LSI supported mps(4) driver in stable/9 and stable/8

Fri Feb 3 15:12:08 UTC 2012

Desai, Kashyap schreef:
> Hi Johan,
>
> I have already figure out this issue in our lab.
>
> I also have fix for this issue. (Just don't want to create regression, that is why I have not posted outside)
> Since you have seen similar issue, It is worth to try my patch.
>
> My machine is not getting IP right now. I will send you patch once my machine is in network ?
>
> ~ Kashyap
>
>
>> -----Original Message-----
>> From: owner-freebsd-stable at freebsd.org [mailto:owner-freebsd-
>> stable at freebsd.org] On Behalf Of Johan Hendriks
>> Sent: Friday, February 03, 2012 8:13 PM
>> To: Kenneth D. Merry
>> Cc: freebsd-stable
>> Subject: Re: LSI supported mps(4) driver in stable/9 and stable/8
>>
>> Kenneth D. Merry schreef:
>>> Hi folks,
>>>
>>> The LSI-supported version of the mps(4) driver that supports their 6Gb
>> SAS
>>> HBAs as well as WarpDrive controllers, is now in stable/9 and
>> stable/8.
>>> Please test it out and let me and Kashyap (CCed) know if you run into
>>> any problems.
>>>
>>> In addition to supporting WarpDrive, the driver also supports
>> Integrated
>>> RAID.
>>>
>>> Thanks to LSI for doing the work on this driver!
>>>
>>> Note that the CAM infrastructure changes that went into FreeBSD/head
>> along
>>> with this driver have not gone into either stable/9 or stable/8.  Only
>> the
>>> driver itself has been merged.
>>>
>>> The CAM infrastructure changes depend on some other da(4) driver
>> changes
>>> that will need to get merged before they can go back.  If that merge
>>> happens, it will probably only be into stable/9.
>>>
>>> A couple of notes about issues with this driver:
>>>
>>>    - Unlike the previous mps(4) driver, it probes sequentially.  If you
>> have
>>>      a lot of drives in your system, it will take a while to probe them
>> all.
>>>    - You may see warning messages like this:
>>>
>>> _mapping_add_new_device: failed to add the device with handle 0x0019
>> to persiste
>>> nt table because there is no free space available
>>> _mapping_add_new_device: failed to add the device with handle 0x001a
>> to persiste
>>> nt table because there is no free space available
>>>
>>>    - The driver is not endian safe.  (It assumes a little endian
>> machine.)
>>>      This is not new, the previous version of the driver had the same
>> issue.
>>> The LSI folks know about these issues.  The driver has passed their
>> testing
>>> process.
>>>
>>> Many thanks to LSI for going through the effort to support FreeBSD.
>>>
>>> Ken
>> Hello Ken.
>>
>> Just updated our 16 bay server. did a csup today.
>> did try some commands, it looked like the drives got husseled.
>>
>> But after giving the command camcontrol rescan all it does not give back
>> the prompt.
>> Also top shows me the following.
>> 1589 root        1  20    0 16384K  1376K cbwait  3   0:00  0.00%
>> camcontrol
>>
>> # on another console things works
>> filer01# camcontrol devlist
>> <ATA WDC WD800JD-60LS 1D07>         at scbus0 target 8 lun 0 (pass0,da0)
>> <ATA WDC WD800JD-60LS 1D07>         at scbus0 target 9 lun 0 (pass1,da1)
>> <ATA WDC WD2500AAJS-6 2E25>         at scbus0 target 10 lun 0 (pass2,da2)
>> <ATA WDC WD2500JS-60M 2E04>         at scbus0 target 11 lun 0 (pass3,da3)
>> <ATA WDC WD2500JS-60M 2E04>         at scbus0 target 12 lun 0 (pass4,da4)
>> <ATA ST3250620NS BJH>               at scbus0 target 13 lun 0 (pass5,da5)
>> <LSI CORP SAS2X28 0717>             at scbus0 target 16 lun 0
>> (probe16,ses0,pass6)
>> <ATA Maxtor 6L080M0 1G10>           at scbus0 target 17 lun 0 (pass7,da6)
>> <ATA Maxtor 6L080M0 1G10>           at scbus0 target 18 lun 0 (pass8,da7)
>> <ATA WDC WD800JD-60LS 1D07>         at scbus0 target 19 lun 0 (pass9,da8)
>> <ATA WDC WD800JD-60LU 1D07>         at scbus0 target 20 lun 0
>> (pass10,da9)
>> <ATA GB0250EAFJF HPG6>              at scbus0 target 21 lun 0
>> (pass11,da10)
>> <ATA ST3250620NS 3BJP>              at scbus0 target 22 lun 0
>> (pass12,da11)
>> <ATA ST3250620NS 3BJP>              at scbus0 target 23 lun 0
>> (pass13,da12)
>> <ATA ST3250620NS 3BJP>              at scbus0 target 24 lun 0
>> (pass14,da13)
>> <ATA ST3250310AS B>                 at scbus0 target 27 lun 0
>> (pass15,da14)
>> <ATA ST3250620NS 3BJP>              at scbus0 target 28 lun 0
>> (pass16,da15)
>> <ST3808110AS 3.AJJ>                 at scbus1 target 0 lun 0
>> (ada0,pass17)
>> <TSSTcorp CDDVDW SN-208BB SB00>     at scbus3 target 0 lun 0 (pass18,cd0)
>>
>> The controller is a LSI 9211-8i with IT firmware.
