svn commit: r308750 - in head/sys/dev: ic uart

[Ruslan Bukin]

Author: br
Date: Thu Nov 17 14:41:22 2016
New Revision: 308750
URL: https://svnweb.freebsd.org/changeset/base/308750

Log:
  Add support for UART found in the Ingenic XBurst system on chips.
  
  These CPUs has non-standard UART enable bit hidden in the UART FIFO
  Control Register.
  
  Sponsored by:	DARPA, AFRL

Modified:
  head/sys/dev/ic/ns16550.h
  head/sys/dev/uart/uart_dev_ns8250.c

Modified: head/sys/dev/ic/ns16550.h
==============================================================================
--- head/sys/dev/ic/ns16550.h	Thu Nov 17 14:32:23 2016	(r308749)
+++ head/sys/dev/ic/ns16550.h	Thu Nov 17 14:41:22 2016	(r308750)
@@ -156,6 +156,9 @@
 #define	FIFO_XMT_RST	FCR_XMT_RST
 #define	FCR_DMA		0x08
 #define	FIFO_DMA_MODE	FCR_DMA
+#ifdef CPU_XBURST
+#define	FCR_UART_ON	0x10
+#endif
 #define	FCR_RX_LOW	0x00
 #define	FIFO_RX_LOW	FCR_RX_LOW
 #define	FCR_RX_MEDL	0x40

Modified: head/sys/dev/uart/uart_dev_ns8250.c
==============================================================================
--- head/sys/dev/uart/uart_dev_ns8250.c	Thu Nov 17 14:32:23 2016	(r308749)
+++ head/sys/dev/uart/uart_dev_ns8250.c	Thu Nov 17 14:41:22 2016	(r308750)
@@ -198,6 +198,9 @@ ns8250_flush(struct uart_bas *bas, int w
 	uint8_t fcr;
 
 	fcr = FCR_ENABLE;
+#ifdef CPU_XBURST
+	fcr |= FCR_UART_ON;
+#endif
 	if (what & UART_FLUSH_TRANSMITTER)
 		fcr |= FCR_XMT_RST;
 	if (what & UART_FLUSH_RECEIVER)
@@ -268,6 +271,10 @@ ns8250_probe(struct uart_bas *bas)
 {
 	u_char val;
 
+#ifdef CPU_XBURST
+	uart_setreg(bas, REG_FCR, FCR_UART_ON);
+#endif
+
 	/* Check known 0 bits that don't depend on DLAB. */
 	val = uart_getreg(bas, REG_IIR);
 	if (val & 0x30)
@@ -289,7 +296,7 @@ static void
 ns8250_init(struct uart_bas *bas, int baudrate, int databits, int stopbits,
     int parity)
 {
-	u_char	ier;
+	u_char ier, val;
 
 	if (bas->rclk == 0)
 		bas->rclk = DEFAULT_RCLK;
@@ -306,7 +313,11 @@ ns8250_init(struct uart_bas *bas, int ba
 	uart_barrier(bas);
 
 	/* Disable the FIFO (if present). */
-	uart_setreg(bas, REG_FCR, 0);
+	val = 0;
+#ifdef CPU_XBURST
+	val = FCR_UART_ON;
+#endif
+	uart_setreg(bas, REG_FCR, val);
 	uart_barrier(bas);
 
 	/* Set RTS & DTR. */
@@ -461,6 +472,9 @@ ns8250_bus_attach(struct uart_softc *sc)
 
 	ns8250->mcr = uart_getreg(bas, REG_MCR);
 	ns8250->fcr = FCR_ENABLE;
+#ifdef CPU_XBURST
+	ns8250->fcr |= FCR_UART_ON;
+#endif
 	if (!resource_int_value("uart", device_get_unit(sc->sc_dev), "flags",
 	    &ivar)) {
 		if (UART_FLAGS_FCR_RX_LOW(ivar)) 
@@ -753,6 +767,7 @@ ns8250_bus_probe(struct uart_softc *sc)
 	struct uart_bas *bas;
 	int count, delay, error, limit;
 	uint8_t lsr, mcr, ier;
+	uint8_t val;
 
 	ns8250 = (struct ns8250_softc *)sc;
 	bas = &sc->sc_bas;
@@ -786,7 +801,11 @@ ns8250_bus_probe(struct uart_softc *sc)
 	 * done. Since this is the first time we enable the FIFOs, we reset
 	 * them.
 	 */
-	uart_setreg(bas, REG_FCR, FCR_ENABLE);
+	val = FCR_ENABLE;
+#ifdef CPU_XBURST
+	val |= FCR_UART_ON;
+#endif
+	uart_setreg(bas, REG_FCR, val);
 	uart_barrier(bas);
 	if (!(uart_getreg(bas, REG_IIR) & IIR_FIFO_MASK)) {
 		/*
@@ -800,7 +819,11 @@ ns8250_bus_probe(struct uart_softc *sc)
 		return (0);
 	}
 
-	uart_setreg(bas, REG_FCR, FCR_ENABLE | FCR_XMT_RST | FCR_RCV_RST);
+	val = FCR_ENABLE | FCR_XMT_RST | FCR_RCV_RST;
+#ifdef CPU_XBURST
+	val |= FCR_UART_ON;
+#endif
+	uart_setreg(bas, REG_FCR, val);
 	uart_barrier(bas);
 
 	count = 0;
@@ -810,7 +833,11 @@ ns8250_bus_probe(struct uart_softc *sc)
 	error = ns8250_drain(bas, UART_DRAIN_RECEIVER|UART_DRAIN_TRANSMITTER);
 	if (error) {
 		uart_setreg(bas, REG_MCR, mcr);
-		uart_setreg(bas, REG_FCR, 0);
+		val = 0;
+#ifdef CPU_XBURST
+		val |= FCR_UART_ON;
+#endif
+		uart_setreg(bas, REG_FCR, val);
 		uart_barrier(bas);
 		goto describe;
 	}
@@ -840,7 +867,11 @@ ns8250_bus_probe(struct uart_softc *sc)
 			ier = uart_getreg(bas, REG_IER) & ns8250->ier_mask;
 			uart_setreg(bas, REG_IER, ier);
 			uart_setreg(bas, REG_MCR, mcr);
-			uart_setreg(bas, REG_FCR, 0);
+			val = 0;
+#ifdef CPU_XBURST
+			val |= FCR_UART_ON;
+#endif
+			uart_setreg(bas, REG_FCR, val);
 			uart_barrier(bas);
 			count = 0;
 			goto describe;