sa(4) driver changes available for test
Dan Langille
dan at langille.org
Mon Mar 2 16:44:11 UTC 2015
> On Mar 2, 2015, at 11:31 AM, Kenneth D. Merry <ken at FreeBSD.ORG> wrote:
>
> On Mon, Mar 02, 2015 at 11:09:57 -0500, Dan Langille wrote:
>>
>>> On Mar 1, 2015, at 9:29 PM, Kenneth D. Merry <ken at FreeBSD.ORG> wrote:
>>>
>>> On Sun, Mar 01, 2015 at 19:41:07 -0500, Dan Langille wrote:
>>>>
>>>>> On Mar 1, 2015, at 7:31 PM, Kenneth D. Merry <ken at FreeBSD.ORG> wrote:
>>>>>
>>>>> On Sun, Mar 01, 2015 at 19:15:05 -0500, Dan Langille wrote:
>>>>>>
>>>>>>> On Feb 17, 2015, at 1:36 PM, Kenneth D. Merry <ken at freebsd.org> wrote:
>>>>>>>
>>>>>>> On Sat, Feb 14, 2015 at 18:22:43 -0500, Dan Langille wrote:
>>>>>>>>
>>>>>>>>> On Feb 13, 2015, at 7:32 PM, Kenneth D. Merry <ken at freebsd.org> wrote:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> I have a fairly large set of changes to the sa(4) driver and mt(1) driver
>>>>>>>>> that I'm planning to commit in the near future.
>>>>>>>>>
>>>>>>>>> A description of the changes is here and below in this message.
>>>>>>>>>
>>>>>>>>> If you have tape hardware and the inclination, I'd appreciate testing and
>>>>>>>>> feedback.
>>>>>>>>
>>>>>>>> I have a DLT 8000 and an SDLT 220.
>>>>>>>>
>>>>>>>> I don't have anything running current, but I have a spare machine which I could use for testing.
>>>>>>>>
>>>>>>>> Do you see any value is tests with that hardware? I'd be testing it via Bacula.
>>>>>>>>
>>>>>>>> disclosure: I'm the sysutils/bacula-* maintainer and a Bacula committer.
>>>>>>>>
>>>>>>>
>>>>>>> Actually, yes. Bacula is a bit tricky to configure, so your trying it out
>>>>>>> would be helpful if you have the time.
>>>>>>>
>>>>>>> In looking at the manuals for both the SDLT 220 and the DLT 8000, they both
>>>>>>> claim to support long position information for the SCSI READ POSITION
>>>>>>> command.
>>>>>>>
>>>>>>> You can see what I'm talking about by doing:
>>>>>>>
>>>>>>> mt eod
>>>>>>> mt status
>>>>>>>
>>>>>>> On my DDS-4 tape drive, this shows:
>>>>>>>
>>>>>>> # mt -f /dev/nsa3 status
>>>>>>> Drive: sa3: <SEAGATE DAT 06240-XXX 8071> Serial Number: HJ00YWY
>>>>>>> ---------------------------------
>>>>>>> Mode Density Blocksize bpi Compression
>>>>>>> Current: 0x26:DDS-4 1024 bytes 97000 enabled (DCLZ)
>>>>>>> ---------------------------------
>>>>>>> Current Driver State: at rest.
>>>>>>> ---------------------------------
>>>>>>> Partition: 0 Calc File Number: -1 Calc Record Number: -1
>>>>>>> Residual: 0 Reported File Number: -1 Reported Record Number: -1
>>>>>>> Flags: None
>>>>>>>
>>>>>>> But on an LTO-5, which will give long position information, I get:
>>>>>>>
>>>>>>> [root at doc ~]# mt status
>>>>>>> Drive: sa0: <IBM ULTRIUM-HH5 E4J1>
>>>>>>> ---------------------------------
>>>>>>> Mode Density Blocksize bpi Compression
>>>>>>> Current: 0x58:LTO-5 variable 384607 enabled (0x1)
>>>>>>> ---------------------------------
>>>>>>> Current Driver State: at rest.