>>
>> here is the dmesg
>> Copyright (c) 1992-2012 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>>           The Regents of the University of California. All rights
>> reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 9.0-STABLE #0: Fri Feb  3 10:27:18 CET 2012
>>       root at filer01.neuteboom.local:/usr/obj/usr/src/sys/KRNL amd64
>> CPU: Intel(R) Xeon(R) CPU E31220 @ 3.10GHz (3093.04-MHz K8-class CPU)
>>     Origin = "GenuineIntel"  Id = 0x206a7  Family = 6  Model = 2a
>> Stepping = 7
>>
>> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE
>> ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>>
>> Features2=0x15bae3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SS
>> SE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE,AVX>
>>     AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
>>     AMD Features2=0x1<LAHF>
>>     TSC: P-state invariant, performance statistics
>> real memory  = 17179869184 (16384 MB)
>> avail memory = 16493441024 (15729 MB)
>> Event timer "LAPIC" quality 600
>> ACPI APIC Table:<SUPERM SMCI--MB>
>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>> FreeBSD/SMP: 1 package(s) x 4 core(s)
>>    cpu0 (BSP): APIC ID:  0
>>    cpu1 (AP): APIC ID:  2
>>    cpu2 (AP): APIC ID:  4
>>    cpu3 (AP): APIC ID:  6
>> ioapic0<Version 2.0>  irqs 0-23 on motherboard
>> kbd1 at kbdmux0
>> acpi0:<SUPERM SMCI--MB>  on motherboard
>> acpi0: Power Button (fixed)
>> Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
>> acpi_timer0:<24-bit timer at 3.579545MHz>  port 0x408-0x40b on acpi0
>> cpu0:<ACPI CPU>  on acpi0
>> cpu1:<ACPI CPU>  on acpi0
>> cpu2:<ACPI CPU>  on acpi0
>> cpu3:<ACPI CPU>  on acpi0
>> pcib0:<ACPI Host-PCI bridge>  port 0xcf8-0xcff on acpi0
>> pci0:<ACPI PCI bus>  on pcib0
>> pcib1:<ACPI PCI-PCI bridge>  irq 19 at device 6.0 on pci0
>> pci1:<ACPI PCI bus>  on pcib1
>> mps0:<LSI SAS2008>  port 0xe000-0xe0ff mem 0xfb600000-0xfb603fff irq 19
>> at device 0.0 on pci1
>> mps0: Firmware: 11.00.00.00, Driver: 11.255.03.00-fbsd
>> mps0: IOCCapabilities:
>> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDis
>> c>
>> em0:<Intel(R) PRO/1000 Network Connection 7.2.3>  port 0xf020-0xf03f mem
>> 0xfb800000-0xfb81ffff,0xfb824000-0xfb824fff irq 20 at device 25.0 on
>> pci0
>> em0: Using an MSI interrupt
>> em0: Ethernet address: 00:25:90:57:20:bd
>> ehci0:<EHCI (generic) USB 2.0 controller>  mem 0xfb823000-0xfb8233ff irq
>> 16 at device 26.0 on pci0
>> usbus0: EHCI version 1.0
>> usbus0:<EHCI (generic) USB 2.0 controller>  on ehci0
>> pcib2:<ACPI PCI-PCI bridge>  irq 17 at device 28.0 on pci0
>> pci2:<ACPI PCI bus>  on pcib2
>> pcib3:<ACPI PCI-PCI bridge>  irq 17 at device 28.4 on pci0
>> pci3:<ACPI PCI bus>  on pcib3
>> em1:<Intel(R) PRO/1000 Network Connection 7.2.3>  port 0xd000-0xd01f mem
>> 0xfb700000-0xfb71ffff,0xfb720000-0xfb723fff irq 16 at device 0.0 on pci3
>> em1: Using MSIX interrupts with 3 vectors
>> em1: Ethernet address: 00:25:90:57:20:bc
>> ehci1:<EHCI (generic) USB 2.0 controller>  mem 0xfb822000-0xfb8223ff irq
>> 23 at device 29.0 on pci0
>> usbus1: EHCI version 1.0
>> usbus1:<EHCI (generic) USB 2.0 controller>  on ehci1
>> pcib4:<ACPI PCI-PCI bridge>  at device 30.0 on pci0
