FreeBSD 7.1-RELEASE working on Netra AX1105-500

[Gheorghe Ardelean]

Hi,

I have tested FreeBSD 7.1-RELEASE on a Netra AX1105-500 and it works quite
nicely. Attached is the dmesg.

Installing 7.0-RELEASE was not possible because of READ_BIG errors, in
7.1-RELEASE I am still getting some of them but the boot process continues
allowing me to do the rest of the installation over network (I did not
tested a CD only installation).

Pietro or Mark could you please add the attached dmesg to the dmesgs I
have already provided on sparc64 wiki?
(http://wiki.freebsd.org/FreeBSD/sparc64/dmesgs)

Thank you!

Best regards,

Gheorghe Ardelean.
-------------- next part --------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #0: Fri Jan  2 01:32:39 UTC 2009
    root at obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "tick" frequency 500000000 Hz quality 1000
real memory  = 536870912 (512 MB)
avail memory = 505643008 (482 MB)
cpu0: Sun Microsystems UltraSparc-IIe Processor (500.00 MHz CPU)
registered firmware set <isp_1000>
registered firmware set <isp_1040>
registered firmware set <isp_1040_it>
registered firmware set <isp_1080>
registered firmware set <isp_1080_it>
registered firmware set <isp_12160>
registered firmware set <isp_12160_it>
registered firmware set <isp_2100>
registered firmware set <isp_2200>
registered firmware set <isp_2300>
registered firmware set <isp_2322>
registered firmware set <isp_2400>
kbd0 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, REGOPS_FUNC)
nexus0: <Open Firmware Nexus device>
pcib0: <U2P UPA-PCI bridge> mem 0x1fe00000000-0x1fe0000ffff,0x1fe01000000-0x1fe010000ff irq 2032,2030,2031,2021 on nexus0
pcib0: Sabre, impl 0, version 0, IGN 0x1f, bus A, 66MHz
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [GIANT-LOCKED]
pcib0: [ITHREAD]
pcib0: DVMA map: 0xc0000000 to 0xc3ffffff
pcib0: [FILTER]
pci0: <OFW PCI bus> on pcib0
pcib1: <APB PCI-PCI bridge> at device 1.1 on pci0
pci1: <OFW PCI bus> on pcib1
ebus0: <PCI-EBus3 bridge> mem 0xf0000000-0xf0ffffff,0xf1000000-0xf17fffff at device 12.0 on pci1
ebus0: <idprom>: incomplete
ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no driver attached)
eeprom0: <EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0
eeprom0: model mk48t59
isab0: <PCI-ISA bridge> at device 7.0 on pci1
pcib0: guessing interrupt 0 for device 1.1 pin 1
isa0: <ISA bus> on isab0
gem0: <Sun ERI 10/100 Ethernet> mem 0xe0400000-0xe041ffff at device 12.1 on pci1
miibus0: <MII bus> on gem0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: 2kB RX FIFO, 2kB TX FIFO
gem0: Ethernet address: 00:03:ba:tt:xx:yy
gem0: [ITHREAD]
ohci0: <Sun PCIO-2 USB controller> mem 0xe2000000-0xe2007fff at device 12.3 on pci1
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <Sun PCIO-2 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 4 ports with 4 removable, self powered
pci1: <old, non-VGA display device> at device 3.0 (no driver attached)
atapci0: <AcerLabs M5229 UDMA66 controller> port 0x400-0x407,0x418-0x41b,0x410-0x417,0x408-0x40b,0x420-0x42f at device 13.0 on pci1
atapci0: [ITHREAD]
atapci0: using PIO transfers above 137GB as workaround for 48bit DMA access bug, expect reduced performance
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
gem1: <Sun ERI 10/100 Ethernet> mem 0xe0440000-0xe045ffff at device 5.1 on pci1
miibus1: <MII bus> on gem1
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem1: 2kB RX FIFO, 2kB TX FIFO
gem1: Ethernet address: 00:03:ba:tt:xx:zz
gem1: [ITHREAD]
ohci1: <Sun PCIO-2 USB controller> mem 0xe5000000-0xe5007fff at device 5.3 on pci1
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <Sun PCIO-2 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 4 ports with 4 removable, self powered
pcib2: <APB PCI-PCI bridge> at device 1.0 on pci0
pci2: <OFW PCI bus> on pcib2
nexus0: <syscons> type unknown (no driver attached)
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 43 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> at port 0x2e8-0x2ef irq 43 on isa0
uart1: [FILTER]
Timecounters tick every 1.000 msec
ad0: 3077MB <Seagate ST33232A 3.02> at ata2-master UDMA33
acd0: DVDR <ATAPI iHDP118 4/GL03> at ata3-master PIO4
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05 
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_Install.
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05 
Trying to mount root from ufs:/dev/ad0a
Invalid time in real time clock.
Check and reset the date immediately!