svn commit: r192446 - head/sys/dev/usb/controller

[Andrew Thompson]

Author: thompsa
Date: Wed May 20 17:00:55 2009
New Revision: 192446
URL: http://svn.freebsd.org/changeset/base/192446

Log:
  - Add new register definitions
  - Enable the controller and wait for the PLL to start
  
  Submitted by:	Hans Petter Selasky

Modified:
  head/sys/dev/usb/controller/atmegadci.c
  head/sys/dev/usb/controller/atmegadci.h

Modified: head/sys/dev/usb/controller/atmegadci.c
==============================================================================
--- head/sys/dev/usb/controller/atmegadci.c	Wed May 20 17:00:16 2009	(r192445)
+++ head/sys/dev/usb/controller/atmegadci.c	Wed May 20 17:00:55 2009	(r192446)
@@ -672,7 +672,7 @@ atmegadci_interrupt(struct atmegadci_sof
 	 * that like RESUME. Resume is set when there is at least 3
 	 * milliseconds of inactivity on the USB BUS.
 	 */
-	if (status & ATMEGA_UDINT_EORSMI) {
+	if (status & ATMEGA_UDINT_WAKEUPI) {
 
 		DPRINTFN(5, "resume interrupt\n");
 
@@ -700,7 +700,7 @@ atmegadci_interrupt(struct atmegadci_sof
 
 			/* disable suspend interrupt */
 			ATMEGA_WRITE_1(sc, ATMEGA_UDIEN,
-			    ATMEGA_UDINT_EORSMI |
+			    ATMEGA_UDINT_WAKEUPE |
 			    ATMEGA_UDINT_EORSTE);
 
 			/* complete root HUB interrupt endpoint */
@@ -1152,13 +1152,12 @@ atmegadci_clear_stall_sub(struct atmegad
 	    ATMEGA_UECONX_STALLRQC);
 
 	do {
-		temp = 0;
 		if (ep_type == UE_BULK) {
-			temp |= ATMEGA_UECFG0X_EPTYPE2;
+			temp = ATMEGA_UECFG0X_EPTYPE2;
 		} else if (ep_type == UE_INTERRUPT) {
-			temp |= ATMEGA_UECFG0X_EPTYPE3;
+			temp = ATMEGA_UECFG0X_EPTYPE3;
 		} else {
-			temp |= ATMEGA_UECFG0X_EPTYPE1;
+			temp = ATMEGA_UECFG0X_EPTYPE1;
 		}
 		if (ep_dir & UE_DIR_IN) {
 			temp |= ATMEGA_UECFG0X_EPDIR;
@@ -1217,13 +1216,28 @@ atmegadci_init(struct atmegadci_softc *s
 	sc->sc_bus.methods = &atmegadci_bus_methods;
 
 	USB_BUS_LOCK(&sc->sc_bus);
-#if 0
-	/* XXX TODO - currently done by boot strap */
+
+	/* make sure USB is enabled */
+	ATMEGA_WRITE_1(sc, ATMEGA_USBCON,
+	    ATMEGA_USBCON_USBE |
+	    ATMEGA_USBCON_FRZCLK);
 
 	/* enable USB PAD regulator */
 	ATMEGA_WRITE_1(sc, ATMEGA_UHWCON,
-	    ATMEGA_UHWCON_UVREGE | ATMEGA_UHWCON_UIMOD);
-#endif
+	    ATMEGA_UHWCON_UVREGE |
+	    ATMEGA_UHWCON_UIMOD);
+
+	/* the following register sets up the USB PLL, assuming 16MHz X-tal */
+	ATMEGA_WRITE_1(sc, 0x49 /* PLLCSR */, 0x14 | 0x02);
+
+	/* wait for PLL to lock */
+	for (n = 0; n != 20; n++) {
+		if (ATMEGA_READ_1(sc, 0x49) & 0x01)
+			break;
+		/* wait a little bit for PLL to start */
+		usb2_pause_mtx(&sc->sc_bus.bus_mtx, hz / 100);
+	}
+
 	/* make sure USB is enabled */
 	ATMEGA_WRITE_1(sc, ATMEGA_USBCON,
 	    ATMEGA_USBCON_USBE |
@@ -1847,6 +1861,11 @@ tr_handle_clear_port_feature:
 		/* clear connect change flag */
 		sc->sc_flags.change_connect = 0;
 
+		if (!sc->sc_flags.status_bus_reset) {
+			/* we are not connected */
+			break;
+		}
+
 		/* configure the control endpoint */
 
 		/* select endpoint number */

Modified: head/sys/dev/usb/controller/atmegadci.h
==============================================================================
--- head/sys/dev/usb/controller/atmegadci.h	Wed May 20 17:00:16 2009	(r192445)
+++ head/sys/dev/usb/controller/atmegadci.h	Wed May 20 17:00:55 2009	(r192446)
@@ -34,6 +34,10 @@
 
 #define	ATMEGA_MAX_DEVICES (USB_MIN_DEVICES + 1)
 
+#define	ATMEGA_OTGTCON 0xF9
+#define	ATMEGA_OTGTCON_VALUE(x) ((x) << 0)
+#define	ATMEGA_OTGTCON_PAGE(x) ((x) << 5)
+
 #define	ATMEGA_UEINT 0xF4
 #define	ATMEGA_UEINT_MASK(n) (1 << (n))	/* endpoint interrupt mask */
 
@@ -136,8 +140,19 @@
 #define	ATMEGA_UDCON_LSM (1 << 2)
 #define	ATMEGA_UDCON_RSTCPU (1 << 3)
 
+#define	ATMEGA_OTGINT 0xDF
+
+#define	ATMEGA_OTGCON 0xDD
+#define	ATMEGA_OTGCON_VBUSRQC (1 << 0)
+#define	ATMEGA_OTGCON_VBUSREQ (1 << 1)
+#define	ATMEGA_OTGCON_VBUSHWC (1 << 2)
+#define	ATMEGA_OTGCON_SRPSEL (1 << 3)
+#define	ATMEGA_OTGCON_SRPREQ (1 << 4)
+#define	ATMEGA_OTGCON_HNPREQ (1 << 5)
+
 #define	ATMEGA_USBINT 0xDA
 #define	ATMEGA_USBINT_VBUSTI (1 << 0)	/* USB VBUS interrupt */
+#define	ATMEGA_USBINT_IDI (1 << 1)	/* USB ID interrupt */
 
 #define	ATMEGA_USBSTA 0xD9
 #define	ATMEGA_USBSTA_VBUS (1 << 0)
@@ -145,6 +160,7 @@
 
 #define	ATMEGA_USBCON 0xD8
 #define	ATMEGA_USBCON_VBUSTE (1 << 0)
+#define	ATMEGA_USBCON_IDE (1 << 1)
 #define	ATMEGA_USBCON_OTGPADE (1 << 4)
 #define	ATMEGA_USBCON_FRZCLK (1 << 5)
 #define	ATMEGA_USBCON_USBE (1 << 7)