CAMBRIA and more than one atheros card
John Hay
jhay at meraka.org.za
Mon Jul 14 19:09:49 UTC 2014
On Mon, Jul 14, 2014 at 12:06:34PM -0700, Adrian Chadd wrote:
> .. why's it need bounce buffers?
I found this:
arm/xscale/ixp425/ixp425_pci.c: /* NB: PCI dma window is 64M so anything above must be bounced */
John
>
>
> -a
>
>
> On 14 July 2014 11:42, John Hay <jhay at meraka.org.za> wrote:
> > On Mon, Jul 14, 2014 at 09:48:56AM -0700, Adrian Chadd wrote:
> >> Hm, it could be some bus related stupidity. It's allocating 2k or 4k
> >> mbufs for the receive path because wifi frames are bigger than
> >> ethernet frames. If you're not seeing failures in 4k mbuf allocations
> >> then I'm not sure what it could be.
> >>
> >> I'll see about firing it up locally and checking.
> >
> > I'm hunting a bit more and it looks like the fail is in the bounce pages.
> > It looks like the calls look like this:
> >
> > ath_legacy_rxbuf_init()
> > bus_dmamap_load_mbuf_sg()
> > _bus_dmamap_load_buffer()
> > _bus_dmamap_reserve_pages()
> > reserve_bounce_pages()
> >
> > I have added a printf at the start of alloc_bounce_pages() and it seems
> > that it is only called (twice) when ath0 is probed. Is bus_dma_tag_t dmat,
> > the first argument to alloc_bounce_pages(), common for the whole pci bus?
> >
> > The start of the boot, with my printf looks like this:
> >
> > ####################
> > FreeBSD ARM (Gateworks Cambria) boot2 v0.4
> > -
> > Default: /boot/kernel/kernel
> > boot:
> > Copyright (c) 1992-2014 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> > The Regents of the University of California. All rights reserved.
> > FreeBSD is a registered trademark of The FreeBSD Foundation.
> > FreeBSD 11.0-CURRENT #9 r268502M: Mon Jul 14 15:30:15 SAST 2014
> > jhay at dolphin.meraka.csir.co.za:/usr/obj/arm.armeb/snaps/arm/11-tst/src/sys/S
> > MALL-CAMBRIA arm
> > gcc version 4.2.1 20070831 patched [FreeBSD]
> > CPU: IXP435 rev 1 (ARMv5TE) (XScale core)
> > Big-endian DC enabled IC enabled WB enabled LABT branch prediction enabled
> > 32KB/32B 32-way instruction cache
> > 32KB/32B 32-way write-back-locking data cache
> > real memory = 134213632 (127 MB)
> > avail memory = 124440576 (118 MB)
> > random device not loaded; using insecure entropy
> > wlan: mac acl policy registered
> > random: <Software, Yarrow> initialized
> > ixp0: <Intel IXP4XX>
> > ixp0: 37e7f<RCOMP,USB,HASH,AES,DES,HDLC,AAL,ETH0,ETH1,PCI>
> > pcib0: <IXP4XX PCI Bus> on ixp0
> > pci0: <PCI bus> on pcib0
> > ath0: <Atheros 9220> irq 28 at device 1.0 on pci0
> > alloc_bounce_pages: numpages 63
> > [ath] enabling AN_TOP2_FIXUP
> > alloc_bounce_pages: numpages 1
> > ath0: AR9220 mac 128.2 RF5133 phy 13.0
> > ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
> > ath1: <Atheros 9220> irq 27 at device 2.0 on pci0
> > [ath] enabling AN_TOP2_FIXUP
> > ath1: AR9220 mac 128.2 RF5133 phy 13.0
> > ath1: 2GHz radio: 0x0000; 5GHz radio: 0x00c0
> > ath2: <Atheros 5413> irq 26 at device 3.0 on pci0
> > ath2: AR5413 mac 10.5 RF5413 phy 6.1
> > ath2: 2GHz radio: 0x0000; 5GHz radio: 0x0063
> > ixpclk0: <IXP4XX Timer> on ixp0
> > ####################
> >
> > Interesting, with this boot, with the new kernel, the aths did not fail.
> > Could the printf have changed something or was it just coincidence? With
> > a reboot ath1 and ath2 failed again during configuration and a little
> > while later ath0 started to complain:
> >
> > ath0: ath_rx_proc: no mbuf!
> >
> > John
> >
> >>
> >>
> >>
> >>
> >> -a
> >>
> >> On 14 July 2014 01:07, John Hay <jhay at meraka.org.za> wrote:
> >> > On Thu, Jul 10, 2014 at 06:02:27AM +0200, John Hay wrote:
> >> >> On Wed, Jul 09, 2014 at 06:46:12AM +0200, John Hay wrote:
> >> >> > Hi Guys,
> >> >> >
> >> >> > The problem is back / still there. I initially saw the problem during
> >> >> > boot, with the interface configs in rc.conf, but because it is so
> >> >> > mixed with the rest, I took it out and put it in the script, then
> >> >> > after multi-user boot was finished, I did a login and ran the script,
> >> >> > with the output I showed in the initial post.
> >> >> >
> >> >> > So I put the interface configs back into rc.conf and I'm seeing the
> >> >> > same problem, here is a cut during boot:
> >> >> >
> >> >> > ###############
> >> >> > Starting file system checks:
> >> >> > /dev/ad0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
> >> >> > /dev/ad0s1a: clean, 93385 free (33 frags, 11669 blocks, 0.0% fragmentation)
> >> >> > Mounting local file systems:.
> >> >> > Writing entropy file:.
> >> >> > Setting hostname: tst-cambria-11.
