eGalax USB touchscreen issues
Mark Kane
mark at kane.mn
Thu May 20 17:44:45 UTC 2021
Hi,
I'm trying to get an eGalax USB touchscreen working on FreeBSD
13.0-RELEASE and several approaches have been unsuccessful.
1) uep(4) in evdev or native mode - uep.ko automatically loads and
attaches. X uses the respective evdev or egalax input driver however no
events are registered with `xinput --test` or evemu-record. [1] suggests
uep(4) is for older non-HID devices and the vendor reused the same
device IDs for newer HID devices, so a different driver may be correct
for this device. [1]
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=183032
ugen0.3: <eGalax Inc. USB TouchController> at usbus0
uep0: <eGalax Inc. USB TouchController, class 0/0, rev 1.10/1.00, addr
3> on usbus0
2) uhid(4) - With uep(4) disabled, uhid(4) attempts to attach but fails:
kernel: ugen0.3: <eGalax Inc. USB TouchController> at usbus0
kernel: uhid1 on uhub1
kernel: uhid1: <eGalax Inc. USB TouchController, class 0/0, rev
1.10/1.00, addr 3> on usbus0
kernel: uhid1: no report descriptor
kernel: device_attach: uhid1 attach returned 12
3) uhidd(8) - With uhid(4) disabled, this is the only method that any
touchscreen events have been seen but there are issues. Sometimes
starting uhidd will fail the first couple times
("libusb20_dev_request_sync failed" the first, crash the second) and
then start OK after a few tries. When it is running uhidd prints
touchscreen events with -v but X didn't autodetect the /dev/uvhid*
device or if symlinked to /dev/uhid*. If the X "mouse" driver is
configured with the uvhid device X will segfault upon startup citing
mouse_drv.so.
4) wmt(4) - wmt.ko automatically loads but does not attach or create any
evdev devices.
5) `webcamd -l` shows the device but exits on startup with "Cannot find
USB device".
Should this device work with uhid(4) or wmt(4) and does the below output
give any clues what might be going wrong? If uhidd(8) or webcamd is what
should be used instead are there any issues with my config?
The device itself should be okay, it works out of the box on OpenBSD and
the vendor provides drivers for Linux.
Thanks in advance for any pointers.
-Mark
# usbconfig
ugen0.1: <Intel EHCI root HUB> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (0mA)
ugen0.2: <vendor 0x8087 product 0x07e6> at usbus0, cfg=0 md=HOST
spd=HIGH (480Mbps) pwr=SAVE (0mA)
ugen0.3: <eGalax Inc. USB TouchController> at usbus0, cfg=0 md=HOST
spd=FULL (12Mbps) pwr=ON (100mA)
ugen0.4: <Lite-On Technology Corp. USB Multimedia Keyboard> at usbus0,
cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA)
ugen0.5: <vendor 0x05e3 USB2.0 Hub> at usbus0, cfg=0 md=HOST spd=HIGH
(480Mbps) pwr=SAVE (100mA)
#
# usbhid-dump
000:003:000:DESCRIPTOR 1621478496.823720
8D 0F 00 09 42 09 32 15 00 25 01 95 02 75 01 81
02 95 06 75 01 81 03 05 01 09 30 75 10 95 01 A4
