Adaptec 2120S & 4.7-STABLE

[Lauri Laupmaa]

Hi

I have strange problem with aforementioned adaptec raid controller and  
4.7-STABLE.
The controller is detected by kernel, but for some awkward reason with  
optional battery, which is not present actually (aaccli shows correct  
info). The biggest problem, however, is that while system works from  
ide drives and empty 2120S, it stops working (doesn't boot) when raid  
disks are connected, the kernel just repeats last messaga:
aac0: **Monitor** SCSI bus reset issued on channel 0
I have 3 other servers with 2120S, RAID5 and no IDE, all running 5.X.

My questions:
a. Should 2120S work with 4.X and specifically with 4.7?
b. Could this be hardware problem?
c. Could this be firmware problem (my other 2120 controllers have Build  
#5770 BIOS)

TIA
L.

Relevant info:
kernel:
bash-2.05a# uname -a
FreeBSD doall.blaah.com 4.7-STABLE FreeBSD 4.7-STABLE #6: Thu Nov  7  
03:37:32 EET 2002     root at doall.blaah.com:/usr/obj/usr/src/sys/DOALL   
i386

dmesg:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights  
reserved.
FreeBSD 4.7-STABLE #6: Thu Nov  7 03:37:32 EET 2002
     root at doall.codewiser.com:/usr/obj/usr/src/sys/DOALL
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (863.87-MHz 686-class CPU)
   Origin = "GenuineIntel"  Id = 0x68a  Stepping = 10
    
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C 
MOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 536608768 (524032K bytes)
avail memory = 516874240 (504760K bytes)
Preloaded elf kernel "kernel" at 0xc051d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f2ed0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on  
pci0
pci2: <PCI bus> on pcib1
pci2: <ATI Mach64-GM graphics accelerator> at 0.0 irq 11
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on  
pci0
pci1: <PCI bus> on pcib2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xce80-0xcebf mem  
0xfc980000-0xfc99ffff,0xfc9ee000-0xfc9eefff irq 9 at device 9.0 on pci1
fxp0: Ethernet address 00:02:b3:46:5a:8c
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xcf00-0xcf3f mem  
0xfc9c0000-0xfc9dffff,0xfc9ef000-0xfc9effff irq 4 at device 10.0 on pci1
fxp1: Ethernet address 00:02:b3:8d:46:4b
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
aac0: <Adaptec SCSI RAID 2120S> mem 0xf0000000-0xf3ffffff irq 9 at  
device 13.0 on pci1
aac0: i960RX 100MHz, 48MB cache memory, optional battery present
aac0: Kernel 4.0-0, Build 6003, S/N b85172
aacp0: <SCSI Passthrough Bus> on aac0
isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on  
pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0xffa0-0xffaf at device  
31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port  
0xef40-0xef5f irq 7 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port  
0xef80-0xef9f irq 3 at device 31.4 on pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x2445) at 31.5 irq 10
orm0: <Option ROMs> at iomem  
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcefff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on  
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on  
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: parallel port not found.
ad0: 9773MB <FUJITSU MPF3102AT> [19857/16/63] at ata0-master UDMA66
ad2: 38172MB <QUANTUM FIREBALLP AS40.0> [77557/16/63] at ata1-master  
UDMA100
ad3: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata1-slave UDMA33
acd0: CDROM <LTN526D> at ata0-slave PIO4
Waiting 15 seconds for SCSI devices to settle
aac0: **Monitor** SCSI bus reset issued on channel 0
aac0: **Monitor** PrintfToHost timeout
aac0: unknown command from controller
Mounting root from ufs:/dev/ad0s1a

aacli:
AAC0> controller details
Executing: controller details
Controller Information
----------------------
          Remote Computer: S
              Device Name: S
          Controller Type: No Info
              Access Mode: READ-WRITE
Controller Serial Number: Last Six Digits = B85172
          Number of Buses: 1
          Devices per Bus: 15
           Controller CPU: i960 R series
     Controller CPU Speed: 100 Mhz
        Controller Memory: 64 Mbytes
            Battery State: Not Present

Component Revisions
-------------------
                 CLI: 1.0-0 (Build #5263)
                 API: 1.0-0 (Build #5263)
     Miniport Driver: 4.0-0 (Build #6003)
Controller Software: 4.0-0 (Build #6003)
     Controller BIOS: 4.0-0 (Build #6003)
Controller Firmware: (Build #6003)
Controller Hardware: 2.64