> >> >> > wlan0: Ethernet address: 00:21:a4:35:70:42
> >> >> > wlan1: Ethernet address: 00:21:a4:35:6c:96
> >> >> > ath1: unable to start recv logic
> >> >> > wlan2: Ethernet address: 00:21:a4:32:38:c2
> >> >> > ath2: unable to start recv logic
> >> >> > ###############
> >> >> >
> >> >> > Looking at the vmstat -z output the 256 Bucket fail is much higher than
> >> >> > if I let it boot to multiuser and then configured the interfaces. It
> >> >> > was in the 6000, while now it is much higher:
> >> >> >
> >> >> > Without wlan configs in rc.conf, but configured afterwards:
> >> >> > 16 Bucket: 64, 0, 15, 300, 3139, 16, 0
> >> >> > 256 Bucket: 1024, 0, 31, 1, 592,6062, 0
> >> >> > vmem btag: 28, 0, 4496, 256, 4496, 32, 0
> >> >> >
> >> >> > With wlan configs in rc.conf:
> >> >> > 16 Bucket: 64, 0, 16, 299, 8611, 16, 0
> >> >> > 256 Bucket: 1024, 0, 26, 6, 773,16928, 0
> >> >> > vmem btag: 28, 0, 4405, 59, 4405, 30, 0
> >> >> >
> >> >> > Both of them boot from a ro compact-flash with md /etc and /var, but
> >> >> > they are small 4.3M and 2.1M. I have hacked in the use of tmpfs, but
> >> >> > that did not make a difference.
> >> >> >
> >> >
> >> > Friday I power cycled the board and it came up without an error. All 3
> >> > atheros cards configured in rc.conf. So I left it on for the weekend
> >> > and by this morning there was still no errors, so I rebooted it and
> >> > again saw the "ath1: unable to start recv logic" message for ath1 and
> >> > ath2. I power cycled it, but still get the error, so Friday was just
> >> > lucky with some timing thing, maybe if the card receive while it is
> >> > still configuring? Also if I leave the board booted in this state,
> >> > ath0 also start to give problems:
> >> >
> >> > #################
> >> > ath0: ath_rx_proc: no mbuf!
> >> > ath0: ath_rx_proc: no mbuf!
> >> > ...
> >> > ath0: device timeout
> >> > ath0: ath_reset: unable to start recv logic
> >> > ...
> >> > #################
> >> >
> >> > In anycase it seems that memory allocation problem. How do I figure out
> >> > where it is? "netstat -m" does not seem to point to an error. The mbuf
> >> > info in vmstat -z also look ok. It is only "256 Bucket" in vmstat -z
> >> > that point to an alloc failure. How do I figure out where that is and
> >> > how do I fix it or work around it?
> >> >
> >> > ###################
> >> > tst-11-arm:~ # netstat -m
> >> > 128/382/510 mbufs in use (current/cache/total)
> >> > 127/129/256/7654 mbuf clusters in use (current/cache/total/max)
> >> > 127/126 mbuf+clusters out of packet secondary zone in use (current/cache)
> >> > 0/0/0/3827 4k (page size) jumbo clusters in use (current/cache/total/max)
> >> > 0/0/0/1134 9k jumbo clusters in use (current/cache/total/max)
> >> > 0/0/0/637 16k jumbo clusters in use (current/cache/total/max)
> >> > 286K/353K/639K bytes allocated to network (current/cache/total)
> >> > 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters)
> >> > 0/0/0 requests for mbufs delayed (mbufs/clusters/mbuf+clusters)
> >> > 0/0/0 requests for jumbo clusters delayed (4k/9k/16k)
> >> > 0/0/0 requests for jumbo clusters denied (4k/9k/16k)
> >> > 0/3/1488 sfbufs in use (current/peak/max)
> >> > 0 requests for sfbufs denied
> >> > 0 requests for sfbufs delayed
> >> > 0 requests for I/O initiated by sendfile
> >> > tst-11-arm:~ # vmstat -z | grep mbuf
> >> > mbuf_packet: 256, 48990, 127, 126, 2294, 0, 0
> >> > mbuf: 256, 48990, 1, 256, 920, 0, 0
> >> > mbuf_cluster: 2048, 7654, 253, 3, 253, 0, 0
> >> > mbuf_jumbo_page: 4096, 3827, 0, 0, 0, 0, 0
> >> > mbuf_jumbo_9k: 9216, 1134, 0, 0, 0, 0, 0
> >> > mbuf_jumbo_16k: 16384, 637, 0, 0, 0, 0, 0
> >> > mbuf_ext_refcnt: 4, 0, 0, 504, 1, 0, 0
> >> > tst-11-arm:~ # vmstat -z | grep Bucket
> >> > 4 Bucket: 16, 0, 7, 497, 1565, 0, 0
> >> > 6 Bucket: 24, 0, 0, 0, 0, 0, 0
> >> > 8 Bucket: 32, 0, 3, 375, 83, 0, 0
> >> > 12 Bucket: 48, 0, 2, 334, 5, 0, 0
> >> > 16 Bucket: 64, 0, 14, 301, 43687, 16, 0
> >> > 32 Bucket: 128, 0, 7, 148, 196, 0, 0
> >> > 64 Bucket: 256, 0, 19, 56, 77, 0, 0
> >> > 128 Bucket: 512, 0, 16, 16, 48, 0, 0
> >> > 256 Bucket: 1024, 0, 29, 3, 1521,86738, 0
> >> > tst-11-arm:~ #
> >> > ###################
> >> >
> >> > Regards
> >> >
> >> > John
> >> > --
> >> > John Hay -- jhay at meraka.csir.co.za / jhay at meraka.org.za / jhay at FreeBSD.org
More information about the freebsd-wireless
mailing list