controller errors from RELENG_9 to RELENG_10 upgrade
Mike Tancsa
mike at sentex.net
Thu Aug 28 18:38:19 UTC 2014
I upgraded one of our file servers to RELENG_10 this AM and noticed the
box started throwing a lot of errors all of a sudden on different disks
and port multipliers. The disks do not have any errors according to
smartctl. Now zfs detected write errors and forced a scrub on ada6
Any idea how to track this down ? dmesg and the errors attached in the
txt file.
loader is simple and is the same from before.
hint.siis.0.msi=1
siis.0.msi=1
hw.em.enable_msix=0
---Mike
--
-------------------
Mike Tancsa, tel +1 519 651 3400
Sentex Communications, mike at sentex.net
Providing Internet services since 1994 www.sentex.net
Cambridge, Ontario Canada http://www.tancsa.com/
-------------- next part --------------
Aug 28 10:20:26 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:20:26 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:20:26 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:20:26 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:20:27 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:20:27 backup3 kernel: siisch3: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:20:27 backup3 kernel: siisch3: ... waiting for slots 20000000
Aug 28 10:20:27 backup3 kernel: (ada6:siisch3:0:1:0): WRITE_FPDMA_QUEUED. ACB: 61 56 47 ba 00 40 a6 00 00 00 00 00
Aug 28 10:20:27 backup3 kernel: (ada6:siisch3:0:1:0): CAM status: ATA Status Error
Aug 28 10:20:27 backup3 kernel: (ada6:siisch3:0:1:0): ATA status: 00 ()
Aug 28 10:20:27 backup3 kernel: (ada6:siisch3:0:1:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:20:27 backup3 kernel: (ada6:siisch3:0:1:0): Retrying command
Aug 28 10:20:57 backup3 kernel: siisch3: Timeout on slot 29
Aug 28 10:20:57 backup3 kernel: siisch3: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:20:57 backup3 kernel: siisch3: ... waiting for slots 40000000
Aug 28 10:20:58 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:20:58 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:21:00 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:21:00 backup3 kernel: siisch1: siis_timeout is 00060002 ss f8000000 rs 48000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:21:00 backup3 kernel: siisch1: ... waiting for slots 08000000
Aug 28 10:22:31 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:22:31 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:22:31 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:22:31 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:22:31 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:22:31 backup3 kernel: siisch3: siis_timeout is 00000000 ss 40000000 rs 40000000 es 00000000 sts 801f2000 serr 00000000
Aug 28 10:23:02 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:23:02 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:23:02 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:23:02 backup3 kernel: siisch0: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:23:04 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:23:04 backup3 kernel: siisch0: siis_timeout is 00060002 ss f8000000 rs 48000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:23:04 backup3 kernel: siisch0: ... waiting for slots 08000000
Aug 28 10:23:34 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:23:34 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:23:34 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:23:34 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:23:34 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:23:34 backup3 kernel: siisch1: siis_timeout is 00000000 ss 40000000 rs 40000000 es 00000000 sts 801f2000 serr 00000000
Aug 28 10:24:05 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:24:05 backup3 kernel: siisch0: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:24:06 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:24:06 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:24:07 backup3 kernel: siisch0: Timeout on slot 26
Aug 28 10:24:07 backup3 kernel: siisch0: siis_timeout is 00060002 ss fe000000 rs 56000000 es 00000001 sts 001a2000 serr 00000000
Aug 28 10:24:07 backup3 kernel: siisch0: ... waiting for slots 52000000
Aug 28 10:24:37 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:24:37 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:24:37 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:24:37 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:25:09 backup3 kernel: siisch1: Timeout on slot 29