>> pci4:<ACPI PCI bus>  on pcib4
>> vgapci0:<VGA-compatible display>  mem
>> 0xf9000000-0xf9ffffff,0xfb000000-0xfb003fff,0xfa800000-0xfaffffff irq 23
>> at device 3.0 on pci4
>> isab0:<PCI-ISA bridge>  at device 31.0 on pci0
>> isa0:<ISA bus>  on isab0
>> ahci0:<Intel Cougar Point AHCI SATA controller>  port
>> 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf000-0xf01f
>> mem 0xfb821000-0xfb8217ff irq 19 at device 31.2 on pci0
>> ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
>> ahcich0:<AHCI channel>  at channel 0 on ahci0
>> ahcich1:<AHCI channel>  at channel 1 on ahci0
>> ahcich2:<AHCI channel>  at channel 2 on ahci0
>> ahcich3:<AHCI channel>  at channel 3 on ahci0
>> ahcich4:<AHCI channel>  at channel 4 on ahci0
>> ahcich5:<AHCI channel>  at channel 5 on ahci0
>> pci0:<serial bus, SMBus>  at device 31.3 (no driver attached)
>> acpi_button0:<Power Button>  on acpi0
>> hpet0:<High Precision Event Timer>  iomem 0xfed00000-0xfed003ff on acpi0
>> ahcich0:<AHCI channel>  at channel 0 on ahci0
>> ahcich1:<AHCI channel>  at channel 1 on ahci0
>> ahcich2:<AHCI channel>  at channel 2 on ahci0
>> ahcich3:<AHCI channel>  at channel 3 on ahci0
>> ahcich4:<AHCI channel>  at channel 4 on ahci0
>> ahcich5:<AHCI channel>  at channel 5 on ahci0
>> pci0:<serial bus, SMBus>  at device 31.3 (no driver attached)
>> acpi_button0:<Power Button>  on acpi0
>> hpet0:<High Precision Event Timer>  iomem 0xfed00000-0xfed003ff on acpi0
>> Timecounter "HPET" frequency 14318180 Hz quality 950
>> Event timer "HPET" frequency 14318180 Hz quality 550
>> Event timer "HPET1" frequency 14318180 Hz quality 440
>> Event timer "HPET2" frequency 14318180 Hz quality 440
>> Event timer "HPET3" frequency 14318180 Hz quality 440
>> Event timer "HPET4" frequency 14318180 Hz quality 440
>> attimer0:<AT timer>  port 0x40-0x43 irq 0 on acpi0
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> Event timer "i8254" frequency 1193182 Hz quality 100
>> atrtc0:<AT realtime clock>  port 0x70-0x71 irq 8 on acpi0
>> Event timer "RTC" frequency 32768 Hz quality 0
>> atkbdc0:<Keyboard controller (i8042)>  port 0x60,0x64 irq 1 on acpi0
>> atkbd0:<AT Keyboard>  irq 1 on atkbdc0
>> kbd0 at atkbd0
>> atkbd0: [GIANT-LOCKED]
>> uart0:<16550 or compatible>  port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
>> uart1:<16550 or compatible>  port 0x2f8-0x2ff irq 3 on acpi0
>> uart2:<16550 or compatible>  port 0x3e8-0x3ef irq 10 on acpi0
>> orm0:<ISA Option ROMs>  at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff on isa0
>> sc0:<System console>  at flags 0x100 on isa0
>> sc0: VGA<16 virtual consoles, flags=0x300>
>> vga0:<Generic ISA VGA>  at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
>> isa0
>> ppc0: cannot reserve I/O port range
>> est0:<Enhanced SpeedStep Frequency Control>  on cpu0
>> p4tcc0:<CPU Frequency Thermal Control>  on cpu0
>> est1:<Enhanced SpeedStep Frequency Control>  on cpu1
>> p4tcc1:<CPU Frequency Thermal Control>  on cpu1
>> est2:<Enhanced SpeedStep Frequency Control>  on cpu2
>> p4tcc2:<CPU Frequency Thermal Control>  on cpu2
>> est3:<Enhanced SpeedStep Frequency Control>  on cpu3