55 00 65 00 36 00 00 46 00 00 16 1E 00 26 C8 0F
81 02 09 31 16 3C 00 26
000:004:001:DESCRIPTOR 1621478496.826074
05 0C 09 01 A1 01 85 01 19 00 2A 3C 02 15 00 26
3C 02 95 01 75 10 81 00 C0 05 01 09 80 A1 01 85
02 19 81 29 83 25 01 75 01 95 03 81 02 95 05 81
01 C0
000:004:000:DESCRIPTOR 1621478496.829067
05 01 09 06 A1 01 05 07 19 E0 29 E7 15 00 25 01
95 08 75 01 81 02 95 08 75 01 81 01 05 08 19 01
29 03 95 03 75 01 91 02 95 01 75 05 91 01 05 07
19 00 2A FF 00 15 00 26 FF 00 95 06 75 08 81 00
C0
#
# usbconfig -d ugen0.3 dump_all_desc
ugen0.3: <eGalax Inc. USB TouchController> at usbus0, cfg=0 md=HOST
spd=FULL (12Mbps) pwr=ON (100mA)
bLength = 0x0012
bDescriptorType = 0x0001
bcdUSB = 0x0110
bDeviceClass = 0x0000 <Probed by interface class>
bDeviceSubClass = 0x0000
bDeviceProtocol = 0x0000
bMaxPacketSize0 = 0x0040
idVendor = 0x0eef
idProduct = 0x0001
bcdDevice = 0x0100
iManufacturer = 0x0001 <eGalax Inc.>
iProduct = 0x0002 <USB TouchController>
iSerialNumber = 0x0000 <no string>
bNumConfigurations = 0x0001
Configuration index 0
bLength = 0x0009
bDescriptorType = 0x0002
wTotalLength = 0x0022
bNumInterfaces = 0x0001
bConfigurationValue = 0x0001
iConfiguration = 0x0001 <eGalax Inc.>
bmAttributes = 0x00a0
bMaxPower = 0x0032
Interface 0
bLength = 0x0009
bDescriptorType = 0x0004
bInterfaceNumber = 0x0000
bAlternateSetting = 0x0000
bNumEndpoints = 0x0001
bInterfaceClass = 0x0003 <HID device>
bInterfaceSubClass = 0x0000
bInterfaceProtocol = 0x0000
iInterface = 0x0000 <no string>
Additional Descriptor
bLength = 0x09
bDescriptorType = 0x21
bDescriptorSubType = 0x10
RAW dump:
0x00 | 0x09, 0x21, 0x10, 0x02, 0x00, 0x01, 0x22, 0x8d,
0x08 | 0x00
Endpoint 0
bLength = 0x0007
bDescriptorType = 0x0005
bEndpointAddress = 0x0081 <IN>
bmAttributes = 0x0003 <INTERRUPT>
wMaxPacketSize = 0x0008
bInterval = 0x0003
bRefresh = 0x0000
bSynchAddress = 0x0000
#
-----------------------
uhidd sees events:
# /usr/local/sbin/uhidd -kmohsuvvv /dev/ugen0.3
uhidd 1292 - - open /usr/local/etc/uhidd.conf failed: No such file or
directory
uhidd 1292 - - proceed without configuration file
ugen0.3[0]-> HID interface
ugen0.3[0]-> Report descriptor size = 141
ugen0.3[0]-> Find IN interrupt ep: 0x81 packet_size=0x8
HID APPLICATION COLLECTION (Pointer) size(63)
HID REPORT: ID 1
INPUT:
POS:0 SIZE:1 COUNT:2 [VARIABLE]
USAGE Button1
USAGE Button2
POS:2 SIZE:6 COUNT:1 [CONST]
POS:8 SIZE:16 COUNT:2 [VARIABLE]
USAGE X
USAGE Y
HID APPLICATION COLLECTION (Touch Screen) size(78)
HID REPORT: ID 2
INPUT:
POS:0 SIZE:1 COUNT:2 [VARIABLE]
USAGE Tip Switch
USAGE In Range
POS:2 SIZE:1 COUNT:6 [CONST]
POS:8 SIZE:16 COUNT:1 [VARIABLE]
USAGE X
POS:24 SIZE:16 COUNT:1 [VARIABLE]
USAGE Y
uhidd 1292 - - cuse initiailzed.
ugen0.3[0]-> vhid device created: uvhid0
ugen0.3[0]-> vhid device created: uvhid1
ugen0.3[0]-> HID interface task started
[...start touching screen...]