Aug 28 10:25:09 backup3 kernel: siisch1: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:25:09 backup3 kernel: siisch1: ... waiting for slots 40000000
Aug 28 10:25:09 backup3 kernel: siisch1: Timeout on slot 29
Aug 28 10:25:09 backup3 kernel: siisch1: siis_timeout is 00060002 ss e0000000 rs 20000000 es 00000001 sts 001d2000 serr 00000000
Aug 28 10:25:41 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:25:41 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:25:41 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:25:41 backup3 kernel: siisch0: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:12 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:26:12 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:13 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:26:13 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:44 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:26:44 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:44 backup3 kernel: siisch0: Timeout on slot 29
Aug 28 10:26:44 backup3 kernel: siisch0: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:44 backup3 kernel: siisch0: ... waiting for slots 40000000
Aug 28 10:26:44 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:26:44 backup3 kernel: siisch0: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:45 backup3 kernel: siisch1: Timeout on slot 29
Aug 28 10:26:45 backup3 kernel: siisch1: siis_timeout is 00060002 ss e0000000 rs 60000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:26:45 backup3 kernel: siisch1: ... waiting for slots 40000000
Aug 28 10:27:15 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:27:15 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:27:17 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:27:17 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:27:47 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:27:47 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:27:47 backup3 kernel: siisch0: Timeout on slot 29
Aug 28 10:27:47 backup3 kernel: siisch0: siis_timeout is 00060002 ss e0000000 rs 20000000 es 00000001 sts 001d2000 serr 00000000
Aug 28 10:27:48 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:27:48 backup3 kernel: siisch1: siis_timeout is 00060002 ss fc000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): READ_FPDMA_QUEUED. ACB: 60 10 10 86 e0 40 e8 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): CAM status: ATA Status Error
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): ATA status: 00 ()
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): Retrying command
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): READ_FPDMA_QUEUED. ACB: 60 10 10 84 e0 40 e8 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): CAM status: ATA Status Error
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): ATA status: 00 ()
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): Retrying command
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): READ_FPDMA_QUEUED. ACB: 60 10 10 02 00 40 00 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): CAM status: ATA Status Error
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): ATA status: 00 ()
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:48 backup3 kernel: (ada1:siisch1:0:1:0): Retrying command
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): READ_FPDMA_QUEUED. ACB: 60 10 10 86 e0 40 e8 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): CAM status: ATA Status Error
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): ATA status: 00 ()
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): Retrying command
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): READ_FPDMA_QUEUED. ACB: 60 10 10 84 e0 40 e8 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): CAM status: ATA Status Error
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): ATA status: 00 ()
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): Retrying command
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): WRITE_FPDMA_QUEUED. ACB: 61 01 4c fe 02 40 b4 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): CAM status: ATA Status Error
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): ATA status: 00 ()
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): Retrying command
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): READ_FPDMA_QUEUED. ACB: 60 10 10 02 00 40 00 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): CAM status: ATA Status Error
