mps questions
Borja Marcos
borjam at sarenet.es
Wed Jan 26 10:17:01 UTC 2011
On Jan 20, 2011, at 6:00 PM, Kenneth D. Merry wrote:
> If you see all the disks in the LSI BIOS, it most likely means there is a
> driver bug that is keeping FreeBSD from seeing all the disks.
>
> Try booting with -v (boot -v at the boot loader prompt) and send the full
> dmesg output. That will cause the driver to print some additional
> information when it probes.
>
> After that, try booting with hw.mps.N.debug_level=1 set in loader.conf,
> where N is either 0 or 1, depending on which mps instance is having the
> problem.
>
> You can turn it off via sysctl after you boot.
Sorry, more complete output follows. boot -v and debug enabled for the driver.
I've omitted plenty of "mps0: writing postindex NNN" messages
# cat /var/run/dmesg.boot | fgrep -v "mps0: writing postindex"
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=6
map[20]: type I/O Port, range 32, base 0xec80, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 21
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xec80
found-> vendor=0x8086, dev=0x3a35, revid=0x00
domain=0, bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=5
map[20]: type I/O Port, range 32, base 0xeca0, size 5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 20
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xeca0
found-> vendor=0x8086, dev=0x3a36, revid=0x00
domain=0, bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=6
map[20]: type I/O Port, range 32, base 0xecc0, size 5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 21
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xecc0
found-> vendor=0x8086, dev=0x3a39, revid=0x00
domain=0, bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
map[20]: type I/O Port, range 32, base 0xece0, size 5, enabled
pcib0: matched entry for 0.29.INTD
pcib0: slot 29 INTD hardwired to IRQ 20
unknown: Reserved 0x20 bytes for rid 0x20 type 4 at 0xece0
found-> vendor=0x8086, dev=0x3a3a, revid=0x00
domain=0, bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0146, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=6
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xdf0ff000, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 21
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdf0ff000
found-> vendor=0x8086, dev=0x244e, revid=0x90
domain=0, bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3a16, revid=0x00
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xda000000-0xddffffff
pcib1: no prefetched decode
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x14e4, dev=0x163b, revid=0x20
domain=0, bus=1, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 3 supports D0 D3 current D0
MSI supports 16 messages, 64 bit
MSI-X supports 9 messages in map 0x10
map[10]: type Memory, range 64, base 0xda000000, size 25, enabled
pcib1: requested memory range 0xda000000-0xdbffffff: good
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 36
found-> vendor=0x14e4, dev=0x163b, revid=0x20
domain=0, bus=1, slot=0, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=14
powerspec 3 supports D0 D3 current D0
MSI supports 16 messages, 64 bit
MSI-X supports 9 messages in map 0x10
map[10]: type Memory, range 64, base 0xdc000000, size 25, enabled
pcib1: requested memory range 0xdc000000-0xddffffff: good
pcib1: matched entry for 1.0.INTB
pcib1: slot 0 INTB hardwired to IRQ 48
bce0: <Broadcom NetXtreme II BCM5716 1000Base-T (C0)> mem 0xda000000-0xdbffffff irq 36 at device 0.0 on pci1
bce0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xda000000
bce0: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 256 to local APIC 32 vector 64
bce0: using IRQ 256 for MSI
miibus0: <MII bus> on bce0
brgphy0: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: OUI 0x0050ef, model 0x003c, rev. 8
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce0: bpf attached
bce0: Ethernet address: 84:2b:2b:73:12:1f
bce0: [MPSAFE]
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.10)
bce1: <Broadcom NetXtreme II BCM5716 1000Base-T (C0)> mem 0xdc000000-0xddffffff irq 48 at device 0.1 on pci1
bce1: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xdc000000
bce1: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 257 to local APIC 32 vector 80
bce1: using IRQ 257 for MSI
miibus1: <MII bus> on bce1
brgphy1: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: OUI 0x0050ef, model 0x003c, rev. 8
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce1: bpf attached
bce1: Ethernet address: 84:2b:2b:73:12:20
bce1: [MPSAFE]
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.10)
pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xffff
pcib2: memory decode 0xdf100000-0xdf2fffff
pcib2: no prefetched decode