ugen0.3[0]-> received data(6): 02 03 -7 03 -8 10
hid_appcol_recv_data: len(6) 0x02 0x03 0xf9 0x03 0xf8 0x0a
ugen0.3[0]-> uvhid1 received data: 2 3 249 3 248 10
ugen0.3[0]-> received data(6): 02 03 -7 03 -13 10
hid_appcol_recv_data: len(6) 0x02 0x03 0xf9 0x03 0xf3 0x0a
ugen0.3[0]-> uvhid1 received data: 2 3 249 3 243 10
ugen0.3[0]-> received data(6): 02 02 -7 03 -13 10
hid_appcol_recv_data: len(6) 0x02 0x02 0xf9 0x03 0xf3 0x0a
ugen0.3[0]-> uvhid1 received data: 2 2 249 3 243 10
ugen0.3[0]-> received data(6): 02 03 -30 03 00 11
hid_appcol_recv_data: len(6) 0x02 0x03 0xe2 0x03 0x00 0x0b
ugen0.3[0]-> uvhid1 received data: 2 3 226 3 0 11
ugen0.3[0]-> received data(6): 02 03 -39 03 09 11
[... more events ...]
#
however X crashes with uhidd and xf86-input-mouse:
[...]
[ 151.396] (II) Using input driver 'mouse' for 'Touch0'
[ 151.397] (**) Option "SendCoreEvents"
[ 151.397] (**) Option "CorePointer" "on"
[ 151.397] (**) Touch0: always reports core events
[ 151.397] (**) Option "Protocol" "usb"
[ 151.397] (**) Option "Device" "/dev/uvhid1"
[ 151.397] (**) Touch0: Protocol: usb
[ 151.397] (**) Touch0: always reports core events
[ 151.397] (==) Touch0: Opening new HID device
[ 151.398] (==) Touch0: Found 1 usable logical collections
[ 151.398] (**) Option "Collection" "2"
[ 151.398] (**) Touch0: Collection: 2
[ 151.398] (EE) Touch0: Application collection not found or already
handled
[ 151.398] (**) Touch0: Protocol: "usb"
[ 151.398] (II) XINPUT: Adding extended input device "Touch0" (type:
MOUSE, id 7)
[ 151.399] (EE)
[ 151.399] (EE) Backtrace:
[ 151.402] (EE) 0: /usr/local/bin/Xorg (?+0x0) [0x41dd9a]
[ 151.404] (EE) unw_get_proc_name failed: no unwind info found [-10]
[ 151.404] (EE) 1: /lib/libthr.so.3 (?+0x0) [0x800928e0e]
[ 151.407] (EE) unw_get_proc_name failed: no unwind info found [-10]
[ 151.407] (EE) 2: /lib/libthr.so.3 (?+0x0) [0x8009283cf]
[ 151.409] (EE) 3: ? (?+0x0) [0x7ffffffff003]
[ 151.412] (EE) 4: /usr/local/lib/xorg/modules/input/mouse_drv.so
(?+0x0) [0x801cef5ff]
[ 151.415] (EE) 5: /usr/local/bin/Xorg (?+0x0) [0x292bfc]
[ 151.417] (EE) 6: /usr/local/bin/Xorg (?+0x0) [0x2f0ed8]
[ 151.420] (EE) 7: /usr/local/bin/Xorg (?+0x0) [0x2e6961]
[ 151.422] (EE) 8: /usr/local/bin/Xorg (?+0x0) [0x2a1a5f]
[ 151.425] (EE) 9: /usr/local/bin/Xorg (?+0x0) [0x28a420]
[ 151.427] (EE) 10: ? (?+0x0) [0x800458008]
[ 151.427] (EE)
[ 151.427] (EE) Segmentation fault at address 0x0
[ 151.428] (EE)
Fatal server error:
[ 151.428] (EE) Caught signal 11 (Segmentation fault). Server aborting
Section "InputDevice"
Identifier "Touch0"
Driver "mouse"
Option "Protocol" "usb"
Option "Device" "/dev/uvhid1"
EndSection
Sometimes uhidd has problems starting but then works on the 3rd or 4th
try:
# uhidd -dD -vvv -kmohu /dev/ugen0.3
uhidd 1808 - - open /usr/local/etc/uhidd.conf failed: No such file or
directory
