scp: Write Failed: Cannot allocate memory
Scott Sipe
cscotts at gmail.com
Wed Jul 6 04:34:16 UTC 2011
On Jul 6, 2011, at 12:15 AM, Jeremy Chadwick wrote:
> On Wed, Jul 06, 2011 at 01:54:12PM +1000, Peter Ross wrote:
>> Quoting "Jeremy Chadwick" <freebsd at jdc.parodius.com>:
>>
>>> On Wed, Jul 06, 2011 at 01:07:53PM +1000, Peter Ross wrote:
>>>> Quoting "Jeremy Chadwick" <freebsd at jdc.parodius.com>:
>>>>
>>>>> On Wed, Jul 06, 2011 at 12:23:39PM +1000, Peter Ross wrote:
>>>>>> Quoting "Jeremy Chadwick" <freebsd at jdc.parodius.com>:
>>>>>>
>>>>>>> On Tue, Jul 05, 2011 at 01:03:20PM -0400, Scott Sipe wrote:
>>>>>>>> I'm running virtualbox 3.2.12_1 if that has anything to do with it.
>>>>>>>>
>>>>>>>> sysctl vfs.zfs.arc_max: 6200000000
>>>>>>>>
>>>>>>>> While I'm trying to scp, kstat.zfs.misc.arcstats.size is
>>>>>>>> hovering right around that value, sometimes above, sometimes
>>>>>>>> below (that's as it should be, right?). I don't think that it
>>>>>>>> dies when crossing over arc_max. I can run the same scp 10 times
>>>>>>>> and it might fail 1-3 times, with no correlation to the
>>>>>>>> arcstats.size being above/below arc_max that I can see.
>>>>>>>>
>>>>>>>> Scott
>>>>>>>>
>>>>>>>> On Jul 5, 2011, at 3:00 AM, Peter Ross wrote:
>>>>>>>>
>>>>>>>>> Hi all,
>>>>>>>>>
>>>>>>>>> just as an addition: an upgrade to last Friday's
>>>>>>>>> FreeBSD-Stable and to VirtualBox 4.0.8 does not fix the
>>>>>>>>> problem.
>>>>>>>>>
>>>>>>>>> I will experiment a bit more tomorrow after hours and grab
>>>>>> some statistics.
>>>>>>>>>
>>>>>>>>> Regards
>>>>>>>>> Peter
>>>>>>>>>
>>>>>>>>> Quoting "Peter Ross" <Peter.Ross at bogen.in-berlin.de>:
>>>>>>>>>
>>>>>>>>>> Hi all,
>>>>>>>>>>
>>>>>>>>>> I noticed a similar problem last week. It is also very
>>>>>>>>>> similar to one reported last year:
>>>>>>>>>>
>>>>>>>>>> http://lists.freebsd.org/pipermail/freebsd-stable/2010-September/058708.html
>>>>>>>>>>
>>>>>>>>>> My server is a Dell T410 server with the same bge card (the
>>>>>>>>>> same pciconf -lvc output as described by Mahlon:
>>>>>>>>>>
>>>>>>>>>> http://lists.freebsd.org/pipermail/freebsd-stable/2010-September/058711.html
>>>>>>>>>>
>>>>>>>>>> Yours, Scott, is a em(4)..
>>>>>>>>>>
>>>>>>>>>> Another similarity: In all cases we are using VirtualBox. I
>>>>>>>>>> just want to mention it, in case it matters. I am still
>>>>>>>>>> running VirtualBox 3.2.
>>>>>>>>>>
>>>>>>>>>> Most of the time kstat.zfs.misc.arcstats.size was reaching
>>>>>>>>>> vfs.zfs.arc_max then, but I could catch one or two cases
>>>>>>>>>> then the value was still below.
>>>>>>>>>>
>>>>>>>>>> I added vfs.zfs.prefetch_disable=1 to sysctl.conf but it
>>>> does not help.
