LSI SAS 3008 card - 35 out of 36 disks detected
Justin O'Conor
oconnor at crystal.harvard.edu
Mon Dec 8 15:58:20 UTC 2014
Hi All,
Thanks, this is encouraging. smp_discover ses0|1 see 36 sata disks. This is from the 10.1 install.
Lets start with the short ones -
root at rhea:~ # sg_inq --hex --len=64 ses0
00 0d 00 05 02 34 00 40 02 4c 53 49 20 20 20 20 20 ....4. at .LSI
10 53 41 53 32 58 33 36 20 20 20 20 20 20 20 20 20 SAS2X36
20 30 65 31 32 78 33 36 2d 35 35 2e 31 34 2e 31 38 0e12x36-55.14.18
30 2e 30 00 20 20 20 20 20 .0.
root at rhea:~ # sg_inq --hex --len=64 ses1
00 0d 00 05 02 34 00 40 02 4c 53 49 20 20 20 20 20 ....4. at .LSI
10 53 41 53 32 58 32 38 20 20 20 20 20 20 20 20 20 SAS2X28
20 30 65 31 32 78 33 36 2d 35 35 2e 31 34 2e 31 38 0e12x36-55.14.18
30 2e 30 00 20 20 20 20 20
root at rhea:~ # smp_discover ses0
phy 0:S:attached:[500605b009150c20:02 i(SSP+STP+SMP)] 6 Gbps
phy 1:S:attached:[500605b009150c20:03 i(SSP+STP+SMP)] 6 Gbps
phy 2:S:attached:[500605b009150c20:01 i(SSP+STP+SMP)] 6 Gbps
phy 3:S:attached:[500605b009150c20:00 i(SSP+STP+SMP)] 6 Gbps
phy 4:U:attached:[50030480017bd5bf:00 exp t(SMP)] 6 Gbps
phy 5:U:attached:[50030480017bd5bf:01 exp t(SMP)] 6 Gbps
phy 6:U:attached:[50030480017bd5bf:02 exp t(SMP)] 6 Gbps
phy 7:U:attached:[50030480017bd5bf:03 exp t(SMP)] 6 Gbps
phy 12:U:attached:[50030480017ae20c:00 t(SATA)] 6 Gbps
phy 13:U:attached:[50030480017ae20d:00 t(SATA)] 6 Gbps
phy 14:U:attached:[50030480017ae20e:00 t(SATA)] 6 Gbps
phy 15:U:attached:[50030480017ae20f:00 t(SATA)] 6 Gbps
phy 16:U:attached:[50030480017ae210:00 t(SATA)] 6 Gbps
phy 17:U:attached:[50030480017ae211:00 t(SATA)] 6 Gbps
phy 18:U:attached:[50030480017ae212:00 t(SATA)] 6 Gbps
phy 19:U:attached:[50030480017ae213:00 t(SATA)] 6 Gbps
phy 20:U:attached:[50030480017ae214:00 t(SATA)] 6 Gbps
phy 21:U:attached:[50030480017ae215:00 t(SATA)] 6 Gbps
phy 22:U:attached:[50030480017ae216:00 t(SATA)] 6 Gbps
phy 23:U:attached:[50030480017ae217:00 t(SATA)] 6 Gbps
phy 24:U:attached:[50030480017ae218:00 t(SATA)] 6 Gbps
phy 25:U:attached:[50030480017ae219:00 t(SATA)] 6 Gbps
phy 26:U:attached:[50030480017ae21a:00 t(SATA)] 6 Gbps
phy 27:U:attached:[50030480017ae21b:00 t(SATA)] 6 Gbps
phy 28:U:attached:[50030480017ae21c:00 t(SATA)] 6 Gbps
phy 29:U:attached:[50030480017ae21d:00 t(SATA)] 6 Gbps
phy 30:U:attached:[50030480017ae21e:00 t(SATA)] 6 Gbps
phy 31:U:attached:[50030480017ae21f:00 t(SATA)] 6 Gbps
phy 32:U:attached:[50030480017ae220:00 t(SATA)] 6 Gbps
phy 33:U:attached:[50030480017ae221:00 t(SATA)] 6 Gbps
phy 34:U:attached:[50030480017ae222:00 t(SATA)] 6 Gbps
phy 35:U:attached:[50030480017ae223:00 t(SATA)] 6 Gbps
phy 36:D:attached:[50030480017ae23d:00 V i(SSP+SMP) t(SSP)] 6 Gbps
root at rhea:~ # foreach PHY ( `seq 0 1 36` )
foreach? smp_discover -p $PHY ses0
foreach? end
Discover response:
expander change count: 1328
phy identifier: 0
attached device type: SAS or SATA device
attached reason: power on
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=1 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x500605b009150c20
attached phy identifier: 2
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 33
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x500605b009150c20
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 1
attached device type: SAS or SATA device
attached reason: power on
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=1 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x500605b009150c20
attached phy identifier: 3
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 33
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x500605b009150c20
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 2
attached device type: SAS or SATA device
attached reason: power on
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=1 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x500605b009150c20
attached phy identifier: 1
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 33
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x500605b009150c20
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 3
attached device type: SAS or SATA device
attached reason: power on
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=1 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x500605b009150c20
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 33
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x500605b009150c20
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 4
attached device type: expander device
attached reason: SMP phy control requested
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017bd5bf
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 4
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017bd5bf
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 5
attached device type: expander device
attached reason: SMP phy control requested
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017bd5bf
attached phy identifier: 1
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 4
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017bd5bf
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 6
attached device type: expander device
attached reason: SMP phy control requested
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017bd5bf
attached phy identifier: 2
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 4
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017bd5bf
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 7
attached device type: expander device
attached reason: SMP phy control requested
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017bd5bf
attached phy identifier: 3
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 4
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017bd5bf
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 8
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 9
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 10
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 11
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 12
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae20c
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 13
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae20d
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 1
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 14
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae20e
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 2
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 15
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae20f
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 3
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 16
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae210
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 4