uhidd 1808 - - proceed without configuration file
ugen0.3[0]-> HID interface
ugen0.3[0]-> Report descriptor size = 141
uhidd 1808 - - ugen0.3[0]=> libusb20_dev_request_sync failed
# uhidd -dD -vvv -kmohu /dev/ugen0.3
uhidd 1809 - - open /usr/local/etc/uhidd.conf failed: No such file or
directory
uhidd 1809 - - proceed without configuration file
ugen0.3[0]-> HID interface
ugen0.3[0]-> Report descriptor size = 141
ugen0.3[0]-> Report descriptor dump:
illegal type (bType=3)
illegal Main Item (bTag=0)
ugen0.3[0]-> Find IN interrupt ep: 0x81 packet_size=0x8
uhidd: hid_parser: unknown bType(3)
uhidd: hid_parser: unknown Main item(0)
Assertion failed: (ha != NULL), function hid_parser_init, file
uhidd_hidcore.c, line 380.
Abort (core dumped)
# uhidd -dD -vvv -kmohu /dev/ugen0.3
uhidd 1810 - - open /usr/local/etc/uhidd.conf failed: No such file or
directory
uhidd 1810 - - proceed without configuration file
ugen0.3[0]-> HID interface
ugen0.3[0]-> Report descriptor size = 141
uhidd 1810 - - ugen0.3[0]=> libusb20_dev_request_sync failed
# uhidd -dD -vvv -kmohu /dev/ugen0.3
uhidd 1811 - - open /usr/local/etc/uhidd.conf failed: No such file or
directory
uhidd 1811 - - proceed without configuration file
ugen0.3[0]-> HID interface
ugen0.3[0]-> Report descriptor size = 141
ugen0.3[0]-> Report descriptor dump:
USAGE PAGE Generic Desktop(0x1)
USAGE Pointer(0x1)[Generic Desktop(0x1)]
COLLECTION Application(1)
REPORT ID 1
USAGE Pointer(0x1)[Generic Desktop(0x1)]
COLLECTION Physical(0)
USAGE PAGE Button(0x9)
USAGE MINIMUM Button1(1)
USAGE MAXIMUM Button2(2)
LOGICAL MINIMUM 0
LOGICAL MAXIMUM 1
REPORT COUNT 2
REPORT SIZE 1
INPUT ( Data Variable Absolute ) (2)
REPORT COUNT 1
REPORT SIZE 6
INPUT ( Const Array Absolute ) (1)
USAGE PAGE Generic Desktop(0x1)
USAGE X(0x30)[Generic Desktop(0x1)]
USAGE Y(0x31)[Generic Desktop(0x1)]
LOGICAL MINIMUM 42
LOGICAL MAXIMUM 1981
PHYSICAL MINIMUM 0
PHYSICAL MAXIMUM 4095
UNIT (0)
REPORT SIZE 16
REPORT COUNT 2
INPUT ( Data Variable Absolute ) (2)
END COLLECTION
END COLLECTION
USAGE PAGE Digitizer(0xd)
USAGE Touch Screen(0x4)[Digitizer(0xd)]
COLLECTION Application(1)
REPORT ID 2
USAGE Stylus(0x20)[Digitizer(0xd)]
COLLECTION Physical(0)
USAGE Tip Switch(0x42)[Digitizer(0xd)]
USAGE In Range(0x32)[Digitizer(0xd)]
LOGICAL MINIMUM 0
LOGICAL MAXIMUM 1
REPORT COUNT 2
REPORT SIZE 1
INPUT ( Data Variable Absolute ) (2)
REPORT COUNT 6
REPORT SIZE 1
INPUT ( Const Variable Absolute ) (3)
USAGE PAGE Generic Desktop(0x1)
USAGE X(0x30)[Generic Desktop(0x1)]
REPORT SIZE 16
REPORT COUNT 1
PUSH
UNIT EXPONENT 0
UNIT (0)
PHYSICAL MINIMUM 0
PHYSICAL MAXIMUM 0
LOGICAL MINIMUM 30
LOGICAL MAXIMUM 4040
INPUT ( Data Variable Absolute ) (2)
USAGE Y(0x31)[Generic Desktop(0x1)]
LOGICAL MINIMUM 60
LOGICAL MAXIMUM 4035
PHYSICAL MINIMUM 0
PHYSICAL MAXIMUM 0
INPUT ( Data Variable Absolute ) (2)
POP
END COLLECTION