>>>>>>> ---------------------------------
>>>>>>> Partition: 0 Calc File Number: 2 Calc Record Number: -1
>>>>>>> Residual: 0 Reported File Number: 2 Reported Record Number: 32373
>>>>>>> Flags: None
>>>>>>>
>>>>>>> That, in combination with the changes I made to the position information
>>>>>>> code in the driver, mean that even the old MTIOCGET ioctl should return an
>>>>>>> accurate file number at end of data. e.g., on the LTO-5:
>>>>>>>
>>>>>>> [root at doc ~]# mt ostatus
>>>>>>> Mode Density Blocksize bpi Compression
>>>>>>> Current: 0x58:LTO-5 variable 384607 0x1
>>>>>>> ---------available modes---------
>>>>>>> 0: 0x58:LTO-5 variable 384607 0x1
>>>>>>> 1: 0x58:LTO-5 variable 384607 0x1
>>>>>>> 2: 0x58:LTO-5 variable 384607 0x1
>>>>>>> 3: 0x58:LTO-5 variable 384607 0x1
>>>>>>> ---------------------------------
>>>>>>> Current Driver State: at rest.
>>>>>>> ---------------------------------
>>>>>>> File Number: 2 Record Number: -1 Residual Count -1
>>>>>>>
>>>>>>> So the thing to try, in addition to just making sure that Bacula continues
>>>>>>> to work properly, is to try setting this for the tape drive in
>>>>>>> bacula-sd.conf:
>>>>>>>
>>>>>>> Hardware End of Medium = yes
>>>>>>>
>>>>>>> It looks like the Bacula tape program (btape) has a test mode, and it would
>>>>>>> be good to run through the tests on one of the tape drives and see whether
>>>>>>> they work, and whether the results are different before and after the
>>>>>>> changes. I'm not sure how to enable the test mode.
>>>>>>
>>>>>> I have this in /usr/local/etc/bacula/bacula-sd.conf
>>>>>>
>>>>>> Device {
>>>>>> Name = DLT
>>>>>> Description = "QUANTUM DLT7000 1624"
>>>>>> Media Type = DLT
>>>>>> Archive Device = /dev/nsa1
>>>>>>
>>>>>> Autochanger = YES
>>>>>> Drive Index = 0
>>>>>>
>>>>>> Offline On Unmount = no
>>>>>> Hardware End of Medium = yes
>>>>>> BSF at EOM = yes
>>>>>> Backward Space Record = no
>>>>>> Fast Forward Space File = no
>>>>>> TWO EOF = yes
>>>>>> }
>>>>>>
>>>>>> FYI, http://www.freebsddiary.org/digital-tl891.php (from 2006) has a btape test on this same model.
>>>>>>
>>>>>> Here's the test I ran tonight:
>>>>>>
>>>>>> [root at cuppy:/usr/home/dan] # btape -c /usr/local/etc/bacula/bacula-sd.conf /dev/nsa1
>>>>>> Tape block granularity is 1024 bytes.
>>>>>> btape: butil.c:287-0 Using device: "/dev/nsa1" for writing.
>>>>>> btape: btape.c:469-0 open device "DLT" (/dev/nsa1): OK
>>>>>> *test
>>>>>>
>>>>>> === Write, rewind, and re-read test ===
>>>>>>
>>>>>> I'm going to write 10000 records and an EOF
>>>>>> then write 10000 records and an EOF, then rewind,
>>>>>> and re-read the data to verify that it is correct.
>>>>>>
>>>>>> This is an *essential* feature ...
>>>>>>
>>>>>> btape: btape.c:1152-0 Wrote 10000 blocks of 64412 bytes.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1168-0 Wrote 10000 blocks of 64412 bytes.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1210-0 Rewind OK.
>>>>>> 10000 blocks re-read correctly.
>>>>>> Got EOF on tape.
>>>>>> 10000 blocks re-read correctly.
>>>>>> === Test Succeeded. End Write, rewind, and re-read test ===
>>>>>>
>>>>>> btape: btape.c:1277-0 Block position test
>>>>>> btape: btape.c:1289-0 Rewind OK.
>>>>>> Reposition to file:block 0:4
>>>>>> Block 5 re-read correctly.
>>>>>> Reposition to file:block 0:200
>>>>>> Block 201 re-read correctly.
>>>>>> Reposition to file:block 0:9999
>>>>>> Block 10000 re-read correctly.
>>>>>> Reposition to file:block 1:0
>>>>>> Block 10001 re-read correctly.
>>>>>> Reposition to file:block 1:600
>>>>>> Block 10601 re-read correctly.