>>>>>>>>>>
>>>>>>>>>> BTW: It looks as ARC only gives back the memory when I
>>>>>>>>>> destroy the ZFS (a cloned snapshot containing virtual
>>>>>>>>>> machines). Even if nothing happens for hours the buffer
>>>>>>>>>> isn't released..
>>>>>>>>>>
>>>>>>>>>> My machine was still running 8.2-PRERELEASE so I am upgrading.
>>>>>>>>>>
>>>>>>>>>> I am happy to give information gathered on old/new kernel if it helps.
>>>>>>>>>>
>>>>>>>>>> Regards
>>>>>>>>>> Peter
>>>>>>>>>>
>>>>>>>>>> Quoting "Scott Sipe" <cscotts at gmail.com>:
>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> On Jul 2, 2011, at 12:54 AM, jhell wrote:
>>>>>>>>>>>
>>>>>>>>>>>> On Fri, Jul 01, 2011 at 03:22:32PM -0700, Jeremy Chadwick wrote:
>>>>>>>>>>>>> On Fri, Jul 01, 2011 at 03:13:17PM -0400, Scott Sipe wrote:
>>>>>>>>>>>>>> I'm running 8.2-RELEASE and am having new problems
>>>>>>>>>>>>>> with scp. When scping
>>>>>>>>>>>>>> files to a ZFS directory on the FreeBSD server --
>>>>>>>>>>>>>> most notably large files
>>>>>>>>>>>>>> -- the transfer frequently dies after just a few
>>>>>>>>>>>>>> seconds. In my last test, I
>>>>>>>>>>>>>> tried to scp an 800mb file to the FreeBSD system and
>>>>>>>>>>>>>> the transfer died after
>>>>>>>>>>>>>> 200mb. It completely copied the next 4 times I
>>>>>>>>>>>>>> tried, and then died again on
>>>>>>>>>>>>>> the next attempt.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> On the client side:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> "Connection to home closed by remote host.
>>>>>>>>>>>>>> lost connection"
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> In /var/log/auth.log:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Jul 1 14:54:42 freebsd sshd[18955]: fatal: Write
>>>>>>>>>>>>>> failed: Cannot allocate
>>>>>>>>>>>>>> memory
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I've never seen this before and have used scp before
>>>>>>>>>>>>>> to transfer large files
>>>>>>>>>>>>>> without problems. This computer has been used in
>>>>>>>>>>>>>> production for months and
>>>>>>>>>>>>>> has a current uptime of 36 days. I have not been
>>>>>>>>>>>>>> able to notice any problems
>>>>>>>>>>>>>> copying files to the server via samba or netatalk, or
>>>>>> any problems in
>>>>>>>>>>>>>> apache.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Uname:
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> FreeBSD xeon 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Sat
>>>>>>>>>>>>>> Feb 19 01:02:54 EST
>>>>>>>>>>>>>> 2011 root at xeon:/usr/obj/usr/src/sys/GENERIC amd64
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I've attached my dmesg and output of vmstat -z.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I have not restarted the sshd daemon or rebooted the computer.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> Am glad to provide any other information or test anything else.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> {snip vmstat -z and dmesg}
>>>>>>>>>>>>>
>>>>>>>>>>>>> You didn't provide details about your networking setup (rc.conf,
>>>>>>>>>>>>> ifconfig -a, etc.). netstat -m would be useful too.
>>>>>>>>>>>>>
>>>>>>>>>>>>> Next, please see this thread circa September 2010, titled "Network
>>>>>>>>>>>>> memory allocation failures":
>>>>>>>>>>>>>
>>>>>>>>>>>>> http://lists.freebsd.org/pipermail/freebsd-stable/2010-September/thread.html#58708
>>>>>>>>>>>>>
>>>>>>>>>>>>> The user in that thread is using rsync, which relies on
>>>>>> scp by default.
>>>>>>>>>>>>> I believe this problem is similar, if not identical, to yours.