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): ATA status: 00 ()
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): RES: 00 00 00 00 00 00 00 00 00 00 00
Aug 28 10:27:49 backup3 kernel: (ada15:siisch0:0:2:0): Retrying command
Aug 28 10:28:50 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:28:50 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:28:50 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:28:50 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:28:51 backup3 kernel: siisch0: Timeout on slot 30
Aug 28 10:28:51 backup3 kernel: siisch0: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:28:51 backup3 kernel: siisch3: Timeout on slot 29
Aug 28 10:28:51 backup3 kernel: siisch3: siis_timeout is 00060002 ss fa000000 rs 32000000 es 00000001 sts 001d2000 serr 00000000
Aug 28 10:28:51 backup3 kernel: siisch3: ... waiting for slots 12000000
Aug 28 10:28:51 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:28:51 backup3 kernel: siisch1: siis_timeout is 00070003 ss d0000000 rs 78000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:28:51 backup3 kernel: siisch1: ... waiting for slots 38000000
Aug 28 10:29:21 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:29:21 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:29:21 backup3 kernel: siisch1: Timeout on slot 30
Aug 28 10:29:21 backup3 kernel: siisch1: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
Aug 28 10:29:52 backup3 kernel: siisch3: Timeout on slot 30
Aug 28 10:29:52 backup3 kernel: siisch3: siis_timeout is 00060002 ss c0000000 rs 40000000 es 00000001 sts 001e2000 serr 00000000
# camcontrol devlist
<WDC WD2001FASS-00U0B0 01.00101> at scbus0 target 0 lun 0 (pass20,ada13)
<WDC WD2001FASS-00U0B0 01.00101> at scbus0 target 1 lun 0 (pass19,ada12)
<WDC WD2001FASS-00U0B0 01.00101> at scbus0 target 2 lun 0 (pass21,ada14)
<WDC WD2001FASS-00U0B0 01.00101> at scbus0 target 3 lun 0 (pass22,ada15)
<Port Multiplier 47261095 1f06> at scbus0 target 15 lun 0 (pmp2,pass18)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus1 target 0 lun 0 (ada0,pass0)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus1 target 1 lun 0 (ada1,pass1)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus1 target 2 lun 0 (ada2,pass2)
<WDC WD2002FAEX-00MJRA0 01.01L01> at scbus1 target 3 lun 0 (ada3,pass3)
<Port Multiplier 38261095 1706> at scbus1 target 15 lun 0 (pass4,pmp0)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus3 target 0 lun 0 (ada4,pass5)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus3 target 1 lun 0 (ada5,pass6)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus3 target 3 lun 0 (ada6,pass7)
<WDC WD2002FAEX-007BA0 05.01D05> at scbus3 target 4 lun 0 (ada7,pass8)
<Port Multiplier 37261095 1706> at scbus3 target 15 lun 0 (pass9,pmp1)
<Areca usrvar R001> at scbus4 target 0 lun 0 (pass10,da0)
<Areca backup1 R001> at scbus4 target 0 lun 1 (pass11,da1)
<Areca RAID controller R001> at scbus4 target 16 lun 0 (pass12)
<AMCC 9650SE-2LP DISK 4.10> at scbus5 target 0 lun 0 (pass13,da2)
<WDC WD1002FAEX-00Y9A0 05.01D05> at scbus6 target 0 lun 0 (ada8,pass14)
<WDC WD1002FAEX-00Y9A0 05.01D05> at scbus7 target 0 lun 0 (ada9,pass15)
<ST31000340AS SD1A> at scbus8 target 0 lun 0 (ada10,pass16)
<WDC WD1002FAEX-00Z3A0 05.01D05> at scbus11 target 0 lun 0 (ada11,pass17)
# smartctl -a /dev/ada15
smartctl 6.3 2014-07-26 r3976 [FreeBSD 10.1-PRERELEASE amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD2001FASS-00U0B0
Serial Number: WD-WMAUR0387259
LU WWN Device Id: 5 0014ee 6aab7b9ff
Firmware Version: 01.00101
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Aug 28 11:06:51 2014 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (30900) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 353) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 073 040 021 Pre-fail Always - 13375
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 17
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 053 053 000 Old_age Always - 34868
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 13
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 11
193 Load_Cycle_Count 0x0032 134 134 000 Old_age Always - 200141
194 Temperature_Celsius 0x0022 111 105 000 Old_age Always - 41
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
# zpool status
pool: zbackup1
state: ONLINE
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are unaffected.
