FreeBSD 8.2 and Lenovo X300 WWAN Modem

[crsnet.pl]

 On Wed, 18 May 2011 12:05:20 +0200, Maciej Milewski <milu at dat.pl> 
 wrote:
> Dnia środa, 18 maja 2011 o 11:40:36 crsnet.pl napisał(a):
>>  Hello.
>>  Have here anyone run this modem/GPS under FreeBSD 8.2 ? Modem is
>>  recognized, but when i try to run ppp -ddial iplus i get this error 
>> :
>>
>>  /var/log/messages
>>  May 18 11:20:59 x60s ppp[1656]: tun0: Warning: Chat script failed
>>
>>  /var/log/ppp
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Phase: deflink: opening -> 
>> dial
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Send: AT^M
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Expect(2): OK
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Received: AT^M^M
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Received: OK^M
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Send: AT+CFUN=1^M
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Expect(2): OK
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Received: AT+CFUN=1^M^M
>>  May 18 11:20:53 x60s ppp[1656]: tun0: Chat: Received: ERROR^M
>>
>>
>>  For GPS i try to use
>>  gpsdrive-2.09_11    A GPS navigation system
>>  viking-1.0.2        Program to manage GPS data (tracks, waypoints, 
>> etc)
>>  But any of them can use X300 GPS;/
>>
>>  #uname -a
>>  FreeBSD x60s 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Fri Feb 18 
>> 02:24:46
>>  UTC 2011     
>> root at almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
>>  i386
>>
>>  #dmesg
>>  ugen6.3: <vendor 0x17ef> at usbus6
>>  ugen4.2: <Sierra Wireless, Incorporated> at usbus4
>>  u3g0: <Data Interface> on usbus4
>>  u3g0: Found 3 ports.
>>
>>  #sudo usbconfig
>>  ugen4.2: <Sierra Wireless MC5725 Modem Sierra Wireless, 
>> Incorporated>
>>  at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
>>  ugen6.4: <Wimedia device ManfID> at usbus6, cfg=0 md=HOST spd=HIGH
>>  (480Mbps) pwr=ON
>>
>>  #ls -la /dev/cuaU*
>>  crw-rw----  1 uucp  dialer    0, 123 18 maj 09:39 /dev/cuaU0.0
>>  crw-rw----  1 uucp  dialer    0, 124 18 maj 09:39 /dev/cuaU0.0.init
>>  crw-rw----  1 uucp  dialer    0, 125 18 maj 09:39 /dev/cuaU0.0.lock
>>  crw-rw----  1 uucp  dialer    0, 129 18 maj 09:39 /dev/cuaU0.1
>>  crw-rw----  1 uucp  dialer    0, 130 18 maj 09:39 /dev/cuaU0.1.init
>>  crw-rw----  1 uucp  dialer    0, 131 18 maj 09:39 /dev/cuaU0.1.lock
>>  crw-rw----  1 uucp  dialer    0, 135 18 maj 09:39 /dev/cuaU0.2
>>  crw-rw----  1 uucp  dialer    0, 136 18 maj 09:39 /dev/cuaU0.2.init
>>  crw-rw----  1 uucp  dialer    0, 137 18 maj 09:39 /dev/cuaU0.2.lock
>>
>>  #cat /etc/ppp/ppp.conf
>>  iplus:
>>   set log Phase Chat LCP IPCP CCP tun command
>>   ident user-ppp VERSION (built COMPILATIONDATE)
>>
>>   set device /dev/cuaU0.0
>>   set speed 460800
>>   #set speed 115200
>>   set dial "ABORT BUSY TIMEOUT 2 \
>>          \"\" \
>>          AT OK-AT-OK \
>>          AT+CFUN=1 OK-AT-OK \
>>          AT+CMEE=2 OK-AT-OK \
>>          AT+CSQ OK \
>>          AT+CGDCONT=1,\\\"IP\\\",\\\"internet\\\" OK \
>>          AT+CGACT? OK-AT-OK \
>>          AT+CGATT? OK \
>>          AT+CGCLASS? OK \
>>          AT+COPS? OK \
>>          ATD*99***1# CONNECT"
>>
>>   set timeout 180
>>   enable dns
>>   set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
>>   add default HISADDR
>>
>>  Regards, Adrian.
> Do you have a pin defined on sim?
 No.
 I check with minicom that AT+CFUN=1 (Turns modem on) give Error but 
 AT+PCSTATE=1 turns it on.
 Unfortunately when i change it in ppp.conf from AT+CFUN=1 to 
 AT+PCSTATE=1 that give me
 May 18 12:13:48 x60s ppp[2697]: tun0: Chat: Send: AT+PCSTATE=1^M
 May 18 12:13:48 x60s ppp[2697]: tun0: Chat: Expect(2): OK
 May 18 12:13:48 x60s ppp[2697]: tun0: Chat: Received: AT+PCSTATE=1^M^M
 May 18 12:13:48 x60s ppp[2697]: tun0: Chat: Received: ERROR^M
 May 18 12:13:50 x60s ppp[2697]: tun0: Chat: Expect timeout

>
> --
> Maciej