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> Please also provide your output of ( /usr/bin/limits -a )
>>>>>> for the server
>>>>>>>>>>>> end and the client.
>>>>>>>>>>>>
>>>>>>>>>>>> I am not quite sure I agree with the need for ifconfig -a but some
>>>>>>>>>>>> information about the networking driver your using for the interface
>>>>>>>>>>>> would be helpful, uptime of the boxes. And configuration
>>>> of the pool.
>>>>>>>>>>>> e.g. ( zpool status -a ;zfs get all <poolname> ) You should probably
>>>>>>>>>>>> prop this information up somewhere so you can reference by
>>>>>> URL whenever
>>>>>>>>>>>> needed.
>>>>>>>>>>>>
>>>>>>>>>>>> rsync(1) does not rely on scp(1) whatsoever but rsync(1)
>>>>>> can be made to
>>>>>>>>>>>> use ssh(1) instead of rsh(1) and I believe that is what Jeremy is
>>>>>>>>>>>> stating here but correct me if I am wrong. It does use ssh(1) by
>>>>>>>>>>>> default.
>>>>>>>>>>>>
>>>>>>>>>>>> Its a possiblity as well that if using tmpfs(5) or mdmfs(8) for /tmp
>>>>>>>>>>>> type filesystems that rsync(1) may be just filling up your
>>>>>> temp ram area
>>>>>>>>>>>> and causing the connection abort which would be
>>>>>>>>>>>> expected. ( df -h ) would
>>>>>>>>>>>> help here.
>>>>>>>>>>>
>>>>>>>>>>> Hello,
>>>>>>>>>>>
>>>>>>>>>>> I'm not using tmpfs/mdmfs at all. The clients yesterday
>>>>>>>>>>> were 3 different OSX computers (over gigabit). The FreeBSD
>>>>>>>>>>> server has 12gb of ram and no bce adapter. For what it's
>>>>>>>>>>> worth, the server is backed up remotely every night with
>>>>>>>>>>> rsync (remote FreeBSD uses rsync to pull) to an offsite
>>>>>>>>>>> (slow cable connection) FreeBSD computer, and I have not
>>>>>>>>>>> seen any errors in the nightly rsync.
>>>>>>>>>>>
>>>>>>>>>>> Sorry for the omission of networking info, here's the
>>>>>>>>>>> output of the requested commands and some that popped up
>>>>>>>>>>> in the other thread:
>>>>>>>>>>>
>>>>>>>>>>> http://www.cap-press.com/misc/
>>>>>>>>>>>
>>>>>>>>>>> In rc.conf: ifconfig_em1="inet 10.1.1.1 netmask 255.255.0.0"
>>>>>>>>>>>
>>>>>>>>>>> Scott
>>>>>>>
>>>>>>> Just to make it crystal clear to everyone:
>>>>>>>
>>>>>>> There is no correlation between this problem and use of ZFS. People are
>>>>>>> attempting to correlate "cannot allocate memory" messages with "anything
>>>>>>> on the system that uses memory". The VM is much more complex than that.
>>>>>>>
>>>>>>> Given the nature of this problem, it's much more likely the issue is
>>>>>>> "somewhere" within a networking layer within FreeBSD, whether it be
>>>>>>> driver-level or some sort of intermediary layer.
>>>>>>>
>>>>>>> Two people who have this issue in this thread are both using VirtualBox.
>>>>>>> Can one, or both, of you remove VirtualBox from the configuration
>>>>>>> entirely (kernel, etc. -- not sure what is required) and then see if the
>>>>>>> issue goes away?
>>>>>>
>>>>>> On the machine in question I only can do it after hours so I will do
>>>>>> it tonight.
>>>>>>
>>>>>> I was _successfully_ sending the file over the loopback interface using
>>>>>>
>>>>>> cat /zpool/temp/zimbra_oldroot.vdi | ssh localhost "cat > /dev/null"
>>>>>>
>>>>>> I did it, btw, with the IPv6 localhost address first (accidently),
>>>>>> and then using IPv4. Both worked.
