if_bge driver problem.

[husnu demir]

Nothing changed.


and the other infos;


Thanks for the quick response.
------------------------------------

root@~# ifconfig 
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
        inet6 fe80::211:9ff:fe9b:6a7d%bge0 prefixlen 64 scopeid 0x1 
        inet x.x.3.138 netmask 0xffffff80 broadcast x.x.3.255
        ether 00:11:09:9b:6a:7d
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
bge1: flags=8902<BROADCAST,PROMISC,SIMPLEX,MULTICAST> mtu 1500
        options=1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING>
        ether 00:04:76:f7:99:6e
        media: Ethernet autoselect (none)
        status: no carrier
bge2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=18<VLAN_MTU,VLAN_HWTAGGING>
        inet6 fe80::210:18ff:fe00:4d53%bge2 prefixlen 64 scopeid 0x3 
        inet x.x.2.2 netmask 0xffffff00 broadcast x.x.2.255
        ether 00:10:18:00:4d:53
        media: Ethernet autoselect (1000baseSX <full-duplex>)
        status: active
em0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        options=b<RXCSUM,TXCSUM,VLAN_MTU>
        ether 00:04:23:c2:dc:29
        media: Ethernet autoselect
        status: no carrier
pflog0: flags=0<> mtu 33208
pfsync0: flags=0<> mtu 2020
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet6 ::1 prefixlen 128 
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7 
        inet 127.0.0.1 netmask 0xff000000 
fatm0: flags=841<UP,RUNNING,SIMPLEX> mtu 9180
        inet x.x.16.130 netmask 0xfffffffc 
        inet x.x.17.2 netmask 0xfffffffc 
        media: ATM Multi-mode/155MBit
        status: active
root@~# pciconf -lv | grep -A 3 ^bge
bge0 at pci3:1:0:  class=0x020000 card=0x026f1014 chip=0x16a714e4 rev=0x02 hdr=0x00
    vendor   = 'Broadcom Corporation'
    device   = 'BCM5703X NetXtreme Gigabit Ethernet'
    class    = network
--
bge1 at pci3:2:0:  class=0x020000 card=0x100610b7 chip=0x164514e4 rev=0x15 hdr=0x00
    vendor   = 'Broadcom Corporation'
    device   = 'BCM5701 NetXtreme Gigabit Ethernet'
    class    = network
--
bge2 at pci3:3:0:  class=0x020000 card=0x000a14e4 chip=0x16a714e4 rev=0x02 hdr=0x00
    vendor   = 'Broadcom Corporation'
    device   = 'BCM5703X NetXtreme Gigabit Ethernet'
    class    = network




On Fri, Jan 27, 2006 at 06:34:39PM +0300, Gleb Smirnoff wrote:
> On Fri, Jan 27, 2006 at 02:24:38PM +0200, husnu demir wrote:
> h> Hi,
> h> 
> h> I upgraded my pc after "2006-01-25 FreeBSD-SA-06:06.kmem" issue. After that it also upgrade the bge drivers and now it is not working. In fact my "Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002" is not working. The other bge's working properly. Most probly last update may cause that. I have been using 6-STABLE.
> h> 
> h> I also tried to look at the switch part and find out that there are CRC Errors. The errors comes just after enabling the interface on the bsd box. After that there isnt any activity. Also when I sniff the interface with tcpdump, I saw lots of packets. Most probly, the driver did not let the further comminication after bad CRCs.
> 
> What happens if you disable hardware checksum offloading on your NIC?
> 
> ifconfig bge0 -rxcsum -txcsum
> 
> -- 
> Totus tuus, Glebius.
> GLEBIUS-RIPN GLEB-RIPE
> _______________________________________________
> freebsd-stable at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to "freebsd-stable-unsubscribe at freebsd.org"