action: Determine if the device needs to be replaced, and clear the errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: http://illumos.org/msg/ZFS-8000-9P
scan: scrub in progress since Thu Aug 28 10:45:05 2014
470G scanned out of 21.5T at 209M/s, 29h23m to go
0 repaired, 2.13% done
config:
NAME STATE READ WRITE CKSUM
zbackup1 ONLINE 0 0 0
raidz1-0 ONLINE 0 0 0
diskid/DISK-WD-WCAW32276692 ONLINE 0 0 0
diskid/DISK-WD-WCATR4427343 ONLINE 0 0 0
diskid/DISK-WD-WCAW34265973 ONLINE 0 0 0
diskid/DISK-9QJ2TS3S ONLINE 0 0 0
raidz1-1 ONLINE 0 0 0
diskid/DISK-WD-WMAUR0331605 ONLINE 0 0 0
diskid/DISK-WD-WMAUR0378509 ONLINE 0 0 0
diskid/DISK-WD-WMAUR0327696 ONLINE 0 0 0
diskid/DISK-WD-WMAUR0387259 ONLINE 0 0 0
raidz1-2 ONLINE 0 0 0
ada3 ONLINE 0 0 0
ada0 ONLINE 0 0 0
ada2 ONLINE 0 0 0
ada1 ONLINE 0 0 0
raidz1-3 ONLINE 0 1 0
diskid/DISK-WD-WMAWP0079293 ONLINE 0 0 0
diskid/DISK-WD-WMAY03510311 ONLINE 0 0 0
diskid/DISK-WD-WMAWP0126093 ONLINE 0 1 0
diskid/DISK-WD-WMAWP0203774 ONLINE 3 125 0
# smartctl -x /dev/ada6
smartctl 6.3 2014-07-26 r3976 [FreeBSD 10.1-PRERELEASE amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Black
Device Model: WDC WD2002FAEX-007BA0
Serial Number: WD-WMAWP0203774
LU WWN Device Id: 5 0014ee 3aab9dd74
Firmware Version: 05.01D05
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Aug 28 11:24:39 2014 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (31860) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 308) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 240
3 Spin_Up_Time POS--K 253 253 021 - 6716
4 Start_Stop_Count -O--CK 100 100 000 - 22
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 000 - 0
9 Power_On_Hours -O--CK 074 074 000 - 19049
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 20
192 Power-Off_Retract_Count -O--CK 200 200 000 - 18
193 Load_Cycle_Count -O--CK 200 200 000 - 3
194 Temperature_Celsius -O---K 112 087 000 - 40
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1498
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb5 GPL,SL VS 1 Device vendor specific log
0xb6 GPL VS 1 Device vendor specific log
0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 40 Celsius
Power Cycle Min/Max Temperature: 39/41 Celsius
Lifetime Min/Max Temperature: 0/64 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (174)
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 2985 Vendor specific
Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-PRERELEASE #4 r270747: Thu Aug 28 08:54:45 EDT 2014
mdtancsa at backup3.sentex.ca:/crossbuilds/obj/10/crossbuilds/src/10/sys/GENERIC amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Core(TM) i5 CPU 660 @ 3.33GHz (3333.36-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x20652 Family = 0x6 Model = 0x25 Stepping = 2
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x298e3ff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,AESNI>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
VT-x: (disabled in BIOS) PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 12884901888 (12288 MB)
avail memory = 12373966848 (11800 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <INTEL S3420GPX>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 SMT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 4
cpu3 (AP): APIC ID: 5
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
kbd1 at kbdmux0
random: <Software, Yarrow> initialized
acpi0: <INTEL S3420GPX> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71,0x74-0x77 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 2.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> at device 3.0 on pci2