END COLLECTION
ugen0.3[0]-> Find IN interrupt ep: 0x81 packet_size=0x8
HID APPLICATION COLLECTION (Pointer) size(63)
HID REPORT: ID 1
INPUT:
POS:0 SIZE:1 COUNT:2 [VARIABLE]
USAGE Button1
USAGE Button2
POS:2 SIZE:6 COUNT:1 [CONST]
POS:8 SIZE:16 COUNT:2 [VARIABLE]
USAGE X
USAGE Y
HID APPLICATION COLLECTION (Touch Screen) size(78)
HID REPORT: ID 2
INPUT:
POS:0 SIZE:1 COUNT:2 [VARIABLE]
USAGE Tip Switch
USAGE In Range
POS:2 SIZE:1 COUNT:6 [CONST]
POS:8 SIZE:16 COUNT:1 [VARIABLE]
USAGE X
POS:24 SIZE:16 COUNT:1 [VARIABLE]
USAGE Y
ugen0.3[0]-> Kernel driver is active
ugen0.3[0]-> kernel driver detached!
uhidd 1811 - - Attempt to load kernel module cuse.ko...
uhidd 1811 - - Successfully loaded cuse kernel module
uhidd 1811 - - cuse initiailzed.
ugen0.3[0]-> vhid device created: uvhid0
ugen0.3[0]-> vhid device created: uvhid1
ugen0.3[0]-> HID interface task started
-----------------------
# webcamd -d ugen0.3
webcamd 1415 - - Attached to ugen0.3[0]
webcamd 1415 - - webcamd: Cannot find USB device
#
-----------------------
uep(4) with evdev:
# evemu-describe
Available devices:
/dev/input/event0: System mouse
/dev/input/event1: System keyboard multiplexer
/dev/input/event2: Power Button
/dev/input/event3: Sleep Button
/dev/input/event4: Lite-On Technology Corp. USB Multimedia Keyboard,
class 0/0, rev 1.10/1.09, add
/dev/input/event5: eGalax Inc. USB TouchController, class 0/0, rev
1.10/1.00, addr 3
Select the device event number [0-5]: 5
# EVEMU 1.3
# Kernel: 13.0-RELEASE
# Input device name: "eGalax Inc. USB TouchController, class 0/0, rev
1.10/1.00, addr 3"
# Input device ID: bus 0x03 vendor 0xeef product 0x01 version 0000
# Supported events:
# Event type 0 (EV_SYN)
# Event code 0 (SYN_REPORT)
# Event code 1 (SYN_CONFIG)
# Event code 2 (SYN_MT_REPORT)
# Event code 3 (SYN_DROPPED)
# Event code 4 ((null))
# Event code 5 ((null))
# Event code 6 ((null))
# Event code 7 ((null))
# Event code 8 ((null))
# Event code 9 ((null))
# Event code 10 ((null))
# Event code 11 ((null))
# Event code 12 ((null))
# Event code 13 ((null))
# Event code 14 ((null))
# Event code 15 (SYN_MAX)
# Event type 1 (EV_KEY)
# Event code 330 (BTN_TOUCH)
# Event type 3 (EV_ABS)
# Event code 0 (ABS_X)
# Value 0
# Min 0
# Max 2047
# Fuzz 0
# Flat 0
# Resolution 0
# Event code 1 (ABS_Y)
# Value 0
# Min 0
# Max 2047
# Fuzz 0
# Flat 0
# Resolution 0
# Properties:
# Property type 1 (INPUT_PROP_DIRECT)
N: eGalax Inc. USB TouchController, class 0/0, rev 1.10/1.00, addr 3
I: 0003 0eef 0001 0000
P: 02 00 00 00 00 00 00 00
B: 00 0b 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 04 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 01 00 00 00 00 00 00 00 00
B: 02 00 00 00 00 00 00 00 00
B: 03 03 00 00 00 00 00 00 00
B: 04 00 00 00 00 00 00 00 00
B: 05 00 00 00 00 00 00 00 00
B: 11 00 00 00 00 00 00 00 00
B: 12 00 00 00 00 00 00 00 00
