addr 3> on usbus0
> >> kbd2 at ukbd0
> >> Trying to mount root from ufs:/dev/ada0p2 [rw]...
> >> em0: link state changed to UP
> >>
> >> thanks for your work.
> >>
> >> regards
> >> Johan
> >>
> >>
> >>
> >>
> >> _______________________________________________
> >> freebsd-stable at freebsd.org mailing list
> >> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> >> To unsubscribe, send any mail to "freebsd-stable-
> >> unsubscribe at freebsd.org"
>
> Ok i will try the patch, no hurry, i am back at the office on monday...
> regards
> Johan
-------------- next part --------------
A non-text attachment was scrubbed...
Name: rescan_upstream.patch
Type: application/octet-stream
Size: 31155 bytes
Desc: rescan_upstream.patch
Url : http://lists.freebsd.org/pipermail/freebsd-stable/attachments/20120203/dfe71a35/rescan_upstream-0001.obj
More information about the freebsd-stable
mailing list