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 0.0 on pci4
pci5: <ACPI PCI bus> on pcib5
siis0: <SiI3124 SATA controller> port 0x3000-0x300f mem 0xb4408000-0xb440807f,0xb4400000-0xb4407fff irq 19 at device 0.0 on pci5
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
siisch2: <SIIS channel> at channel 2 on siis0
siisch3: <SIIS channel> at channel 3 on siis0
pcib6: <ACPI PCI-PCI bridge> at device 4.0 on pci2
pci6: <ACPI PCI bus> on pcib6
bge0: <HPQ 10/100/1000 Copper Based Gigabit Adapter, ASIC rev. 0x004001> mem 0xb4300000-0xb430ffff irq 16 at device 0.0 on pci6
bge0: CHIP ID 0x00004001; ASIC REV 0x04; CHIP REV 0x40; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:10:18:14:27:d5
pcib7: <ACPI PCI-PCI bridge> irq 16 at device 6.0 on pci0
pci7: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> at device 0.0 on pci7
pci8: <ACPI PCI bus> on pcib8
arcmsr0: <Areca SATA 3G Host Adapter RAID Controller
arcmsr version 1.20.00.28 2013-09-13
> mem 0xb4200000-0xb4200fff,0xb3c00000-0xb3ffffff irq 18 at device 14.0 on pci8
Areca RAID adapter0: ARC-1210 F/W version V1.49 2010-12-02
pcib9: <ACPI PCI-PCI bridge> at device 0.2 on pci7
pci9: <ACPI PCI bus> on pcib9
em0: <Intel(R) PRO/1000 Network Connection 7.4.2> port 0x4040-0x405f mem 0xb4500000-0xb451ffff,0xb4525000-0xb4525fff irq 16 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: Ethernet address: 00:15:17:ed:68:a5
ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xb4522000-0xb45223ff irq 21 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
pcib10: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci10: <ACPI PCI bus> on pcib10
pcib11: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci11: <ACPI PCI bus> on pcib11
em1: <Intel(R) PRO/1000 Network Connection 7.4.2> port 0x2000-0x201f mem 0xb4100000-0xb411ffff,0xb4120000-0xb4123fff irq 16 at device 0.0 on pci11
em1: Using an MSI interrupt
em1: Ethernet address: 00:15:17:ed:68:a4
pcib12: <ACPI PCI-PCI bridge> irq 18 at device 28.6 on pci0
pci12: <ACPI PCI bus> on pcib12
vgapci0: <VGA-compatible display> mem 0xb2000000-0xb2ffffff,0xb3800000-0xb3803fff,0xb3000000-0xb37fffff irq 17 at device 0.0 on pci12
vgapci0: Boot video device
pcib13: <ACPI PCI-PCI bridge> irq 19 at device 28.7 on pci0
pci13: <ACPI PCI bus> on pcib13
3ware device driver for 9000 series storage controllers, version: 3.80.06.003
twa0: <3ware 9000 series Storage Controller> port 0x1000-0x10ff mem 0xb0000000-0xb1ffffff,0xb4000000-0xb4000fff irq 19 at device 0.0 on pci13
twa0: INFO: (0x15: 0x1300): Controller details:: Model 9650SE-2LP, 2 ports, Firmware FE9X 4.10.00.021, BIOS BE9X 4.08.00.003
ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xb4521000-0xb45213ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci1
pcib14: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci14: <ACPI PCI bus> on pcib14
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel 5 Series/3400 Series AHCI SATA controller> port 0x4068-0x406f,0x4074-0x4077,0x4060-0x4067,0x4070-0x4073,0x4020-0x403f mem 0xb4520000-0xb45207ff irq 18 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 3Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
acpi_button0: <Sleep Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: console (115200,n,8,1)
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xcb000-0xcffff,0xd0000-0xd1fff,0xd3800-0xd57ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
(noperiph:siisch1:0:-1:ffffffff): rescan already queued
(noperiph:siisch3:0:-1:ffffffff): rescan already queued
Timecounters tick every 1.000 msec
random: unblocking device.