B: 14 00 00 00 00 00 00 00 00
B: 15 00 00 00 00 00 00 00 00
B: 15 00 00 00 00 00 00 00 00
A: 00 0 2047 0 0 0
A: 01 0 2047 0 0 0
#
# libinput list-devices
[...]
Device: eGalax Inc. USB TouchController, class 0/0, rev
1.10/1.00, addr 3
Kernel: /dev/input/event5
Group: 6
Seat: seat0, default
Capabilities: touch
Tap-to-click: n/a
Tap-and-drag: n/a
Tap drag lock: n/a
Left-handed: n/a
Nat.scrolling: n/a
Middle emulation: n/a
Calibration: identity matrix
Scroll methods: none
Click methods: none
Disable-w-typing: n/a
Accel profiles: n/a
Rotation: n/a
#
X log for uep(4) in evdev mode:
[ 291.398] (II) config/udev: Adding input device eGalax Inc. USB
TouchController (/dev/input/event5)
[ 291.398] (**) eGalax Inc. USB TouchController: Applying InputClass
"evdev touchscreen catchall"
[ 291.398] (**) eGalax Inc. USB TouchController: Applying InputClass
"libinput touchscreen catchall"
[ 291.398] (II) Using input driver 'libinput' for 'eGalax Inc. USB
TouchController'
[ 291.398] (**) eGalax Inc. USB TouchController: always reports core
events
[ 291.398] (**) Option "Device" "/dev/input/event5"
[ 291.398] (**) Option "_source" "server/udev"
[ 291.401] (II) event5 - eGalax Inc. USB TouchController, class 0/0,
rev 1.10/1.00, addr 3: is tagged by udev as: Touchscreen
[ 291.402] (II) event5 - eGalax Inc. USB TouchController, class 0/0,
rev 1.10/1.00, addr 3: device is a touch device
[ 291.403] (II) event5 - eGalax Inc. USB TouchController, class 0/0,
rev 1.10/1.00, addr 3: device removed
[ 291.403] (**) Option "config_info" "udev:/dev/input/event5"
[ 291.403] (II) XINPUT: Adding extended input device "eGalax Inc. USB
TouchController" (type: TOUCHSCREEN, id 11)
[ 291.403] (**) Option "AccelerationScheme" "none"
[ 291.403] (**) eGalax Inc. USB TouchController: (accel) selected
scheme none/0
[ 291.403] (**) eGalax Inc. USB TouchController: (accel) acceleration
factor: 2.000
[ 291.403] (**) eGalax Inc. USB TouchController: (accel) acceleration
threshold: 4
[ 291.406] (II) event5 - eGalax Inc. USB TouchController, class 0/0,
rev 1.10/1.00, addr 3: is tagged by udev as: Touchscreen
[ 291.407] (II) event5 - eGalax Inc. USB TouchController, class 0/0,
rev 1.10/1.00, addr 3: device is a touch device
xinput uep(4) evdev test:
% xinput --list
⎡ Virtual core pointer id=2 [master pointer (3)]
⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer
(2)]
⎜ ↳ System mouse id=6 [slave pointer
(2)]
⎜ ↳ eGalax Inc. USB TouchController id=11 [slave pointer
(2)]
⎣ Virtual core keyboard id=3 [master keyboard (2)]
↳ Virtual core XTEST keyboard id=5 [slave keyboard
(3)]
↳ System keyboard multiplexer id=7 [slave keyboard
(3)]
↳ Power Button id=8 [slave keyboard
(3)]
↳ Sleep Button id=9 [slave keyboard
(3)]
↳ Lite-On Technology Corp. USB Multimedia Keyboard id=10 [slave
keyboard (3)]
% xinput --test 11
[...no events...]