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x1000, dev=0x0072, revid=0x02
domain=0, bus=2, slot=0, func=0
class=01-07-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
MSI-X supports 15 messages in map 0x14
map[10]: type I/O Port, range 32, base 0xfc00, size 8, enabled
pcib2: requested I/O range 0xfc00-0xfcff: in range
map[14]: type Memory, range 64, base 0xdf2b0000, size 16, enabled
pcib2: requested memory range 0xdf2b0000-0xdf2bffff: good
map[1c]: type Memory, range 64, base 0xdf2c0000, size 18, enabled
pcib2: requested memory range 0xdf2c0000-0xdf2fffff: good
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 32
mps0: <LSI SAS2008> port 0xfc00-0xfcff mem 0xdf2b0000-0xdf2bffff,0xdf2c0000-0xdf2fffff irq 32 at device 0.0 on pci2
mps0: Reserved 0x10000 bytes for rid 0x14 type 3 at 0xdf2b0000
mps0: Doorbell= 0x22000000
mps0: Doorbell= 0x12000000
mps0: IOCFacts :
MsgVersion: 0x200
HeaderVersion: 0xb00
IOCNumber: 0
IOCExceptions: 0x0
MaxChainDepth: 96
WhoInit: ROM BIOS
NumberOfPorts: 1
RequestCredit: 3439
ProductID: 0x2713
IOCCapabilities: 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
FWVersion= 2-15-63-0
IOCRequestFrameSize: 32
MaxInitiators: 1
MaxTargets: 40
MaxSasExpanders: 20
MaxEnclosures: 10
ProtocolFlags: 3<ScsiTarg,ScsiInit>
HighPriorityCredit: 63
MaxReplyDescriptorPostQueueDepth: 65520
ReplyFrameSize: 32
MaxVolumes: 2
MaxDevHandle: 79
MaxPersistentEntries: 128
mps0: Firmware: 02.15.63.00
mps0: IOCCapabilities: 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
mps0: Doorbell= 0x10000000
mps0: Doorbell= 0x10000000
mps0: IOCInit status= 0x0
mps0: PortFacts :
PortNumber: 0
PortType: 0x30
MaxPostedCmdBuffers: 0
mps0: attempting to allocate 1 MSI-X vectors (15 supported)
msi: routing MSI-X IRQ 258 to local APIC 32 vector 49
mps0: using IRQ 258 for MSI-X
mps0: [MPSAFE]
mps0: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xf000-0xfff
pcib3: no prefetched decode
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
pcib4: <ACPI PCI-PCI bridge> at device 9.0 on pci0
pcib4: domain 0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0xf000-0xfff
pcib4: no prefetched decode
pci4: <ACPI PCI bus> on pcib4
pci4: domain=0, physical bus=4
pcib5: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib5: domain 0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xf000-0xfff
pcib5: no prefetched decode
pci5: <ACPI PCI bus> on pcib5
pci5: domain=0, physical bus=5
pci0: <base peripheral, interrupt controller> at device 20.0 (no driver attached)
pci0: <base peripheral, interrupt controller> at device 20.1 (no driver attached)
pci0: <base peripheral, interrupt controller> at device 20.2 (no driver attached)
uhci0: <Intel 82801JI (ICH10) USB controller USB-D> port 0xec40-0xec5f irq 17 at device 26.0 on pci0
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 32 vector 50
uhci0: [MPSAFE]
uhci0: [ITHREAD]
usbus0: <Intel 82801JI (ICH10) USB controller USB-D> on uhci0
uhci1: <Intel 82801JI (ICH10) USB controller USB-E> port 0xec60-0xec7f irq 18 at device 26.1 on pci0
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 32 vector 51
uhci1: [MPSAFE]
uhci1: [ITHREAD]
usbus1: <Intel 82801JI (ICH10) USB controller USB-E> on uhci1
ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem 0xdf0fe000-0xdf0fe3ff irq 19 at device 26.7 on pci0
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 32 vector 52
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <Intel 82801JI (ICH10) USB 2.0 controller USB-B> on ehci0
uhci2: <Intel 82801JI (ICH10) USB controller USB-A> port 0xec80-0xec9f irq 21 at device 29.0 on pci0
ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 32 vector 53
uhci2: [MPSAFE]
uhci2: [ITHREAD]
usbus3: <Intel 82801JI (ICH10) USB controller USB-A> on uhci2
uhci3: <Intel 82801JI (ICH10) USB controller USB-B> port 0xeca0-0xecbf irq 20 at device 29.1 on pci0
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 32 vector 54
uhci3: [MPSAFE]
uhci3: [ITHREAD]
usbus4: <Intel 82801JI (ICH10) USB controller USB-B> on uhci3
uhci4: <Intel 82801JI (ICH10) USB controller USB-C> port 0xecc0-0xecdf irq 21 at device 29.2 on pci0
uhci4: [MPSAFE]
uhci4: [ITHREAD]
usbus5: <Intel 82801JI (ICH10) USB controller USB-C> on uhci4
uhci5: <Intel 82801JI (ICH10) USB controller USB-F> port 0xece0-0xecff irq 20 at device 29.3 on pci0
uhci5: [MPSAFE]
uhci5: [ITHREAD]
usbus6: <Intel 82801JI (ICH10) USB controller USB-F> on uhci5
ehci1: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xdf0ff000-0xdf0ff3ff irq 21 at device 29.7 on pci0
ehci1: [MPSAFE]
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib6: domain 0
pcib6: secondary bus 6
pcib6: subordinate bus 6
pcib6: I/O decode 0xf000-0xfff
pcib6: memory decode 0xde000000-0xdeffffff
pcib6: prefetched decode 0xd9800000-0xd9ffffff
pcib6: Subtractively decoded bridge.