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
pmp0 at siisch1 bus 0 scbus1 target 15 lun 0
pmp0: <Port Multiplier 38261095 1706> ATA-0 device
pmp0: 300.000MB/s transfers (SATA 2.x, NONE, PIO 8192bytes)
pmp1 at siisch3 bus 0 scbus3 target 15 lun 0
pmp1: <Port Multiplier 37261095 1706> ATA-0 device
pmp1: 300.000MB/s transfers (SATA 2.x, NONE, PIO 8192bytes)
pmp0: 5 fan-out ports
pmp1: 5 fan-out ports
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on usbus1
da0 at arcmsr0 bus 0 scbus4 target 0 lun 0
da0: <Areca usrvar R001> Fixed Direct Access SCSI-5 device
da0: Serial Number 0000002992326304
da0: 250.000MB/s transfers (125.000MHz DT, offset 32, 16bit)
da0: Command Queueing enabled
da0: 76293MB (156249600 512 byte sectors: 255H 63S/T 9726C)
da1 at arcmsr0 bus 0 scbus4 target 0 lun 1
da1: <Areca backup1 R001> Fixed Direct Access SCSI-5 device
da1: Serial Number 0000002680492023
da1: 250.000MB/s transfers (125.000MHz DT, offset 32, 16bit)
da1: Command Queueing enabled
da1: 2784728MB (5703123456 512 byte sectors: 255H 63S/T 355003C)
da2 at twa0 bus 0 scbus5 target 0 lun 0
da2: <AMCC 9650SE-2LP DISK 4.10> Fixed Direct Access SCSI-5 device
da2: Serial Number S105182015D48400C2B2
da2: 100.000MB/s transfers
da2: 66747MB (136697856 512 byte sectors: 255H 63S/T 8509C)
ada0 at siisch1 bus 0 scbus1 target 0 lun 0
ada0: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 2.x device
ada0: Serial Number WD-WMAY03513634
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad6
ada1 at siisch1 bus 0 scbus1 target 1 lun 0
ada1: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 2.x device
ada1: Serial Number WD-WMAY03455725
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad7
ada2 at siisch1 bus 0 scbus1 target 2 lun 0
ada2: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 2.x device
ada2: Serial Number WD-WMAY02759120
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada3 at siisch1 bus 0 scbus1 target 3 lun 0
ada3: <WDC WD2002FAEX-00MJRA0 01.01L01> ATA-8 SATA 3.x device
ada3: Serial Number WD-WCC1P1023355
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada4 at siisch3 bus 0 scbus3 target 0 lun 0
ada4: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 3.x device
ada4: Serial Number WD-WMAWP0079293
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada4: Previously was known as ad10
ada5 at siisch3 bus 0 scbus3 target 1 lun 0
ada5: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 3.x device
ada5: Serial Number WD-WMAY03510311
ada5: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada5: Command Queueing enabled
ada5: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada5: Previously was known as ad11
ada6 at siisch3 bus 0 scbus3 target 3 lun 0
ada6: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 3.x device
ada6: Serial Number WD-WMAWP0203774
ada6: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada6: Command Queueing enabled
ada6: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada7 at siisch3 bus 0 scbus3 target 4 lun 0
ada7: <WDC WD2002FAEX-007BA0 05.01D05> ATA-8 SATA 3.x device
ada7: Serial Number WD-WMAWP0126093
ada7: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada7: Command Queueing enabled
ada7: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada8 at ahcich0 bus 0 scbus6 target 0 lun 0
ada8: <WDC WD1002FAEX-00Y9A0 05.01D05> ATA-8 SATA 3.x device
ada8: Serial Number WD-WCAW34265973
ada8: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada8: Command Queueing enabled
ada8: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada8: Previously was known as ad12
ada9 at ahcich1 bus 0 scbus7 target 0 lun 0
ada9: <WDC WD1002FAEX-00Y9A0 05.01D05> ATA-8 SATA 3.x device
ada9: Serial Number WD-WCAW32276692
ada9: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada9: Command Queueing enabled
ada9: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada9: Previously was known as ad14
ada10 at ahcich2 bus 0 scbus8 target 0 lun 0
ada10: <ST31000340AS SD1A> ATA-8 SATA 2.x device
ada10: Serial Number 9QJ2TS3S
ada10: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada10: Command Queueing enabled
ada10: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada10: Previously was known as ad16
ada11 at ahcich5 bus 0 scbus11 target 0 lun 0
ada11: <WDC WD1002FAEX-00Z3A0 05.01D05> ATA-8 SATA 3.x device
ada11: Serial Number WD-WCATR4427343
ada11: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada11: Command Queueing enabled
ada11: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
ada11: Previously was known as ad22
pass12 at arcmsr0 bus 0 scbus4 target 16 lun 0
pass12: <Areca RAID controller R001> Fixed Processor SCSI-0 device
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
lapic5: Forcing LINT1 to edge trigger
SMP: AP CPU #3 Launched!
lapic4: Forcing LINT1 to edge trigger
SMP: AP CPU #2 Launched!