>> p4tcc3:<CPU Frequency Thermal Control>  on cpu3
>> ZFS filesystem version 5
>> ZFS storage pool version 28
>> Timecounters tick every 1.000 msec
>> usbus0: 480Mbps High Speed USB v2.0
>> usbus1: 480Mbps High Speed USB v2.0
>> ugen0.1:<Intel>  at usbus0
>> uhub0:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1>  on usbus0
>> ugen1.1:<Intel>  at usbus1
>> uhub1:<Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1>  on usbus1
>> da0 at mps0 bus 0 scbus0 target 8 lun 0
>> da0:<ATA WDC WD800JD-60LS 1D07>  Fixed Direct Access SCSI-6 device
>> da0: 300.000MB/s transfers
>> da0: Command Queueing enabled
>> da0: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da1 at mps0 bus 0 scbus0 target 9 lun 0
>> da1:<ATA WDC WD800JD-60LS 1D07>  Fixed Direct Access SCSI-6 device
>> da1: 300.000MB/s transfers
>> da1: Command Queueing enabled
>> da1: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da2 at mps0 bus 0 scbus0 target 10 lun 0
>> da2:<ATA WDC WD2500AAJS-6 2E25>  Fixed Direct Access SCSI-6 device
>> da2: 300.000MB/s transfers
>> da2: Command Queueing enabled
>> da2: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da3 at mps0 bus 0 scbus0 target 11 lun 0
>> da3:<ATA WDC WD2500JS-60M 2E04>  Fixed Direct Access SCSI-6 device
>> da3: 300.000MB/s transfers
>> da3: Command Queueing enabled
>> da3: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da4 at mps0 bus 0 scbus0 target 12 lun 0
>> da4:<ATA WDC WD2500JS-60M 2E04>  Fixed Direct Access SCSI-6 device
>> da4: 300.000MB/s transfers
>> da4: Command Queueing enabled
>> da4: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da5 at mps0 bus 0 scbus0 target 13 lun 0
>> da5:<ATA ST3250620NS BJH>  Fixed Direct Access SCSI-6 device
>> da5: 150.000MB/s transfers
>> da5: Command Queueing enabled
>> da5: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da8 at mps0 bus 0 scbus0 target 19 lun 0
>> da8:<ATA WDC WD800JD-60LS 1D07>  Fixed Direct Access SCSI-6 device
>> da8: 300.000MB/s transfers
>> da8: Command Queueing enabled
>> da8: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da9 at mps0 bus 0 scbus0 target 20 lun 0
>> da9:<ATA WDC WD800JD-60LU 1D07>  Fixed Direct Access SCSI-6 device
>> da9: 300.000MB/s transfers
>> da9: Command Queueing enabled
>> da9: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da11 at mps0 bus 0 scbus0 target 22 lun 0
>> da11:<ATA ST3250620NS 3BJP>  Fixed Direct Access SCSI-6 device
>> da11: 150.000MB/s transfers
>> da11: Command Queueing enabled
>> da11: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da12 at mps0 bus 0 scbus0 target 23 lun 0
>> da12:<ATA ST3250620NS 3BJP>  Fixed Direct Access SCSI-6 device
>> da12: 150.000MB/s transfers
>> da12: Command Queueing enabled
>> da12: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da13 at mps0 bus 0 scbus0 target 24 lun 0
>> da13:<ATA ST3250620NS 3BJP>  Fixed Direct Access SCSI-6 device
>> da13: 150.000MB/s transfers
>> da13: Command Queueing enabled
>> da13: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da14 at mps0 bus 0 scbus0 target 27 lun 0
>> da14:<ATA ST3250310AS B>  Fixed Direct Access SCSI-6 device
>> da14: 300.000MB/s transfers
>> da14: Command Queueing enabled