^C
%
dmesg:
Copyright (c) 1992-2021 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-RELEASE #0 releng/13.0-n244733-ea31abc261f: Fri Apr 9
04:24:09 UTC 2021
root at releng1.nyi.freebsd.org:/usr/obj/usr/src/amd64.amd64/sys/GENERIC
amd64
FreeBSD clang version 11.0.1 (git at github.com:llvm/llvm-project.git
llvmorg-11.0.1-0-g43ff75f2c3fe)
VT(vga): resolution 640x480
CPU: Intel(R) Atom(TM) CPU E3845 @ 1.91GHz (1916.71-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x30679 Family=0x6 Model=0x37 Stepping=9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x43d8e3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,RDRAND>
AMD Features=0x28000800<SYSCALL,RDTSCP,LM>
AMD Features2=0x101<LAHF,Prefetch>
Structured Extended Features=0x2282<TSCADJ,SMEP,ERMS,NFPUSG>
VT-x: (disabled in BIOS) PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 2147483648 (2048 MB)
avail memory = 1907458048 (1819 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I >
WARNING: L1 data cache covers fewer APIC IDs than a core (0 < 1)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
random: unblocking device.
Firmware Warning (ACPI): 32/64X length mismatch in FADT/Gpe0Block:
128/32 (20201113/tbfadt-748)
ioapic0 <Version 2.0> irqs 0-86
Launching APs: 3 2 1
Timecounter "TSC" frequency 1916713993 Hz quality 1000
KTLS: Initialized 4 threads
random: entropy device external interface
000.000019 [4354] netmap_init netmap: loaded module
[ath_hal] loaded
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD
14.0.
kbd0 at kbdmux0
mlx5en: Mellanox Ethernet driver 3.6.0 (December 2020)
nexus0
vtvga0: <VT VGA driver>
cryptosoft0: <software crypto>
aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS>
acpi0: <ALASKA A M I >
acpi0: Power Button (fixed)
unknown: I/O range not supported
cpu0: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 on acpi0
atrtc0: Warning: Couldn't map I/O.