Timecounter "TSC-low" frequency 1666680262 Hz quality 1000
uhub2: 6 ports with 6 removable, self powered
uhub3: 6 ports with 6 removable, self powered
ugen1.3: <American Megatrends Inc.> at usbus1
ukbd0: <Keyboard Interface> on usbus1
kbd0 at ukbd0
ugen0.3: <American Power Conversion> at usbus0
Root mount waiting for: usbus1 usbus0
ugen1.4: <USB> at usbus1
ukbd2: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 4> on usbus1
kbd2 at ukbd2
ugen0.4: <American Power Conversion> at usbus0
Root mount waiting for: usbus0
Trying to mount root from ufs:/dev/da2s1a [rw]...
pmp2 at siisch0 bus 0 scbus0 target 15 lun 0
pmp2: <Port Multiplier 47261095 1f06> ATA-0 device
pmp2: 300.000MB/s transfers (SATA 2.x, NONE, PIO 8192bytes)
pmp2: 5 fan-out ports
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
ada12 at siisch0 bus 0 scbus0 target 1 lun 0
ada12: <WDC WD2001FASS-00U0B0 01.00101> ATA-8 SATA 2.x device
ada12: Serial Number WD-WMAUR0378509
ada12: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada12: Command Queueing enabled
ada12: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada12: Previously was known as ad5
ada13 at siisch0 bus 0 scbus0 target 0 lun 0
ada13: <WDC WD2001FASS-00U0B0 01.00101> ATA-8 SATA 2.x device
ada13: Serial Number WD-WMAUR0331605
ada13: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada13: Command Queueing enabled
ada13: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada13: Previously was known as ad4
ada14 at siisch0 bus 0 scbus0 target 2 lun 0
ada14: <WDC WD2001FASS-00U0B0 01.00101> ATA-8 SATA 2.x device
ada14: Serial Number WD-WMAUR0327696
ada14: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada14: Command Queueing enabled
ada14: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada15 at siisch0 bus 0 scbus0 target 3 lun 0
ada15: <WDC WD2001FASS-00U0B0 01.00101> ATA-8 SATA 2.x device
ada15: Serial Number WD-WMAUR0387259
ada15: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada15: Command Queueing enabled
ada15: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ums0: <Mouse Interface> on usbus1
ums0: 3 buttons and [Z] coordinates ID=0
uhid0: <USB USB Keykoard, class 0/0, rev 1.10/1.10, addr 4> on usbus1
em0: link state changed to UP
em1: link state changed to UP
# pciconf -lvcb siis0
siis0 at pci0:5:0:0: class=0x010400 card=0x71241095 chip=0x31241095 rev=0x02 hdr=0x00
vendor = 'Silicon Image, Inc.'
device = 'SiI 3124 PCI-X Serial ATA Controller'
class = mass storage
subclass = RAID
bar [10] = type Memory, range 64, base 0xb4408000, size 128, enabled
bar [18] = type Memory, range 64, base 0xb4400000, size 32768, enabled
bar [20] = type I/O Port, range 32, base 0x3000, size 16, enabled
cap 01[64] = powerspec 2 supports D0 D1 D2 D3 current D0
cap 07[40] = PCI-X 64-bit supports 133MHz, 2048 burst read, 12 split transactions
cap 05[54] = MSI supports 1 message, 64 bit enabled with 1 message
More information about the freebsd-stable
mailing list