>>>>>> Reposition to file:block 1:9999
>>>>>> Block 20000 re-read correctly.
>>>>>> === Test Succeeded. End Write, rewind, and re-read test ===
>>>>>>
>>>>>>
>>>>>>
>>>>>> === Append files test ===
>>>>>>
>>>>>> This test is essential to Bacula.
>>>>>>
>>>>>> I'm going to write one record in file 0,
>>>>>> two records in file 1,
>>>>>> and three records in file 2
>>>>>>
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:469-0 open device "DLT" (/dev/nsa1): OK
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1420-0 Now moving to end of medium.
>>>>>
>>>>> This is the critical piece. The test moves the tape to the end of the
>>>>> medium. With hardware position information, you can tell what filemark
>>>>> you're on. Without it, you can't.
>>>>>
>>>>>> btape: btape.c:622-0 tape_dev.c:345 ioctl MTIOCGET error on "DLT" (/dev/nsa1). ERR=No error: 0.
>>>>>> We should be in file 3. I am at file 0. This is NOT correct!!!!
>>>>>>
>>>>>> Append test failed. Attempting again.
>>>>>> Setting "Hardware End of Medium = no
>>>>>> and "Fast Forward Space File = no
>>>>>> and retrying append test.
>>>>>
>>>>> This is not surprsing, given that the drive doesn't support long read
>>>>> position data. (It's a SCSI-2 device.) So that means that Bacula will
>>>>> need to do it manually.
>>>>
>>>> Yes, I have nothing newer than SCSI-2. Even my SDLT is SCSI-2 but that
>>>> tape library is hooked up to a different computer and was doing backups today.
>>>
>>> So, here is one thing that we can try to see whether these drives support
>>> long position information, even though they only claim to be SCSI-2. If
>>> they do, we can potentially add a quirk (or autodetection) to enable it.
>>> The code currently doesn't bother asking drives that claim to be SCSI-2
>>> for long position information. (Because that feature was added in the
>>> SSC spec, which came after SCSI-2.)
>>>
>>> Issue a READ POSITION with the short form specified:
>>>
>>> camcontrol cmd sa1 -v -c "34 0 0 0 0 0 0 0 0 0" -i 20 - |hd
>>>
>>> Issue a READ POSITION with the vendor-specific block numbers:
>>>
>>> camcontrol cmd sa1 -v -c "34 1 0 0 0 0 0 0 0 0" -i 20 - |hd
>>>
>>> Issue a READ POSITION with the long form data:
>>>
>>> camcontrol cmd sa1 -v -c "34 6 0 0 0 0 0 0 0 0" -i 32 - |hd
>>>
>>> If it supports the last one, then I can put a quirk (or autodetection) in
>>> the driver and Bacula will get the hardware filemarks. You should try this
>>> on your SDLT as well. It may well support it.
>>
>> Sadly, no:
>>
>> [root at cuppy:~] # camcontrol cmd sa1 -v -c "34 0 0 0 0 0 0 0 0 0" -i 20 - |hd
>> 00000000 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000010 00 00 00 00 |....|
>> 00000014
>> [root at cuppy:~] # camcontrol cmd sa1 -v -c "34 1 0 0 0 0 0 0 0 0" -i 20 - |hd
>> 00000000 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000010 00 00 00 00 |....|
>> 00000014
>> [root at cuppy:~] # camcontrol cmd sa1 -v -c "34 6 0 0 0 0 0 0 0 0" -i 32 - |hd
>> camcontrol: error sending command
>> (pass2:ahc0:0:2:0): READ POSITION. CDB: 34 06 00 00 00 00 00 00 00 00
>> (pass2:ahc0:0:2:0): CAM status: SCSI Status Error
>> (pass2:ahc0:0:2:0): SCSI status: Check Condition
>> (pass2:ahc0:0:2:0): SCSI sense: ILLEGAL REQUEST asc:24,0 (Invalid field in CDB)
>> (pass2:ahc0:0:2:0): Command byte 1 bit 2 is invalid
>> [root at cuppy:~] #
>
> Okay. Not too surprising I suppose.
