amd64/186485: Disks are not shown on Adaptec 5805 (added via passthrough to the VM)

[kaczorem]

The following reply was made to PR amd64/186485; it has been noted by GNATS.

From: kaczorem <kaczorem at iem.pw.edu.pl>
To: bug-followup at FreeBSD.org
Cc:  
Subject: Re: amd64/186485: Disks are not shown on Adaptec 5805 (added via
 passthrough to the VM)
Date: Wed, 05 Feb 2014 20:54:46 +0100

 Just I would like to add some additional information:
 
 logs:
 
 
 aac0: <Adaptec RAID 5805> mem 0xfd200000-0xfd3fffff irq 18 at device 0.0 
 on pci3
 aac0: Enabling 64-bit address support
 aac0: Enable Raw I/O
 aac0: Enable 64-bit array
 aac0: New comm. interface enabled
 aac0: Adaptec 5805, aac driver 2.1.9-1
 aacp0 on aac0
 aacp1 on aac0
 aacp2 on aac0
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Retrying command
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Retrying command
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Retrying command
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Retrying command
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Retrying command
 (probe2:aacp2:0:0:0): REPORT LUNS. CDB: a0 00 00 00 00 00 00 00 00 10 00 
 00
 (probe2:aacp2:0:0:0): CAM status: CCB request completed with an error
 (probe2:aacp2:0:0:0): Error 5, Retries exhausted
 ses0 at aacp2 bus 0 scbus4 target 0 lun 0
 ses0: <AIC SES_BP-4D-1F 130a> Fixed Enclosure Services SCSI-5 device
 ses0: 3.300MB/s transfers (8bit)
 ses0: SCSI-3 ENC Device
 
 
 I did tests also on: 9.2 Stable, 10 and 11. The same problem.
 
 The Adaptec controller 5805 has the latest firmware.