atrtc0: registered as a time-of-day clock, resolution 1.000000s
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 8 on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: Length mismatch for 3 range: 50d06fff vs 50d07000
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xe080-0xe087 mem
0xd0000000-0xd03fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
vgapci0: Boot video device
ahci0: <AHCI SATA controller> port
0xe070-0xe077,0xe060-0xe063,0xe050-0xe057,0xe040-0xe043,0xe020-0xe03f
mem 0xd0d06000-0xd0d067ff irq 19 at device 19.0 on pci0
ahci0: AHCI v1.30 with 2 3Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
pci0: <encrypt/decrypt> at device 26.0 (no driver attached)
hdac0: <Intel BayTrail HDA Controller> mem 0xd0d00000-0xd0d03fff irq 22
at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
igb0: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0xd000-0xd01f
mem 0xd0a00000-0xd0afffff,0xd0b00000-0xd0b03fff irq 16 at device 0.0 on
pci1
igb0: Using 1024 TX descriptors and 1024 RX descriptors
igb0: Using 4 RX queues 4 TX queues
igb0: Using MSI-X interrupts with 5 vectors
igb0: Ethernet address: 00:10:f3:9c:6b:7c
igb0: netmap queues/slots: TX 4/1024, RX 4/1024
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci2: <ACPI PCI bus> on pcib3
pci2: <simple comms, UART> at device 0.0 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib4
igb1: <Intel(R) PRO/1000 PCI-Express Network Driver> port 0xc000-0xc01f
mem 0xd0700000-0xd07fffff,0xd0800000-0xd0803fff irq 19 at device 0.0 on
pci3
igb1: Using 1024 TX descriptors and 1024 RX descriptors
igb1: Using 4 RX queues 4 TX queues
igb1: Using MSI-X interrupts with 5 vectors
igb1: Ethernet address: 00:10:f3:9c:6b:7d
igb1: netmap queues/slots: TX 4/1024, RX 4/1024
ehci0: <Intel BayTrail USB 2.0 controller> mem 0xd0d05000-0xd0d053ff irq
23 at device 29.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
usbus0: 480Mbps High Speed USB v2.0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
ppc1: <Parallel port> port 0x378-0x37f irq 15 on acpi0
ppc1: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart2: <16950 or compatible> port 0x248-0x24f irq 5 on acpi0
uart1: <16950 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart3: <16950 or compatible> port 0x3e8-0x3ef irq 11 on acpi0
uart4: <16950 or compatible> port 0x2e8-0x2ef irq 10 on acpi0
uart5: <16950 or compatible> port 0x228-0x22f irq 6 on acpi0
uart6: <16950 or compatible> port 0x238-0x23f irq 7 on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC888 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC888 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC888 (Rear Analog)> at nid 20 and 24 on hdaa0
pcm1: <Realtek ALC888 (Analog)> at nid 21 and 26 on hdaa0
hdacc1: <Intel Valleyview2 HDA CODEC> at cad 2 on hdac0
hdaa1: <Intel Valleyview2 Audio Function Group> at nid 1 on hdacc1
hdaa1: hdaa_audio_as_parse: Duplicate pin 0 (5) in association 1!
Disabling association.
hdaa1: hdaa_audio_as_parse: Duplicate pin 0 (6) in association 1!
Disabling association.
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <KINGSTON SA400S37120G SBFKB1E1> ACS-3 ATA SATA 3.x device
ada0: Serial Number 50026B768365A54C
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 512bytes)
ada0: Command Queueing enabled
ada0: 114473MB (234441648 512 byte sectors)
Trying to mount root from ufs:/dev/ada0s1a [rw]...
ugen0.1: <Intel EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ichsmb0: <Intel Baytrail SMBus controller> port 0xe000-0xe01f mem
0xd0d04000-0xd0d0401f irq 18 at device 31.3 on pci0
smbus0: <System Management Bus> on ichsmb0
lo0: link state changed to UP
uhub0: 8 ports with 8 removable, self powered
ugen0.2: <vendor 0x8087 product 0x07e6> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x8087 product 0x07e6, class 9/0, rev 2.00/0.17, addr 2>
on usbus0
uhub1: 4 ports with 4 removable, self powered
igb1: link state changed to UP
ugen0.3: <eGalax Inc. USB TouchController> at usbus0
ugen0.4: <Lite-On Technology Corp. USB Multimedia Keyboard> at usbus0
ukbd0 on uhub1
ukbd0: <Lite-On Technology Corp. USB Multimedia Keyboard, class 0/0, rev
1.10/1.09, addr 4> on usbus0
kbd1 at ukbd0
ugen0.5: <vendor 0x05e3 USB2.0 Hub> at usbus0
uhub2 on uhub1
uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr 5> on
usbus0
uhub2: 4 ports with 4 removable, self powered
More information about the freebsd-usb
mailing list