>
>> The SDLT server is on 9.3 though:
>>
>> [root at knew:/usr/home/dan] # camcontrol cmd sa1 -v -c "34 0 0 0 0 0 0 0 0 0" -i 20 - |hd
>> camcontrol: cam_lookup_pass: CAMGETPASSTHRU ioctl failed
>> cam_lookup_pass: No such file or directory
>> cam_lookup_pass: either the pass driver isn't in your kernel
>> cam_lookup_pass: or sa1 doesn't exist
>> [root at knew:/usr/home/dan] # uname -a
>> FreeBSD knew.unixathome.org 9.3-RELEASE-p10 FreeBSD 9.3-RELEASE-p10 #0: Tue Feb 24 21:28:03 UTC 2015 root at amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
>> [root at knew:/usr/home/dan] #
>>
>>
>> It took me a while to figure that out... there is no sa1 on *this* system.
>>
>> But, my SDLT:
>>
>> [root at knew:/usr/home/dan] # camcontrol cmd sa0 -v -c "34 0 0 0 0 0 0 0 0 0" -i 20 - |hd
>> 00000000 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000010 00 00 00 00 |....|
>> 00000014
>> [root at knew:/usr/home/dan] # camcontrol cmd sa0 -v -c "34 1 0 0 0 0 0 0 0 0" -i 20 - |hd
>> 00000000 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000010 00 00 00 00 |....|
>> 00000014
>> [root at knew:/usr/home/dan] # camcontrol cmd sa0 -v -c "34 6 0 0 0 0 0 0 0 0" -i 32 - |hd
>> 00000000 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
>> 00000020
>> [root at knew:/usr/home/dan] #
>
> Just to confirm, can you send the output of:
>
> camcontrol inquiry sa0 -v
>
> I want to make certain it reports that it is SCSI-2. If so, I'll change
> the check in the driver to try asking for long position information on
> SCSI-2 devices. If it fails, it'll fall back to the regular method.
[dan at knew:~] $ sudo camcontrol inquiry sa0 -v
pass10: <COMPAQ SuperDLT1 5F5F> Removable Sequential Access SCSI-2 device
pass10: Serial Number CXB46H0716
pass10: 80.000MB/s transfers (40.000MHz, offset 31, 16bit)
[dan at knew:~] $
>
>>>
>>> Google didn't quickly produce a SCSI manual for the DEC drive, but the
>>> Quantum SDLT manual indicates that it supports long position data, despite
>>> identifying itself as a SCSI-2 drive.
>>>
>>>>> === Append files test ===
>>>>>>
>>>>>> This test is essential to Bacula.
>>>>>>
>>>>>> I'm going to write one record in file 0,
>>>>>> two records in file 1,
>>>>>> and three records in file 2
>>>>>>
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:469-0 open device "DLT" (/dev/nsa1): OK
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1420-0 Now moving to end of medium.
>>>>>> btape: btape.c:625-0 Moved to end of medium.
>>>>>> We should be in file 3. I am at file 3. This is correct!
>>>>>>
>>>>>> Now the important part, I am going to attempt to append to the tape.
>>>>>>
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> Done appending, there should be no I/O errors
>>>>>>
>>>>>> Doing Bacula scan of blocks:
>>>>>> 1 block of 64448 bytes in file 1
>>>>>> End of File mark.
>>>>>> 2 blocks of 64448 bytes in file 2
>>>>>> End of File mark.
>>>>>> 3 blocks of 64448 bytes in file 3
>>>>>> End of File mark.
>>>>>> 1 block of 64448 bytes in file 4
>>>>>> End of File mark.
>>>>>> Total files=4, blocks=7, bytes = 451,136
>>>>>> End scanning the tape.
>>>>>> We should be in file 4. I am at file 4. This is correct!
>>>>>>
>>>>>>
>>>>>> It looks like the test worked this time, please add:
>>>>>>
>>>>>> Hardware End of Medium = No
>>>>>>
>>>>>> Fast Forward Space File = No
>>>>>> to your Device resource in the Storage conf file.
>>>>>>
>>>>>> The above Bacula scan should have output identical to what follows.
>>>>>> Please double check it ...
>>>>>> === Sample correct output ===
>>>>>> 1 block of 64448 bytes in file 1
>>>>>> End of File mark.
>>>>>> 2 blocks of 64448 bytes in file 2
>>>>>> End of File mark.
>>>>>> 3 blocks of 64448 bytes in file 3
>>>>>> End of File mark.
>>>>>> 1 block of 64448 bytes in file 4
>>>>>> End of File mark.