pci6: <ACPI PCI bus> on pcib6
pci6: domain=0, physical bus=6
found-> vendor=0x102b, dev=0x0532, revid=0x0a
domain=0, bus=6, slot=3, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=10
powerspec 1 supports D0 D3 current D0
map[10]: type Prefetchable Memory, range 32, base 0xd9800000, size 23, enabled
pcib6: requested memory range 0xd9800000-0xd9ffffff: good
map[14]: type Memory, range 32, base 0xde7fc000, size 14, enabled
pcib6: requested memory range 0xde7fc000-0xde7fffff: good
map[18]: type Memory, range 32, base 0xde800000, size 23, enabled
pcib6: requested memory range 0xde800000-0xdeffffff: good
pcib6: matched entry for 6.3.INTA
pcib6: slot 3 INTA hardwired to IRQ 19
vgapci0: <VGA-compatible display> mem 0xd9800000-0xd9ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19 at device 3.0 on pci6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 4 hz: 14318180 opts: legacy_route 64-bit
Timecounter "HPET" frequency 14318180 Hz quality 900
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 32 vector 55
uart0: [FILTER]
uart0: fast interrupt
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 32 vector 56
uart1: [FILTER]
uart1: fast interrupt
qpi0: <QPI system bus> on motherboard
acpi0: wakeup code va 0xffffff8241e8c000 pa 0x4000
ex_isa_identify()
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
isa_probe_children: disabling PnP devices
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xd2000-0xd2fff,0xec000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 32 vector 57
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0045
psm0: failed to reset the aux device.
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
isa_probe_children: probing PnP devices
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 11
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 10
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 11
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 11
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 11
device_attach: est4 attach returned 6
p4tcc4: <CPU Frequency Thermal Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 11
device_attach: est5 attach returned 6
p4tcc5: <CPU Frequency Thermal Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 10
device_attach: est6 attach returned 6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 10
device_attach: est7 attach returned 6
p4tcc7: <CPU Frequency Thermal Control> on cpu7
Device configuration finished.
procfs registered
ZFS filesystem version 5
ZFS storage pool version 28
lapic: Divisor 2, Frequency 66669411 Hz
Timecounter "TSC" frequency 2133421199 Hz quality -100
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
hptrr: no controller detected.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
mps0: SAS Device Page 0 :
Slot: 8
EnclosureHandle: 0x1
SASAddress: 0x5942b0b0558ac200
ParentDevHandle: 0x1
PhyNum: 8
AccessStatus: 0x0
DevHandle: 0x9
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: 4801<Direct,SepDev>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 0
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
Expander found at enclosure 2
mps0: SAS Device Page 0 :
Slot: 0
EnclosureHandle: 0x2
SASAddress: 0x500065b36789abff
ParentDevHandle: 0x1
PhyNum: 0
AccessStatus: 0x0
DevHandle: 0xa
AttachedPhyIdentifier: 0x13
ZoneGroup: 0
DeviceInfo: 1902<SmpTarg,Direct,LsiDev>,Edge Expander
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 8
DeviceName: 0xb3650050ffab8967
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 0
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c4f7d2d
ParentDevHandle: 0xa
PhyNum: 2
AccessStatus: 0x0
DevHandle: 0xb
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 4
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c4f6ec1
ParentDevHandle: 0xa
PhyNum: 3
AccessStatus: 0x0
DevHandle: 0xc
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 5
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c4f7425
ParentDevHandle: 0xa
PhyNum: 4
AccessStatus: 0x0
DevHandle: 0xd
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 1
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c4f7875
ParentDevHandle: 0xa
PhyNum: 5
AccessStatus: 0x0
DevHandle: 0xe
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 2
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c54578d
ParentDevHandle: 0xa
PhyNum: 6
AccessStatus: 0x0
DevHandle: 0xf
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 3
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c545701
ParentDevHandle: 0xa
PhyNum: 7
AccessStatus: 0x0
DevHandle: 0x10