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 17
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae211
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 5
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 18
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae212
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 6
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 19
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae213
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 7
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 20
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae214
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 8
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 21
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae215
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 9
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 22
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae216
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 10
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 23
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae217
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 11
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 24
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae218
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 12
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 25
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae219
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 13
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 26
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21a
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 48
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 14
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 27
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21b
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 49
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 15
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 28
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21c
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 16
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 29
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21d
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 17
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 30
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21e
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 18
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 31
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae21f
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 19
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 32
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae220
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 20
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 33
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae221
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 21
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 34
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae222
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 22
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 35
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae223
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 45
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 23
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 1328
phy identifier: 36
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=0 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=1 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017ae23f
attached SAS address: 0x50030480017ae23d
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 6 Gbps
hardware minimum physical link rate: 6 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 1
partial pathway timeout value: 7 us
routing attribute: direct
connector type: SAS virtual connector [max 1 phy]
connector element index: 24
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 1
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
root at rhea:~ # smp_discover ses1
phy 0:S:attached:[50030480017ae23f:04 exp t(SMP)] 6 Gbps
phy 1:S:attached:[50030480017ae23f:05 exp t(SMP)] 6 Gbps
phy 2:S:attached:[50030480017ae23f:06 exp t(SMP)] 6 Gbps
phy 3:S:attached:[50030480017ae23f:07 exp t(SMP)] 6 Gbps
phy 8:D:disabled
phy 9:D:disabled
phy 10:D:disabled
phy 11:D:disabled
phy 12:U:attached:[50030480017bd5ac:00 t(SATA)] 6 Gbps
phy 13:U:attached:[50030480017bd5ad:00 t(SATA)] 6 Gbps
phy 14:U:attached:[50030480017bd5ae:00 t(SATA)] 6 Gbps
phy 15:U:attached:[50030480017bd5af:00 t(SATA)] 6 Gbps
phy 16:U:attached:[50030480017bd5b0:00 t(SATA)] 6 Gbps
phy 17:U:attached:[50030480017bd5b1:00 t(SATA)] 6 Gbps
phy 18:U:attached:[50030480017bd5b2:00 t(SATA)] 6 Gbps
phy 19:U:attached:[50030480017bd5b3:00 t(SATA)] 6 Gbps
phy 20:U:attached:[50030480017bd5b4:00 t(SATA)] 6 Gbps
phy 21:U:attached:[50030480017bd5b5:00 t(SATA)] 6 Gbps
phy 22:U:attached:[50030480017bd5b6:00 t(SATA)] 6 Gbps
phy 23:U:attached:[50030480017bd5b7:00 t(SATA)] 6 Gbps
phy 24:D:disabled
phy 25:D:disabled
phy 26:D:disabled
phy 27:D:disabled
phy 28:D:attached:[50030480017bd5bd:00 V i(SSP+SMP) t(SSP)] 6 Gbps
root at rhea:~ # foreach PHY ( `seq 0 1 28` )
foreach? smp_discover -p $PHY ses1
foreach? end
Discover response:
expander change count: 241
phy identifier: 0
attached device type: expander device
attached reason: loss of dword synchronization
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017ae23f
attached phy identifier: 4
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017ae23f
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 1
attached device type: expander device
attached reason: loss of dword synchronization
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017ae23f
attached phy identifier: 5
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017ae23f
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 2
attached device type: expander device
attached reason: loss of dword synchronization
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017ae23f
attached phy identifier: 6
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017ae23f
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 3
attached device type: expander device
attached reason: loss of dword synchronization
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=1 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017ae23f
attached phy identifier: 7
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 1
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: subtractive
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x50030480017ae23f
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 1