>>>>>> Total files=4, blocks=7, bytes = 451,136
>>>>>> === End sample correct output ===
>>>>>>
>>>>>> If the above scan output is not identical to the
>>>>>> sample output, you MUST correct the problem
>>>>>> or Bacula will not be able to write multiple Jobs to
>>>>>> the tape.
>>>>>>
>>>>>> Skipping read backwards test because BSR turned off.
>>>>>>
>>>>>>
>>>>>> === Forward space files test ===
>>>>>>
>>>>>> This test is essential to Bacula.
>>>>>>
>>>>>> I'm going to write five files then test forward spacing
>>>>>>
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1907-0 Wrote one record of 64412 bytes.
>>>>>> btape: btape.c:1909-0 Wrote block to device.
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:604-0 Wrote 1 EOF to "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1634-0 Now forward spacing 1 file.
>>>>>> We should be in file 1. I am at file 1. This is correct!
>>>>>> btape: btape.c:1646-0 Now forward spacing 2 files.
>>>>>> We should be in file 3. I am at file 3. This is correct!
>>>>>> btape: btape.c:574-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1659-0 Now forward spacing 4 files.
>>>>>> We should be in file 4. I am at file 4. This is correct!
>>>>>>
>>>>>> btape: btape.c:1677-0 Now forward spacing 1 more file.
>>>>>> We should be in file 5. I am at file 5. This is correct!
>>>>>>
>>>>>> === End Forward space files test ===
>>>>>>
>>>>>>
>>>>>> Ah, I see you have an autochanger configured.
>>>>>> To test the autochanger you must have a blank tape
>>>>>> that I can write on in Slot 1.
>>>>>>
>>>>>> Do you wish to continue with the Autochanger test? (y/n): y
>>>>>>
>>>>>>
>>>>>> === Autochanger test ===
>>>>>>
>>>>>> 3301 Issuing autochanger "loaded" command.
>>>>>> Nothing loaded in the drive. OK.
>>>>>> 3303 Issuing autochanger "load 1 0" command.
>>>>>> 3303 Autochanger "load 1 0" status is OK.
>>>>>> btape: btape.c:469-0 open device "DLT" (/dev/nsa1): OK
>>>>>> btape: btape.c:1564-0 Rewound "DLT" (/dev/nsa1)
>>>>>> btape: btape.c:1571-0 Wrote EOF to "DLT" (/dev/nsa1)
>>>>>>
>>>>>> The test autochanger worked!!
>>>>>
>>>>> Great, thanks for running the test! Looks like things are working as well
>>>>> as they were before.
>>>>>
>>>>>>>
>>>>>>>> I'll let the other Bacula devs know about this. They deal with the hardware. I work on PostgreSQL.
>>>>>>>>
>>>>>>>
>>>>>>> Thanks! If there are additional features they would like out of the tape
>>>>>>> driver, I'm happy to talk about it. (Or help if they'd like to use the new
>>>>>>> status reporting ioctl, MTIOCEXTGET or any of the other new ioctls.)
>>>>>>
>>>>>> Errors are interesting to me. Especially corrected errors. They are a good indicator of tape quality.
>>>>>>
>>>>>
>>>>> Yes. At least on modern drives, there is a good bit available in the log
>>>>> pages. You can try seeing what logs your drive supports by installing the
>>>>> sg3_utils package and running 'sg_logs sa1 --all'.
>>>>>
>>>>> Given the large amount of data available on some drives, and the difficulty
>>>>> distilling it down to a clear good/bad, I probably won't stick that in the
>>>>> 'mt status' output.
>>>>>
>>>>> But you can certainly take a look at it and have an idea of whether your
>>>>> particular tape/drive are experiencing issues.
>>>>
>>>> That's a lot of output: https://gist.github.com/dlangille/0e15a7fbf7acab56fd32
>>>
>>> That is a lot.
>>>
>>>> I will run some Bacula jobs soon. I'm still setting up config files.
>>>
>>> Thanks for all the testing, I really appreciate it!
>>>
>>> Ken
>>> --
>>> Kenneth Merry
>>> ken at FreeBSD.ORG
>>
>> ?
>> Dan Langille
>> http://langille.org/
>>
>>
>>
>>
>>
>
> Ken
> --
> Kenneth Merry
> ken at FreeBSD.ORG
—
Dan Langille
http://langille.org/
More information about the freebsd-scsi
mailing list