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 7
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c5454bd
ParentDevHandle: 0xa
PhyNum: 10
AccessStatus: 0x0
DevHandle: 0x11
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 6
EnclosureHandle: 0x2
SASAddress: 0x5000c5002c4f5561
ParentDevHandle: 0xa
PhyNum: 16
AccessStatus: 0x0
DevHandle: 0x12
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: c01<SspTarg,Direct>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS Device Page 0 :
Slot: 24
EnclosureHandle: 0x2
SASAddress: 0x500065b36789abfd
ParentDevHandle: 0xa
PhyNum: 24
AccessStatus: 0x0
DevHandle: 0x13
AttachedPhyIdentifier: 0x0
ZoneGroup: 0
DeviceInfo: 4c41<SspInit,SspTarg,Direct,SepDev>,End Device
Flags: 0x1
PhysicalPort: 0
MaxPortConnections: 1
DeviceName: 0x0
PortGroups: 4
DmaGroup: 0
ControlGroup: 4
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 19
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <1902<SmpTarg,Direct,LsiDev>,Edge Expander> <6.0Gbps> <0x000a> <2/0>
mps0: Triggering rescan of 0:0:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 21
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x000b> <2/0>
mps0: Triggering rescan of 0:1:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 20
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x000c> <2/4>
mps0: Triggering rescan of 0:4:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 15
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x000d> <2/5>
mps0: Triggering rescan of 0:5:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 14
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x000e> <2/1>
mps0: Triggering rescan of 0:2:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 13
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x000f> <2/2>
mps0: Triggering rescan of 0:3:-1
mps0: SAS PHY Page 0 :
OwnerDevHandle: 0x0001
AttachedDevHandle: 0x000a
AttachedPhyIdentifier: 12
AttachedPhyInfo Reason: Loss DWORD Sync (0x14)
ProgrammedLinkRate: 6.0Gbps (0xa8)
HwLinkRate: 6.0Gbps (0xa8)
ChangeCount: 1
Flags: 0x1
PhyInfo Reason: Power On (0x10000)
NegotiatedLinkRate: 6.0Gbps (0xaa)
mps0: Found device <c01<SspTarg,Direct>,End Device> <6.0Gbps> <0x0010> <2/3>
mps0: Triggering rescan of 0:6:-1
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
mps0: mpssas_discovery_end: removing confighook
ugen2.2: <vendor 0x0424> at usbus2
uhub8: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/0.00, addr 2> on usbus2
ugen7.2: <Generic> at usbus7
umass0: <Generic Mass Storage, class 0/0, rev 2.00/1.41, addr 2> on usbus7
umass0: SCSI over Bulk-Only; quirks = 0x4101
uhub8: 4 ports with 4 removable, self powered
umass0:1:0:-1: Attached to scbus1
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?ugen2.3: <Dell> at usbus2
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
ukbd0: <EP1 Interrupt> on usbus2
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable errorkbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
mps0: (0:0:0) IOCStatus= 0x43, ScsiStatus= 0x0, SCSIState= 0x4 TransferCount= 0x0
(probe0:mps0:0:0:0): Error 22, Unretryable error
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0x11
mps0: (0:4:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:1:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:3:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:2:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:5:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
mps0: (0:6:0) IOCStatus= 0x45, ScsiStatus= 0x0, SCSIState= 0x0 TransferCount= 0xc
pass0 at mps0 bus 0 scbus0 target 1 lun 0
pass0: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass0: Serial Number 6SJ0642S
pass0: 600.000MB/s transfers
pass0: Command Queueing enabled
pass1 at mps0 bus 0 scbus0 target 2 lun 0
pass1: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass1: Serial Number 6SJ06F4Z
pass1: 600.000MB/s transfers
pass1: Command Queueing enabled
pass2 at mps0 bus 0 scbus0 target 3 lun 0
pass2: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass2: Serial Number 6SJ07AMF
pass2: 600.000MB/s transfers
pass2: Command Queueing enabled
pass3 at mps0 bus 0 scbus0 target 4 lun 0
pass3: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass3: Serial Number 6SJ06T5C
pass3: 600.000MB/s transfers
pass3: Command Queueing enabled
pass4 at mps0 bus 0 scbus0 target 5 lun 0
pass4: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass4: Serial Number 6SJ06T75
pass4: 600.000MB/s transfers
pass4: Command Queueing enabled
pass5 at mps0 bus 0 scbus0 target 6 lun 0
pass5: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
