any hope for nfe/msk?

[Pyun YongHyeon]

On Thu, Nov 01, 2007 at 10:59:48AM +0200, Oleg Lomaka wrote:
 > Hello,
 > 
 > Pyun YongHyeon wrote:
 > >On Tue, Oct 30, 2007 at 04:01:04PM +0200, Oleg Lomaka wrote:
 > >
 > >[...]
 > >
 > > > I had RxFIFO overrun again :(
 > > > from dmest:
 > > > msk0: Rx FIFO overrun!
 > >
 > >[...]
 > >
 > >Please try attached patch again. Sorry for the trouble.
 > >After applying the patch show me verbosed dmesg output related with
 > >msk(4)/PHY driver.
 > >
 > >Thanks for testing.
 > >  
 > pcib1: <MPTable PCI-PCI bridge> irq 16 at device 28.0 on pci0
 > pcib1:   domain            0
 > pcib1:   secondary bus     2
 > pcib1:   subordinate bus   2
 > pcib1:   I/O decode        0x2000-0x2fff
 > pcib1:   memory decode     0xd0100000-0xd01fffff
 > pcib1:   no prefetched decode
 > pci2: <PCI bus> on pcib1
 > pci2: domain=0, physical bus=2
 > found-> vendor=0x11ab, dev=0x4352, revid=0x14
 >        domain=0, bus=2, slot=0, func=0
 >        class=02-00-00, hdrtype=0x00, mfdev=0
 >        cmdreg=0x0007, statreg=0x4010, cachelnsz=16 (dwords)
 >        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
 >        intpin=a, irq=11
 >        powerspec 2  supports D0 D1 D2 D3  current D0
 >        MSI supports 2 messages, 64 bit
 >        map[10]: type Memory, range 64, base 0xd0100000, size 14, enabled
 > pcib1: requested memory range 0xd0100000-0xd0103fff: good
 >        map[18]: type I/O Port, range 32, base 0x2000, size  8, enabled
 > pcib1: requested I/O range 0x2000-0x20ff: in range
 > pcib1: slot 0 INTA routed to irq 16
 > mskc0: <Marvell Yukon 88E8038 Gigabit Ethernet> port 0x2000-0x20ff mem 
 > 0xd0100000-0xd0103fff irq 16 at device 0.0 on pci2
 > mskc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xd0100000
 > mskc0: MSI count : 2
 > mskc0: RAM buffer size : 4KB
 > mskc0: Port 0 : Rx Queue 2KB(0x00000000:0x000007ff)
 > mskc0: Port 0 : Tx Queue 2KB(0x00000800:0x00000fff)
 > msk0: <Marvell Technology Group Ltd. Yukon FE Id 0xb7 Rev 0x01> on mskc0
 > msk0: bpf attached
 > msk0: Ethernet address: 00:1b:24:0e:bc:26
 > miibus0: <MII bus> on msk0
 > e1000phy0: <Marvell 88E3082 10/100 Fast Ethernet PHY> PHY 0 on miibus0
 > e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 > ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49
 > mskc0: [MPSAFE]
 > mskc0: [FILTER]
 > 

So far all looks good to me. If you encounter watchdog timeouts
or Rx FIFO overruns let me know.

-- 
Regards,
Pyun YongHyeon