Network unavailable when booting directly to FreeBSD.

[Pedro Giffuni]

Hello;

--- Sab 23/6/12, YongHyeon PYUN <pyunyh at gmail.com> ha scritto:
...
> 
> > amd64
> > 
> > From my dmesg
> > ______
> > ...
> > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on
> acpi0
> > pcib0: Length mismatch for 4 range: 81 vs 7f
> > pci0: <ACPI PCI bus> on pcib0
> > pci0: <memory, RAM> at device 0.0 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.1 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.2 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.3 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.4 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.5 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.6 (no driver
> attached)
> > pci0: <memory, RAM> at device 0.7 (no driver
> attached)
> > pcib1: <ACPI PCI-PCI bridge> at device 2.0 on
> pci0
> > pci1: <ACPI PCI bus> on pcib1
> > pcib2: <ACPI PCI-PCI bridge> at device 3.0 on
> pci0
> > pci2: <ACPI PCI bus> on pcib2
> > bge0: <Broadcom NetXtreme Gigabit Ethernet
> Controller, ASIC rev. 
> > 0x00b002> mem 0xfdef0000-0xfdefffff irq 16 at device
> 0.0 on pci2
> > bge0: CHIP ID 0x0000b002; ASIC REV 0x0b; CHIP REV 0xb0;
> PCI-E
> > miibus0: <MII bus> on bge0
> > brgphy0: <BCM5754/5787 1000BASE-T media
> interface> PHY 1 on miibus0
> > brgphy0:  10baseT, 10baseT-FDX, 100baseTX,
> 100baseTX-FDX, 1000baseT, 
> > 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master,
> auto, auto-flow
> > bge0: Ethernet address: 00:18:8b:76:a4:1e
> > pcib3: <ACPI PCI-PCI bridge> at device 4.0 on
> pci0
> > pci3: <ACPI PCI bus> on pcib3
> > 
> > ....
> > Cuse4BSD v0.1.23 @ /dev/cuse
> > bge0: watchdog timeout -- resetting
> > bge0: watchdog timeout -- resetting
> > WARNING: attempt to domain_add(bluetooth) after
> domainfinalize()
> > fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8
> > bge0: watchdog timeout -- resetting
> > bge0: link state changed to DOWN
> > bge0: link state changed to UP
> > bge0: watchdog timeout -- resetting
> > bge0: link state changed to DOWN
> > bge0: link state changed to UP
> > bge0: watchdog timeout -- resetting
> > bge0: link state changed to DOWN
> > bge0: link state changed to UP
> > _____
> > 
> > Iff I boot Windows first and then reboot to start
> > FreeBSD the network works fine.
> 
> This looks strange and I can't narrow down what other
> changes made
> since 9.0-RELEASE broke the driver. Would you try reverting
> r235821?
> 

I reverted it manually but things didn't change.

> If that does not solve the issue, would you try a WIP
> version at
> the following URL? It's mainly written to improve BCM5720
> with APE
> firmware support and it exactly follows recommendations
> suggested
> by Broadcom so it may have some differences.
> 
> http://people.freebsd.org/~yongari/bge/if_bge.c
> http://people.freebsd.org/~yongari/bge/if_bgereg.h
> http://people.freebsd.org/~yongari/bge/brgphy.c
> 

No joy either :(

Pedro.