huawei card

[Hug Me]

Tip has worked, I'm not sure why minicom did not. Here is the line I
had to set up in /etc/remote:

tmobile:dv=/dev/cuaU0.0:br#1700000:pa=none:

this was the result:
-----
hugme at dragoncon# tip tmobile
connected
ati
Manufacturer: huawei
Model: UMG181
Revision: 11.100.10.00.420
IMEI: 355768022267564
+GCAP: +CGSM,+FCLASS,+DS

OK
-----

PPP is the next step....



On Wed, Sep 2, 2009 at 7:31 AM, Hug Me<hugme at hugme.org> wrote:
> Well, I'm one step closer. I changed the line in /sys/dev/usb/usbdevs from this:
>
>  product HUAWEI MOBILE            0x1001  Huawei Mobile
>
> to this:
>
> product HUAWEI MOBILE              0x1414  Huawei Technology
>
> recompiled and the devices now show up... however, there are 4 of them:
>
> hugme at dragoncon# ls /dev/cuaU*
> /dev/cuaU0.0            /dev/cuaU0.1            /dev/cuaU0.2
>  /dev/cuaU0.3
> /dev/cuaU0.0.init       /dev/cuaU0.1.init       /dev/cuaU0.2.init
>  /dev/cuaU0.3.init
> /dev/cuaU0.0.lock       /dev/cuaU0.1.lock       /dev/cuaU0.2.lock
>  /dev/cuaU0.3.lock
>
> is this a default? I haven't been able to get them to initilize yet...
> tried minicom this morning, I'm going to configure remote to try tip
> in just a bit....
>
>
> On Tue, Sep 1, 2009 at 9:46 PM, Hug Me<hugme at hugme.org> wrote:
>> I've been having all sorts of trouble with this card. I've tried it
>> several ways. umass in the kernel, umass loaded manually, umass not
>> loaded at all... u3g in loaded manually or in the kernel, ubsa loaded
>> manually or in the kernel. I can't seem to get it detected as anything
>> except a storage device. I've tried the camcontrol eject and when it
>> comes back I still don't see the device....
>>
>> here is some of what I see:
>>
>> significant lines from boot with device in place
>> ...
>> umass0: <HUAWEI Technology HUAWEI Mobile, class 0/0, rev 2.00/0.00,
>> addr 2> on uhub0
>> umass1: <HUAWEI Technology HUAWEI Mobile, class 0/0, rev 2.00/0.00,
>> addr 2> on uhub0
>> ...
>> (probe2:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
>> (probe2:umass-sim0:0:0:0): CAM Status: SCSI Status Error
>> (probe2:umass-sim0:0:0:0): SCSI Status: Check Condition
>> (probe2:umass-sim0:0:0:0): NOT READY asc:3a,0
>> (probe2:umass-sim0:0:0:0): Medium not present
>> (probe2:umass-sim0:0:0:0): Unretryable error
>> (probe3:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
>> (probe3:umass-sim1:1:0:0): CAM Status: SCSI Status Error
>> (probe3:umass-sim1:1:0:0): SCSI Status: Check Condition
>> (probe3:umass-sim1:1:0:0): NOT READY asc:3a,0
>> (probe3:umass-sim1:1:0:0): Medium not present
>> (probe3:umass-sim1:1:0:0): Unretryable error
>> (probe0:mpt0:0:8:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
>> (probe0:mpt0:0:8:0): CAM Status: SCSI Status Error
>> (probe0:mpt0:0:8:0): SCSI Status: Check Condition
>> (probe0:mpt0:0:8:0): UNIT ATTENTION asc:29,0
>> (probe0:mpt0:0:8:0): Power on, reset, or bus device reset occurred
>> (probe0:mpt0:0:8:0): Retrying Command (per Sense Data)
>> ses0 at mpt0 bus 0 target 8 lun 0
>> ses0: <IBM 25P3495a S320  1 1> Fixed Processor SCSI-2 device
>> ses0: 3.300MB/s transfers
>> ses0: SAF-TE Compliant Device
>> da0 at mpt0 bus 0 target 0 lun 0
>> da0: <LSILOGIC 1030 IM 1000> Fixed Direct Access SCSI-2 device
>> da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
>> da0: Command Queueing Enabled
>> da0: 34702MB (71071561 512 byte sectors: 255H 63S/T 4424C)
>> SMP: AP CPU #2 Launched!
>> SMP: AP CPU #1 Launched!
>> SMP: AP CPU #3 Launched!
>> da1 at umass-sim1 bus 1 target 0 lun 0
>> da1: <HUAWEI MMC Storage 2.31> Removable Direct Access SCSI-2 device
>> da1: 1.000MB/s transfers
>> da1: Attempt to query device size failed: NOT READY, Medium not present
>> cd0 at umass-sim0 bus 0 target 0 lun 0
>> cd0: <HUAWEI Mass Storage 2.31> Removable CD-ROM SCSI-2 device
>> cd0: 1.000MB/s transfers
>> cd0: Attempt to query device size failed: NOT READY, Medium not present
>>
>>
>> with umass not loaded:
>> Unknown USB device: vendor 0x12d1 product 0x1414 bus uhub0
>> ugen0: <HUAWEI Technology HUAWEI Mobile, class 0/0, rev 2.00/0.00,
>> addr 2> on uhub0
>>
>> # usbdevs -v
>> Controller /dev/usb0:
>> addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
>> (0x1166)(0x0000), rev 1.00
>>  port 1 powered
>>  port 2 addr 2: full speed, self powered, config 1, HUAWEI
>> Mobile(0x1414), HUAWEI Technology(0x12d1), rev 0.00
>>  port 3 powered
>>  port 4 powered
>>
>>
>> Thanks for your help!
>>
>>
>> --
>>        *******************************************************************
>>        Don't ever forget to
>>                -*HUGME*-
>>
>> Yield to Temptation ... it may not pass your way again.
>>                -- Lazarus Long, "Time Enough for Love"
>>
>
>
>
> --
>        *******************************************************************
>        Don't ever forget to
>                -*HUGME*-
>
> Yield to Temptation ... it may not pass your way again.
>                -- Lazarus Long, "Time Enough for Love"
>



-- 
        *******************************************************************
        Don't ever forget to
                -*HUGME*-

Yield to Temptation ... it may not pass your way again.
                -- Lazarus Long, "Time Enough for Love"