mptutil shows two volumes as with index 0

[pluknet]

Hi.

Seen on xSeries x3550 M2 with IBM SR-BR10i (C1068E).
This is FreeBSD 8.1 amd64.

HW config and further info below.

# dmesg | grep mpt
mpt0: <LSILogic SAS/SATA Adapter> port 0x1000-0x10ff mem
0x97910000-0x97913fff,0x97900000-0x9790ffff irq 16 at device 0.0 on
pci1
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.20.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 2 Active Volumes (2 Max)
mpt0: 4 Hidden Drive Members (14 Max)
mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares )
mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:5:0): Primary Online
      (mpt0:1:6:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:6:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:5:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
(mpt0:0:7): Physical (mpt0:0:7:0), Pass-thru (mpt0:1:2:0)
(mpt0:0:7): Online
(mpt0:0:4): Physical (mpt0:0:4:0), Pass-thru (mpt0:1:3:0)
(mpt0:0:4): Online
(xpt0:mpt0:1:-1:-1): rescan already queued
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da1 at mpt0 bus 0 scbus0 target 2 lun 0

mpt0 at pci0:1:0:0:        class=0x010000 card=0x03941014 chip=0x00581000
rev=0x08 hdr=0x00
    vendor     = 'LSI Logic (Was: Symbios Logic, NCR)'
    device     = 'SAS 3000 series, 8-port with 1068E -StorPort'
    class      = mass storage
    subclass   = SCSI
    cap 01[50] = powerspec 2  supports D0 D1 D2 D3  current D0
    cap 10[68] = PCI-Express 1 endpoint max data 128(4096) link x4(x8)
    cap 05[98] = MSI supports 1 message, 64 bit
    cap 11[b0] = MSI-X supports 1 message in map 0x14

# mptutil show config
mpt0 Configuration: 2 volumes, 4 drives
    volume 0 (136G) RAID-1 OPTIMAL spans:
        drive 1 (137G) ONLINE <IBM-ESXS MBD2147RC SB18> SAS
        drive 0 (137G) ONLINE <IBM-ESXS MBD2147RC SB18> SAS
        spare pools: 0
    volume 0 (29G) RAID-1 OPTIMAL spans:
        drive 2 (30G) ONLINE <SSDSA2SH032G1GN 8850> SATA
        drive 3 (30G) ONLINE <SSDSA2SH032G1GN 8850> SATA
        spare pools: 0

# mptutil show volumes
mpt0 Volumes:
  Id     Size    Level   Stripe  State  Write-Cache  Name
     0 (  136G) RAID-1          OPTIMAL   Enabled
     0 (   29G) RAID-1          OPTIMAL   Disabled

# mptutil show drives
mpt0 Physical Drives:
   0 (  137G) ONLINE <IBM-ESXS MBD2147RC SB18> SAS bus 0 id 6
   1 (  137G) ONLINE <IBM-ESXS MBD2147RC SB18> SAS bus 0 id 5
   2 (   30G) ONLINE <SSDSA2SH032G1GN 8850> SATA bus 0 id 7
   3 (   30G) ONLINE <SSDSA2SH032G1GN 8850> SATA bus 0 id 4

# camcontrol devlist
<LSILOGIC Logical Volume 3000>     at scbus0 target 0 lun 0 (da0,pass0)
<LSILOGIC Logical Volume 3000>     at scbus0 target 2 lun 0 (da1,pass1)


-- 
wbr,
pluknet