>>>>>>
>>>>>> It always fails if I am sending it through the bce(4) interface,
>>>>>> even if my target is the VirtualBox bridged to the bce card (so it
>>>>>> does not "leave" the computer physically).
>>>>>>
>>>>>> Below the uname -a, ifconfig -a, netstat -rn, pciconf -lv and
>>>>>> kldstat output.
>>>>>>
>>>>>> I have another box where I do not see that problem. It copies files
>>>>>> happily over the net using ssh.
>>>>>>
>>>>>> It is an an older HP ML 150 with 3GB RAM only but with a bge(4)
>>>>>> driver instead. It runs the same last week's RELENG_8. I installed
>>>>>> VirtualBox and enabled vboxnet (so it loads the kernel modules). But
>>>>>> I do not run VirtualBox on it (because it hasn't enough RAM).
>>>>>>
>>>>>> Regards
>>>>>> Peter
>>>>>>
>>>>>> DellT410one# uname -a
>>>>>> FreeBSD DellT410one.vv.fda 8.2-STABLE FreeBSD 8.2-STABLE #1: Thu Jun
>>>>>> 30 17:07:18 EST 2011
>>>>>> root at DellT410one.vv.fda:/usr/obj/usr/src/sys/GENERIC amd64
>>>>>> DellT410one# ifconfig -a
>>>>>> bce0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST>
>>>>>> metric 0 mtu 1500
>>>>>> options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
>>>>>> ether 84:2b:2b:68:64:e4
>>>>>> inet 192.168.50.220 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.221 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.223 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.224 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.225 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.226 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.227 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> inet 192.168.50.219 netmask 0xffffff00 broadcast 192.168.50.255
>>>>>> media: Ethernet autoselect (1000baseT <full-duplex>)
>>>>>> status: active
>>>>>> bce1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
>>>>>> options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE>
>>>>>> ether 84:2b:2b:68:64:e5
>>>>>> media: Ethernet autoselect
>>>>>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>>>>>> options=3<RXCSUM,TXCSUM>
>>>>>> inet6 fe80::1%lo0 prefixlen 64 scopeid 0xb
>>>>>> inet6 ::1 prefixlen 128
>>>>>> inet 127.0.0.1 netmask 0xff000000
>>>>>> nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
>>>>>> vboxnet0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
>>>>>> ether 0a:00:27:00:00:00
>>>>>> DellT410one# netstat -rn
>>>>>> Routing tables
>>>>>>
>>>>>> Internet:
>>>>>> Destination Gateway Flags Refs Use Netif Expire
>>>>>> default 192.168.50.201 UGS 0 52195 bce0
>>>>>> 127.0.0.1 link#11 UH 0 6 lo0
>>>>>> 192.168.50.0/24 link#1 U 0 1118212 bce0
>>>>>> 192.168.50.219 link#1 UHS 0 9670 lo0
>>>>>> 192.168.50.220 link#1 UHS 0 8347 lo0
>>>>>> 192.168.50.221 link#1 UHS 0 103024 lo0
>>>>>> 192.168.50.223 link#1 UHS 0 43614 lo0
>>>>>> 192.168.50.224 link#1 UHS 0 8358 lo0
>>>>>> 192.168.50.225 link#1 UHS 0 8438 lo0
>>>>>> 192.168.50.226 link#1 UHS 0 8338 lo0
>>>>>> 192.168.50.227 link#1 UHS 0 8333 lo0
>>>>>> 192.168.165.0/24 192.168.50.200 UGS 0 3311 bce0
>>>>>> 192.168.166.0/24 192.168.50.200 UGS 0 699 bce0
