ath: unable to attach hardware; HAL status 3; attach returned 6
Ian
ianglenn at gmail.com
Tue Aug 12 19:54:32 UTC 2008
Goal:
to have Wireless Atheros based NIC run on my Sony Vaio
Background:
The computer in question is a Sony Vaio PCG R505-JL w/ slimdock. The CD-ROM
is broken.
I used a second computer and installed it on the second computer, then
transfered the
hard drive to the vaio.
This problem is not present on the computer I installed it on. The card
works Out-of box.
dmesg output:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-STABLE #3: Sun Aug 10 23:59:57 EDT 2008
root@:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (745.25-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 401080320 (382 MB)
avail memory = 378433536 (360 MB)
kbd1 at kbdmux0
ath_hal: 0.10.5.6 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413,
RF5413, RF2133, RF2425, RF2417)
acpi0: <SONY U1> on motherboard
acpi0: [ITHREAD]
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x62,0x66 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> mem
0xf8000000-0xfbffffff,0xf4000000-0xf407ffff irq 9 at device 2.0 on pci0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> on vgapci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
fwohci0: <Texas Instruments TSB43AA22> mem
0xf4105000-0xf41057ff,0xf4100000-0xf4103fff irq 9 at device 0.0 on pci1
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 08:00:46:03:00:c5:c2:17
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x17d1c000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:46:c5:c2:17
fwe0: Ethernet address: 0a:00:46:c5:c2:17
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 08:00:46:03:00:c5:c2:17 @ 0xfffe00000000, S400,
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
cbb0: <RF5C475 PCI-CardBus Bridge> at device 2.0 on pci1
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0x3000-0x303f mem
0xf4104000-0xf4104fff irq 9 at device 8.0 on pci1
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 08:00:46:41:96:8d
fxp0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1800-0x180f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f
irq 9 at device 31.2 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x1840-0x185f
irq 9 at device 31.4 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xcbfff,0xd8000-0xdbfff,0xdc000-0xdffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: <Sony USB Memory Stick Slot, class 0/0, rev 1.10/1.83, addr 2> on
uhub1
Timecounter "TSC" frequency 745245771 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 14403MB <TOSHIBA MK1517GAP A1.03 H> at ata0-master UDMA100
cardbus0: Expecting link target, got 0xff
ath0: <Atheros 2413> mem 0xf4110000-0xf411ffff irq 9 at device 0.0 on
cardbus0
ath0: [ITHREAD]
ath0: unable to attach hardware; HAL status 3
device_attach: ath0 attach returned 6
(probe7:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe7:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe7:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe7:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0
(probe7:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred
(probe7:umass-sim0:0:0:0): Retrying Command (per Sense Data)
(probe7:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe7:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe7:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe7:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe7:umass-sim0:0:0:0): Medium not present
(probe7:umass-sim0:0:0:0): Unretryable error
Trying to mount root from ufs:/dev/ad0s1a
umass1: <Memorex TRAVELDRIVE 005B, class 0/0, rev 2.00/1.10, addr 2> on
uhub0
da0 at umass-sim1 bus 1 target 0 lun 0
da0: <Memorex TRAVELDRIVE 005B PMAP> Removable Direct Access SCSI-0 device
da0: 1.000MB/s transfers
da0: 7871MB (16119808 512 byte sectors: 255H 63S/T 1003C)
pciconf -lv:
hostb0 at pci0:0:0:0: class=0x060000 card=0x80e0104d chip=0x11308086
rev=0x11 hdr=0x00
vendor = 'Intel Corporation'
device = '82815/EM/EP/P 815/EM/EP/P (Solano) Host to I/O Hub Bridge'
class = bridge
subclass = HOST-PCI
vgapci0 at pci0:0:2:0: class=0x030000 card=0x80e0104d chip=0x11328086
rev=0x11 hdr=0x00
vendor = 'Intel Corporation'
device = '82815/EM/EP/P 815/EM/EP/P (Solano) Interal GUI
Accelerator'
class = display
subclass = VGA
pcib1 at pci0:0:30:0: class=0x060400 card=0x00000000 chip=0x24488086
rev=0x03 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI
Bridge'
class = bridge
subclass = PCI-PCI
isab0 at pci0:0:31:0: class=0x060100 card=0x00000000 chip=0x244c8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BAM (ICH2-M) LPC Interface Controller'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:0:31:1: class=0x010180 card=0x80e0104d chip=0x244a8086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BAM (ICH2-M) UltraATA/100 IDE Controller'
class = mass storage
subclass = ATA
uhci0 at pci0:0:31:2: class=0x0c0300 card=0x80e0104d chip=0x24428086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) USB Universal Host Controller'
class = serial bus
subclass = USB
none0 at pci0:0:31:3: class=0x0c0500 card=0x80e0104d chip=0x24438086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) SMBus Controller'
class = serial bus
subclass = SMBus
uhci1 at pci0:0:31:4: class=0x0c0300 card=0x80e0104d chip=0x24448086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) USB Universal Host Controller'
class = serial bus
subclass = USB
none1 at pci0:0:31:5: class=0x040100 card=0x80e0104d chip=0x24458086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) AC'97 Audio Controller'
class = multimedia
subclass = audio
none2 at pci0:0:31:6: class=0x070300 card=0x80e0104d chip=0x24468086
rev=0x03 hdr=0x00
vendor = 'Intel Corporation'
device = '82801BA/BAM (ICH2/ICH2-M) AC'97 Modem Controller'
class = simple comms
subclass = generic modem
fwohci0 at pci0:1:0:0: class=0x0c0010 card=0x80e0104d chip=0x8021104c
rev=0x02 hdr=0x00
vendor = 'Texas Instruments (TI)'
device = 'TSB43AA22xxx 1394a-2000 OHCI PHY/Link Layer Ctrlr xxx'
class = serial bus
subclass = FireWire
cbb0 at pci0:1:2:0: class=0x060700 card=0x80e0104d chip=0x04751180 rev=0x80
hdr=0x02
vendor = 'Ricoh Company, Ltd.'
device = 'RL5c475 Cardbus Controller'
class = bridge
subclass = PCI-CardBus
fxp0 at pci0:1:8:0: class=0x020000 card=0x30138086 chip=0x24498086 rev=0x03
hdr=0x00
vendor = 'Intel Corporation'
device = '82559ER 82559ER Integrated 10Base-T/100Base-TX Ethernet
Controller'
class = network
subclass = ethernet
ath0 at pci0:2:0:0: class=0x000000 card=0x000817f9 chip=0x001a168c rev=0x01
hdr=0x00
vendor = 'Atheros Communications Inc.'
device = 'Atheros AR5005G Atheros AR5005G 802.11abg NIC Chipset /
TP-Link (TL-WN551G)'
class = old
subclass = non-VGA display device
According to ah.h (line 84) HAL status 3 is "hardware didn't respond as
expected.
Any more output/logs that are needed can be provided.
Thank you very much for your attention.
Ian Glenn
More information about the freebsd-mobile
mailing list