Adaptec 2120S & 4.7-STABLE
Scott Long
scottl at freebsd.org
Thu Oct 9 05:22:59 PDT 2003
Hi,
Yes, the 'Optional battery present' message is wrong and I just haven't
gotten around to fixing it. For your other problem, you need to remove
the 'aacp' device from your kernel config. It's an option sub-device of
aac and seems to cause many more problems than it's worth.
Scott
Lauri Laupmaa wrote:
> Hi
>
> I have strange problem with aforementioned adaptec raid controller and
> 4.7-STABLE.
> The controller is detected by kernel, but for some awkward reason with
> optional battery, which is not present actually (aaccli shows correct
> info). The biggest problem, however, is that while system works from
> ide drives and empty 2120S, it stops working (doesn't boot) when raid
> disks are connected, the kernel just repeats last messaga:
> aac0: **Monitor** SCSI bus reset issued on channel 0
> I have 3 other servers with 2120S, RAID5 and no IDE, all running 5.X.
>
> My questions:
> a. Should 2120S work with 4.X and specifically with 4.7?
> b. Could this be hardware problem?
> c. Could this be firmware problem (my other 2120 controllers have Build
> #5770 BIOS)
>
> TIA
> L.
>
> Relevant info:
> kernel:
> bash-2.05a# uname -a
> FreeBSD doall.blaah.com 4.7-STABLE FreeBSD 4.7-STABLE #6: Thu Nov 7
> 03:37:32 EET 2002 root at doall.blaah.com:/usr/obj/usr/src/sys/DOALL
> i386
>
> dmesg:
> Copyright (c) 1992-2002 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 4.7-STABLE #6: Thu Nov 7 03:37:32 EET 2002
> root at doall.codewiser.com:/usr/obj/usr/src/sys/DOALL
> Timecounter "i8254" frequency 1193182 Hz
> CPU: Pentium III/Pentium III Xeon/Celeron (863.87-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x68a Stepping = 10
>
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C
> MOV,PAT,PSE36,MMX,FXSR,SSE>
> real memory = 536608768 (524032K bytes)
> avail memory = 516874240 (504760K bytes)
> Preloaded elf kernel "kernel" at 0xc051d000.
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 12 entries at 0xc00f2ed0
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on
> pci0
> pci2: <PCI bus> on pcib1
> pci2: <ATI Mach64-GM graphics accelerator> at 0.0 irq 11
> pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
> pci1: <PCI bus> on pcib2
> fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xce80-0xcebf mem
> 0xfc980000-0xfc99ffff,0xfc9ee000-0xfc9eefff irq 9 at device 9.0 on pci1
> fxp0: Ethernet address 00:02:b3:46:5a:8c
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xcf00-0xcf3f mem
> 0xfc9c0000-0xfc9dffff,0xfc9ef000-0xfc9effff irq 4 at device 10.0 on pci1
> fxp1: Ethernet address 00:02:b3:8d:46:4b
> inphy1: <i82555 10/100 media interface> on miibus1
> inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> aac0: <Adaptec SCSI RAID 2120S> mem 0xf0000000-0xf3ffffff irq 9 at
> device 13.0 on pci1
> aac0: i960RX 100MHz, 48MB cache memory, optional battery present
> aac0: Kernel 4.0-0, Build 6003, S/N b85172
> aacp0: <SCSI Passthrough Bus> on aac0
> isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH2 ATA100 controller> port 0xffa0-0xffaf at device
> 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port
> 0xef40-0xef5f irq 7 at device 31.2 on pci0
> usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10
> uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port
> 0xef80-0xef9f irq 3 at device 31.4 on pci0
> usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> pci0: <unknown card> (vendor=0x8086, dev=0x2445) at 31.5 irq 10
> orm0: <Option ROMs> at iomem
> 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcefff on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 8250
> sio1: configured irq 3 not in bitmap of probed irqs 0
> ppc0: parallel port not found.
> ad0: 9773MB <FUJITSU MPF3102AT> [19857/16/63] at ata0-master UDMA66
> ad2: 38172MB <QUANTUM FIREBALLP AS40.0> [77557/16/63] at ata1-master
> UDMA100
> ad3: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata1-slave UDMA33
> acd0: CDROM <LTN526D> at ata0-slave PIO4
> Waiting 15 seconds for SCSI devices to settle
> aac0: **Monitor** SCSI bus reset issued on channel 0
> aac0: **Monitor** PrintfToHost timeout
> aac0: unknown command from controller
> Mounting root from ufs:/dev/ad0s1a
>
> aacli:
> AAC0> controller details
> Executing: controller details
> Controller Information
> ----------------------
> Remote Computer: S
> Device Name: S
> Controller Type: No Info
> Access Mode: READ-WRITE
> Controller Serial Number: Last Six Digits = B85172
> Number of Buses: 1
> Devices per Bus: 15
> Controller CPU: i960 R series
> Controller CPU Speed: 100 Mhz
> Controller Memory: 64 Mbytes
> Battery State: Not Present
>
> Component Revisions
> -------------------
> CLI: 1.0-0 (Build #5263)
> API: 1.0-0 (Build #5263)
> Miniport Driver: 4.0-0 (Build #6003)
> Controller Software: 4.0-0 (Build #6003)
> Controller BIOS: 4.0-0 (Build #6003)
> Controller Firmware: (Build #6003)
> Controller Hardware: 2.64
>
> _______________________________________________
> freebsd-scsi at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-scsi
> To unsubscribe, send any mail to "freebsd-scsi-unsubscribe at freebsd.org"
>
More information about the freebsd-scsi
mailing list