>>>>>> 192.168.167.0/24 192.168.50.200 UGS 0 3012 bce0
>>>>>> 192.168.168.0/24 192.168.50.200 UGS 0 552 bce0
>>>>>>
>>>>>> Internet6:
>>>>>> Destination Gateway
>>>>>> Flags Netif Expire
>>>>>> ::1 ::1 UH
>>>>>> lo0
>>>>>> fe80::%lo0/64 link#11 U
>>>>>> lo0
>>>>>> fe80::1%lo0 link#11 UHS
>>>>>> lo0
>>>>>> ff01::%lo0/32 fe80::1%lo0 U
>>>>>> lo0
>>>>>> ff02::%lo0/32 fe80::1%lo0 U
>>>>>> lo0
>>>>>> DellT410one# kldstat
>>>>>> Id Refs Address Size Name
>>>>>> 1 19 0xffffffff80100000 dbf5d0 kernel
>>>>>> 2 3 0xffffffff80ec0000 4c358 vboxdrv.ko
>>>>>> 3 1 0xffffffff81012000 131998 zfs.ko
>>>>>> 4 1 0xffffffff81144000 1ff1 opensolaris.ko
>>>>>> 5 2 0xffffffff81146000 2940 vboxnetflt.ko
>>>>>> 6 2 0xffffffff81149000 8e38 netgraph.ko
>>>>>> 7 1 0xffffffff81152000 153c ng_ether.ko
>>>>>> 8 1 0xffffffff81154000 e70 vboxnetadp.ko
>>>>>> DellT410one# pciconf -lv
>>>>>> ..
>>>>>> bce0 at pci0:1:0:0: class=0x020000 card=0x028d1028
>>>>>> chip=0x163b14e4 rev=0x20 hdr=0x00
>>>>>> vendor = 'Broadcom Corporation'
>>>>>> class = network
>>>>>> subclass = ethernet
>>>>>> bce1 at pci0:1:0:1: class=0x020000 card=0x028d1028
>>>>>> chip=0x163b14e4 rev=0x20 hdr=0x00
>>>>>> vendor = 'Broadcom Corporation'
>>>>>> class = network
>>>>>> subclass = ethernet
>>>>>
>>>>> Could you please provide "pciconf -lvcb" output instead, specific to the
>>>>> bce chips? Thanks.
>>>>
>>>> Her it is:
>>>>
>>>> bce0 at pci0:1:0:0: class=0x020000 card=0x028d1028
>>>> chip=0x163b14e4 rev=0x20 hdr=0x00
>>>> vendor = 'Broadcom Corporation'
>>>> class = network
>>>> subclass = ethernet
>>>> bar [10] = type Memory, range 64, base 0xda000000, size
>>>> 33554432, enabled
>>>> cap 01[48] = powerspec 3 supports D0 D3 current D0
>>>> cap 03[50] = VPD
>>>> cap 05[58] = MSI supports 16 messages, 64 bit enabled with 1 message
>>>> cap 11[a0] = MSI-X supports 9 messages in map 0x10
>>>> cap 10[ac] = PCI-Express 2 endpoint max data 256(512) link x4(x4)
>>>> ecap 0003[100] = Serial 1 842b2bfffe6864e4
>>>> ecap 0001[110] = AER 1 0 fatal 0 non-fatal 1 corrected
>>>> ecap 0004[150] = unknown 1
>>>> ecap 0002[160] = VC 1 max VC0
>>>
>>> Thanks Peter.
>>>
>>> Adding Yong-Hyeon and David to the discussion, since they've both worked
>>> on the bce(4) driver in recent months (most of the changes made recently
>>> are only in HEAD), and also adding Jack Vogel of Intel who maintains
>>> em(4). Brief history for the devs:
>>>
>>> The issue is described "Network memory allocation failures" and was
>>> reported last year, but two users recently (Scott and Peter) have
>>> reported the issue again:
>>>
>>> http://lists.freebsd.org/pipermail/freebsd-stable/2010-September/thread.html#58708
>>>
>>> And was mentioned again by Scott here, which also contains some
>>> technical details:
>>>
>>> http://lists.freebsd.org/pipermail/freebsd-stable/2011-July/063172.html
>>>
>>> What's interesting is that Scott's issue is identical in form but he's
>>> using em(4), which isn't known to behave like this. Both individuals
>>> are using VirtualBox, though we're not sure at this point if that is the
>>> piece which is causing the anomaly.