pass5: Serial Number 6SJ07AP9
pass5: 600.000MB/s transfers
pass5: Command Queueing enabled
pass6 at umass-sim0 bus 0 scbus1 target 0 lun 0
pass6: <Alcor Flash Disk 8.07> Removable Direct Access SCSI-2 device
pass6: Serial Number 09FE0AAE
pass6: 40.000MB/s transfers
da0 at mps0 bus 0 scbus0 target 1 lun 0
da0: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da0: Serial Number 6SJ0642S
da0: 600.000MB/s transfers
da0: Command Queueing enabled
da0: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da1 at mps0 bus 0 scbus0 target 2 lun 0
da1: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da1: Serial Number 6SJ06F4Z
da1: 600.000MB/s transfers
da1: Command Queueing enabled
da1: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da2 at mps0 bus 0 scbus0 target 3 lun 0
da2: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da2: Serial Number 6SJ07AMF
da2: 600.000MB/s transfers
da2: Command Queueing enabled
da2: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
da3 at mps0 bus 0 scbus0 target 4 lun 0
da3: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da3: Serial Number 6SJ06T5C
da3: 600.000MB/s transfers
da3: Command Queueing enabled
da3: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da4 at mps0 bus 0 scbus0 target 5 lun 0
da4: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da4: Serial Number 6SJ06T75
da4: 600.000MB/s transfers
da4: Command Queueing enabled
da4: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da5 at mps0 bus 0 scbus0 target 6 lun 0
da5: <SEAGATE ST3300657SS-H EH02> Fixed Direct Access SCSI-5 device
da5: Serial Number 6SJ07AP9
da5: 600.000MB/s transfers
da5: Command Queueing enabled
da5: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
(da6:umass-sim0:0:0:0): SCSI status error
(da6:umass-sim0:0:0:0): READ CAPACITY(10). CDB: 25 0 0 0 0 0 0 0 0 0
(da6:umass-sim0:0:0:0): CAM status: SCSI Status Error
(da6:umass-sim0:0:0:0): SCSI status: Check Condition
(da6:umass-sim0:0:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed)
(da6:umass-sim0:0:0:0): Retrying command (per sense data)
da6 at umass-sim0 bus 0 scbus1 target 0 lun 0
da6: <Alcor Flash Disk 8.07> Removable Direct Access SCSI-2 device
da6: Serial Number 09FE0AAE
da6: 40.000MB/s transfers
da6: 976MB (1998848 512 byte sectors: 64H 32S/T 976C)
GEOM: new disk da3
GEOM: new disk da4
GEOM: new disk da5
GEOM: new disk da6
ATA PseudoRAID loaded
llaappiicc3354:: CCMMCCII uunnmmaasskkededlllalaaappppiiiciccc550515:3:2 :: C CCMCMCMCCIMII C uIun nmuumansnmkmaeadassskkeedkded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x21000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000100f2
SMP: AP CPU #2 Launched!
cpu2 AP:
ID: 0x22000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #4 Launched!
cpu4 AP:
ID: 0x32000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #3 Launched!
cpu3 AP:
ID: 0x23000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #6 Launched!
cpu6 AP:
ID: 0x34000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #5 Launched!
cpu5 AP:
ID: 0x33000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #7 Launched!
cpu7 AP:
ID: 0x35000000 VER: 0x01060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 33 vector 48
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 34 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 35 vector 48
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 50 vector 48
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 51 vector 48
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 52 vector 48
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 53 vector 48
msi: Assigning MSI IRQ 256 to local APIC 33 vector 49
msi: Assigning MSI IRQ 257 to local APIC 34 vector 49
msi: Assigning MSI-X IRQ 258 to local APIC 35 vector 49
Trying to mount root from ufs:/dev/da8s1a
ROOT MOUNT ERROR:
If you have invalid mount options, reboot, and first try the following from
the loader prompt:
set vfs.root.mountfrom.options=rw
and then remove invalid mount options from /etc/fstab.
Loader variables:
vfs.root.mountfrom=ufs:/dev/da8s1a
vfs.root.mountfrom.options=
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
eg. cd9660:/dev/acd0
This is equivalent to: mount -t cd9660 /dev/acd0 /
? List valid disk boot devices
<empty line> Abort manual input
mountroot> ufs:/dewv/\^H \^H\^H \^H\^H \^Hv/da6s1a
Trying to mount root from ufs:/dev/da6s1a
WARNING: / was not properly dismounted
ct_to_ts([2011-01-26 10:58:35]) = 1296039515.000000000
start_init: trying /sbin/init
WARNING: / was not properly dismounted
#
More information about the freebsd-scsi
mailing list