urndis and umodem device collision for ue device

[Randall Fox]

On Mon, Dec 22, 2014 at 1:23 AM, Hans Petter Selasky <hps at selasky.org>
wrote:

> On 12/22/14 10:14, Randall Fox wrote:
>
>> On Mon, Dec 22, 2014 at 12:42 AM, Hans Petter Selasky <hps at selasky.org>
>> wrote:
>>
>>  On 12/21/14 22:28, Randall Fox wrote:
>>>
>>>  On Sun, Dec 21, 2014 at 1:02 PM, Hans Petter Selasky <hps at selasky.org>
>>>> wrote:
>>>>
>>>>   On 12/21/14 21:40, Randall Fox wrote:
>>>>
>>>>>
>>>>>   Did you update /etc/devd/usb.conf, install new kernel and reboot your
>>>>>
>>>>>>
>>>>>>
>>>>>>>   system?
>>>>>>>
>>>>>>
>>>>>> I actually had the FreeNAS team apply this fix to the nightly build
>>>>>> and
>>>>>> I
>>>>>> created a whole new install based on their Nightly Build.  The DEVs
>>>>>> put
>>>>>> the
>>>>>> fix in, and it must have been correct because it worked for someone
>>>>>> else.
>>>>>>
>>>>>> Here is the link to the ticket for this:
>>>>>> https://bugs.freenas.org/issues/7153
>>>>>> It appears they are familiar with you!
>>>>>>
>>>>>> I will try putting the usb.conf in the location you specify, to see if
>>>>>> that
>>>>>> works.  I would be surprised if the dev's missed this.
>>>>>>
>>>>>>
>>>>>>
>>>>>> On Sun, Dec 21, 2014 at 12:24 PM, Hans Petter Selasky <
>>>>>> hps at selasky.org>
>>>>>> wrote:
>>>>>>
>>>>>>    On 12/21/14 21:21, Randall Fox wrote:
>>>>>>
>>>>>>
>>>>>>>    Hi,
>>>>>>>
>>>>>>>
>>>>>>>>
>>>>>>>>  The following patches should fix your problem:
>>>>>>>>>
>>>>>>>>> https://svnweb.freebsd.org/changeset/base/275790
>>>>>>>>> https://svnweb.freebsd.org/changeset/base/275791
>>>>>>>>>
>>>>>>>>> --HPS
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>   Can you get the dmesg when plugging your device?
>>>>>>>>
>>>>>>>
>>>>> --HPS
>>>>>
>>>>>
>>>>>   uhid0: <Tripp Lite TRIPP LITE SMART1500RM2U, class 0/0, rev
>>>>> 1.10/2.0a,
>>>>>
>>>> addr 3> on usbus1
>>>> ugen1.3: <Tripp Lite> at usbus1 (disconnected)
>>>> uhid0: at uhub3, port 1, addr 3 (disconnected)
>>>> ugen1.3: <Tripp Lite> at usbus1
>>>> uhid0: <Tripp Lite TRIPP LITE SMART1500RM2U, class 0/0, rev 1.10/2.0a,
>>>> addr 3> on usbus1
>>>> ugen1.3: <Tripp Lite> at usbus1 (disconnected)
>>>> uhid0: at uhub3, port 1, addr 3 (disconnected)
>>>>
>>>> I tried putting the usb.conf in /etc/devd and rebooting, but no change..
>>>>
>>>>
>>>>  Hi,
>>>
>>> This looks correct. Did you select the correct device profile?
>>>
>>> Also, did you set the correct USB configuration number?
>>>
>>> usbconfig -d X.Y dump_device_desc dump_curr_config_desc
>>> usbconfig -d X.Y set_config 1
>>>
>>> --HPS
>>>
>>>
>> I ran the set_config 1, but that didn't have any effect, nor did
>> set_config
>> 0.   the dump device & config is below.
>>
>> I did not select any profile, I just plug the unit in and I get the
>> disconnect messages.
>>
>> ugen1.3: <TRIPP LITE SMART1500RM2U Tripp Lite> at usbus1, cfg=0
>> md=HOST spd=LOW (1.5Mbps) pwr=ON (0mA)
>>
>>    bLength = 0x0012
>>    bDescriptorType = 0x0001
>>    bcdUSB = 0x0110
>>    bDeviceClass = 0x0000
>>    bDeviceSubClass = 0x0000
>>    bDeviceProtocol = 0x0000
>>    bMaxPacketSize0 = 0x0008
>>    idVendor = 0x09ae
>>    idProduct = 0x3015
>>    bcdDevice = 0x020a
>>    iManufacturer = 0x0002  <Tripp Lite >
>>    iProduct = 0x0003  <TRIPP LITE SMART1500RM2U >
>>    iSerialNumber = 0x0004  <2351BY0SM820600181>
>>    bNumConfigurations = 0x0001
>>
>>
>>   Configuration index 0
>>
>>      bLength = 0x0009
>>      bDescriptorType = 0x0002
>>      wTotalLength = 0x0022
>>      bNumInterfaces = 0x0001
>>      bConfigurationValue = 0x0001
>>      iConfiguration = 0x0000  <no string>
>>      bmAttributes = 0x00e0
>>      bMaxPower = 0x0000
>>
>>      Interface 0
>>        bLength = 0x0009
>>        bDescriptorType = 0x0004
>>        bInterfaceNumber = 0x0000
>>        bAlternateSetting = 0x0000
>>        bNumEndpoints = 0x0001
>>        bInterfaceClass = 0x0003
>>        bInterfaceSubClass = 0x0000
>>        bInterfaceProtocol = 0x0000
>>        iInterface = 0x0000  <no string>
>>
>>        Additional Descriptor
>>
>>        bLength = 0x09
>>        bDescriptorType = 0x21
>>        bDescriptorSubType = 0x10
>>         RAW dump:
>>         0x00 | 0x09, 0x21, 0x10, 0x01, 0x00, 0x01, 0x22, 0xe4,
>>         0x08 | 0x04
>>
>>        Endpoint 0
>>
>>        bLength = 0x0007
>>        bDescriptorType = 0x0005
>>        bEndpointAddress = 0x0081  <IN>
>>        bmAttributes = 0x0003  <INTERRUPT>
>>        wMaxPacketSize = 0x0008
>>        bInterval = 0x0028
>>        bRefresh = 0x0000
>>        bSynchAddress = 0x0000
>>
>>
> Hi,
>
> There is no RNDIS device here! There is only a UHID device.
>
> --HPS
>

I am not familiar with RNDIS..