>>>
>>> Relevant details of Scott's system (em-based):
>>>
>>> http://www.cap-press.com/misc/
>>>
>>> Relevant details of Peter's system (bce-based):
>>>
>>> http://lists.freebsd.org/pipermail/freebsd-stable/2011-July/063221.html
>>> http://lists.freebsd.org/pipermail/freebsd-stable/2011-July/063223.html
>>>
>>> I think the biggest complexity right now is figuring out how/why scp
>>> fails intermittently in this nature. The errno probably "trickles down"
>>> to userland from the kernel, but the condition regarding why it happens
>>> is unknown.
>>
>> BTW: I also saw 2 of the errors coming from a BIND9 running in a
>> jail on that box.
>>
>> DellT410one# fgrep -i allocate /jails/bind/20110315/var/log/messages
>> Apr 13 05:17:41 bind named[23534]: internal_send:
>> 192.168.50.145#65176: Cannot allocate memory
>> Jun 21 23:30:44 bind named[39864]: internal_send:
>> 192.168.50.251#36155: Cannot allocate memory
>> Jun 24 15:28:00 bind named[39864]: internal_send:
>> 192.168.50.251#28651: Cannot allocate memory
>> Jun 28 12:57:52 bind named[2462]: internal_send:
>> 192.168.165.154#1201: Cannot allocate memory
>>
>> My initial guess: it happens sooner or later somehow - whether it is
>> a lot of traffic in one go (ssh/scp copies of virtual disks) or a
>> lot of traffic over a longer period (a nameserver gets asked again
>> and again).
>
> Scott, are you also using jails? If both of you are: is there any
> possibility you can remove use of those? I'm not sure how VirtualBox
> fits into the picture (jails + VirtualBox that is), but I can imagine
> jails having different environmental constraints that might cause this.
>
> Basically the troubleshooting process here is to remove pieces of the
> puzzle until you figure out which piece is causing the issue. I don't
> want to get the NIC driver devs all spun up for something that, for
> example, might be an issue with the jail implementation.
No jails here.
I do have one bind error message in all my logs:
daemon:Jun 20 10:52:28 xeon named[399]: internal_send: 10.1.2.95#51946: Cannot allocate memory
Greping my logs for "allocate" turned up a handful of memory allocation errors with netatalk too.
afpd.log:Jul 01 16:13:04.828835 afpd[18303] {dsi_stream.c:427} (E:DSI): dsi_stream_send: Cannot allocate memory
afpd.log:Jun 23 13:34:01.000987 afpd[17970] {fork.c:980} (E:AFPDaemon): afp_read(final file.pdf): Cannot allocate memory
And a handful from samba:
[2011/07/05 23:43:22.483224, 0] lib/util_sock.c:675(write_data)
write_data: write failure in writing to client 10.1.1.10. Error Cannot allocate memory
[2011/07/05 23:43:22.493839, 0] smbd/process.c:79(srv_send_smb)
Error writing 51 bytes to client. -1. (Cannot allocate memory)
I haven't personally seen any errors on the client side with samba/netatalk (and when scp was failing regularly I transferred the same files over netatalk+samba without error) nor have I had any reports of problems, but I guess there's a good chance all these log messages are related.
I've been trying to trigger the scp failure remotely tonight with no luck. I was triggering it regularly during the work day today, but not tonight. I will try to experiment tomorrow during the day with stopping VirtualBox and removing the kernel modules and seeing what happens.
Scott
More information about the freebsd-stable
mailing list