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 4
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 5
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 6
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 7
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled; unknown
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 8
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 9
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 10
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 11
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 12
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5ac
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 21
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 13
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5ad
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 19
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 1
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 14
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5ae
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 19
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 2
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 15
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5af
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 3
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 16
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 19
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 4
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 17
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b1
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 5
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 18
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b2
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 6
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 19
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b3
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 7
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 20
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b4
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 8
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 21
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b5
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 9
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 22
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b6
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 10
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 23
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=1
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5b7
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 18
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: table
connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys]
connector element index: 11
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 24
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 25
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 26
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 27
attached device type: no device attached
attached reason: unknown
negotiated logical link rate: phy disabled
attached initiator: ssp=0 stp=0 smp=0 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=0 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x0
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 1.5 Gbps
hardware minimum physical link rate: 1.5 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 0
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 0
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy disabled
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
Discover response:
expander change count: 241
phy identifier: 28
attached device type: SAS or SATA device
attached reason: unknown
negotiated logical link rate: phy enabled, 6 Gbps
attached initiator: ssp=1 stp=0 smp=1 sata_host=0
attached sata port selector: 0
STP buffer too small: 0
attached target: ssp=1 stp=0 smp=0 sata_device=0
SAS address: 0x50030480017bd5bf
attached SAS address: 0x50030480017bd5bd
attached phy identifier: 0
attached persistent capable: 0
attached power capable: 0
attached slumber capable: 0
attached partial capable: 0
attached inside ZPSDS persistent: 0
attached requested inside ZPSDS: 0
attached break_reply capable: 0
attached pwr_dis capable: 0
programmed minimum physical link rate: 6 Gbps
hardware minimum physical link rate: 6 Gbps
programmed maximum physical link rate: 6 Gbps
hardware maximum physical link rate: 6 Gbps
phy change count: 1
virtual phy: 1
partial pathway timeout value: 7 us
routing attribute: direct
connector type: No information
connector element index: 0
connector physical link: 0
phy power condition: 0
sas power capable: 0
sas slumber capable: 0
sas partial capable: 0
sata slumber capable: 0
sata partial capable: 0
pwr_dis signal: 0
pwr_dis control capable: 0
sas slumber enabled: 0
sas partial enabled: 0
sata slumber enabled: 0
sata partial enabled: 0
attached device name: 0x0
requested inside ZPSDS changed by expander: 0
inside ZPSDS persistent: 0
requested inside ZPSDS: 0
zone group persistent: 1
inside ZPSDS: 1
zoning enabled: 0
zone group: 1
self-configuration status: 0
self-configuration levels completed: 0
self-configuration sas address: 0x0
programmed phy capabilities: 0x0
current phy capabilities: 0x0
attached phy capabilities: 0x0
reason: unknown
negotiated physical link rate: phy enabled, 6 Gbps
optical mode enabled: 0
negotiated SSC: 0
hardware muxing supported: 0
default inside ZPSDS persistent: 0
default requested inside ZPSDS: 0
default zone group persistent: 1
default zoning enabled: 0
default zone group: 1
saved inside ZPSDS persistent: 0
saved requested inside ZPSDS: 0
saved zone group persistent: 1
saved zoning enabled: 0
saved zone group: 1
shadow inside ZPSDS persistent: 0
shadow requested inside ZPSDS: 0
shadow zone group persistent: 1
shadow zoning enabled: 0
shadow zone group: 1
device slot number: 255
device slot group number: 255
device slot group output connector:
root at rhea:~ #
On Dec 5, 2014, at 5:05 PM, Alan Somers <asomers at freebsd.org> wrote:
> I had a very similar problem that ended up being a bug in the expander
> firmware. It was exposed by the mpr(4) driver because that driver
> enumerates drives differently than mps(4) or Linux. Please install
> sysutils.smp_utils and post the output of "smp_discover -p $PHY $DEV"
> where $DEV is each expander (probably ses0 and ses1) and $PHY is every
> phy on each expander. You can see the list of phys by doing
> "smp_discover $DEV" without the "-p" option. Also, would you mind
> running "sg_inq --hex --len=64 $DEV" so I know what we're working
> with?
>
> -Alan
>
More information about the freebsd-scsi
mailing list