>> da14: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> da15 at mps0 bus 0 scbus0 target 28 lun 0
>> da15:<ATA ST3250620NS 3BJP>  Fixed Direct Access SCSI-6 device
>> da15: 150.000MB/s transfers
>> da15: Command Queueing enabled
>> da15: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> ses0 at mps0 bus 0 scbus0 target 16 lun 0
>> ses0:<LSI CORP SAS2X28 0717>  Fixed Enclosure Services SCSI-5 device
>> ses0: 600.000MB/s transfers
>> ses0: Command Queueing enabled
>> ses0: SCSI-3 SES Device
>> ada0 at ahcich0 bus 0 scbus1 target 0 lun 0
>> ada0:<ST3808110AS 3.AJJ>  ATA-7 SATA 1.x device
>> ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
>> ada0: 76319MB (156301488 512 byte sectors: 16H 63S/T 16383C)
>> ada0: Previously was known as ad4
>> cd0 at ahcich2 bus 0 scbus3 target 0 lun 0
>> SMP: AP CPU #3 Launched!
>> cd0:<TSSTcorp CDDVDW SN-208BB SB00>  Removable CD-ROM SCSI-0 device
>> cd0: 150.000MB/s transfers (SATA 1.x, UDMA5, ATAPI 12bytes, PIO
>> 8192bytes)
>> cd0: Attempt to query device size failed: NOT READY, Medium not present
>> - tray closed
>> SMP: AP CPU #2 Launched!
>> SMP: AP CPU #1 Launched!
>> da6 at mps0 bus 0 scbus0 target 17 lun 0
>> da6:<ATA Maxtor 6L080M0 1G10>  Fixed Direct Access SCSI-6 device
>> da6: 150.000MB/s transfers
>> da6: Command Queueing enabled
>> da6: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da7 at mps0 bus 0 scbus0 target 18 lun 0
>> da7:<ATA Maxtor 6L080M0 1G10>  Fixed Direct Access SCSI-6 device
>> da7: 150.000MB/s transfers
>> da7: Command Queueing enabled
>> da7: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C)
>> da10 at mps0 bus 0 scbus0 target 21 lun 0
>> da10:<ATA GB0250EAFJF HPG6>  Fixed Direct Access SCSI-6 device
>> da10: 300.000MB/s transfers
>> da10: Command Queueing enabled
>> da10: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
>> GEOM: da15s1: geometry does not match label (16h,63s != 255h,63s).
>> uhub1: 2 ports with 2 removable, self powered
>> uhub0: 2 ports with 2 removable, self powered
>> Root mount waiting for: usbus1 usbus0
>> ugen0.2:<vendor 0x8087>  at usbus0
>> uhub2:<vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2>
>> on usbus0
>> ugen1.2:<vendor 0x8087>  at usbus1
>> uhub3:<vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2>
>> on usbus1
>> Root mount waiting for: usbus1 usbus0
>> uhub3: 6 ports with 6 removable, self powered
>> uhub2: 6 ports with 6 removable, self powered
>> ugen0.3:<Winbond Electronics Corp>  at usbus0
>> ums0:<Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0,
>> rev 1.10/0.01, addr 3>  on usbus0
>> ums0: 3 buttons and [Z] coordinates ID=0
>> ukbd0:<Winbond Electronics Corp Hermon USB hidmouse Device, class 0/0,
>> rev 1.10/0.01, addr 3>  on usbus0
>> kbd2 at ukbd0
>> Trying to mount root from ufs:/dev/ada0p2 [rw]...
>> em0: link state changed to UP
>>
>> thanks for your work.
>>
>> regards
>> Johan
>>
>>
>>
>>
>> _______________________________________________
>> freebsd-stable at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
>> To unsubscribe, send any mail to "freebsd-stable-
>> unsubscribe at freebsd.org"

Ok i will try the patch, no hurry, i am back at the office on monday...
regards
Johan