kern/146287: [ciss] ciss(4) cannot see more than one
SmartArray controller
Sean Bruno
seanbru at yahoo-inc.com
Thu May 6 18:20:35 UTC 2010
On Thu, 2010-05-06 at 10:41 -0700, Ulf Zimmermann wrote:
> On Thu, May 06, 2010 at 09:58:50AM -0700, Sean Bruno wrote:
> > On Wed, 2010-05-05 at 18:47 -0700, Ulf Zimmermann wrote:
> > > > > Ok, found a machine and hooked it up. DL380 g4, has single port Qlogic Fibre
> > > > > channel HBA in slot 1 and 2 right now. What version should I install? 8-REL?
> > > > > Current?
> > > > >
> > > >
> > > > Current if you please.
> > > >
> > > > sean
> > >
> > > Turns out the iLO on the system I first grabbed is busted, so I grabbed
> > > another one. DL380 g4 with SmartArray P600 in slot 2 (middle) and a LSI
> > > 1030 based U320 controller in slot 3 (top). Both show up on -CURRENT:
> > >
> > > ciss0: <HP Smart Array 6i> port 0x4000-0x40ff mem 0xfdef0000-0xfdef1fff,0xfde80000-0xfdebffff irq 51 at device 3.0 on pci4
> > > ciss0: PERFORMANT Transport
> > > ciss0: got 0 MSI messages]
> > > ciss0: [ITHREAD]
> > > ciss1: <HP Smart Array P600> port 0x5400-0x54ff mem 0xfdfb0000-0xfdfb1fff,0xfdf40000-0xfdf7ffff irq 78 at device 2.0 on pci6
> > > ciss1: PERFORMANT Transport
> > > ciss1: got 0 MSI messages]
> > > ciss1: [ITHREAD]
> > > da0 at ciss0 bus 0 scbus0 target 0 lun 0
> > > mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x5000-0x50ff mem 0xfdfe0000-0xfdffffff,0xfdfc0000-0xfdfdffff irq 74 at device 1.0 on pci6
> > >
> > >
> > >
> >
> > So putting a card into the slot that failed on the previous machine
> > works now? Madness.
> >
> > Can you check that both machines are running the same BIOS rev and then
> > dump the dmesg+pciconf of the "new" machine here as well?
> >
> > Sean
> >
> >
>
> Remember I am not the same person, who reported the failure. I pulled out an
> older server, which we retired, to help potential fix the problem the reporter
> had with the bridge for slot 2.
>
> Here is the dmesg from verbose logging boot:
>
> Copyright (c) 1992-2010 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 9.0-CURRENT-201004 #0: Tue Apr 6 16:57:13 UTC 2010
> root at obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
> WARNING: WITNESS option enabled, expect reduced performance.
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc1157000.
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Calibrating TSC clock ... TSC clock: 3000118380 Hz
> CPU: Intel(R) Xeon(TM) CPU 3.00GHz (3000.12-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0xf43 Family = f Model = 4 Stepping = 3
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x641d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,CX16,xTPR>
> AMD Features=0x20000000<LM>
> TSC: P-state invariant
>
> Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries
> Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
> 1st-level data cache: 16 KB, 8-way set associative, sectored cache, 64 byte line size
> Trace cache: 12K-uops, 8-way set associative
> 2nd-level cache: 2-MB, 8-way set associative, 64-byte line size
> L2 cache: 2048 kbytes, 8-way associative, 64 bytes/line
> real memory = 10737418240 (10240 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009dfff, 643072 bytes (157 pages)
> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
> 0x0000000001426000 - 0x00000000dc08dfff, 3670441984 bytes (896104 pages)
> avail memory = 3668942848 (3498 MB)
> Table 'FACP' at 0xdfff3380
> Table 'SPCR' at 0xdfff3140
> Table 'MCFG' at 0xdfff31c0
> Table 'APIC' at 0xdfff3200
> APIC: Found table at 0xdfff3200
> MP Configuration Table version 1.4 found at 0xc00f2781
> APIC: Using the MADT enumerator.
> MADT: Found CPU APIC ID 0 ACPI ID 0: enabled
> SMP: Added CPU 0 (AP)
> MADT: Found CPU APIC ID 4 ACPI ID 4: disabled
> MADT: Found CPU APIC ID 2 ACPI ID 2: disabled
> MADT: Found CPU APIC ID 6 ACPI ID 6: enabled
> SMP: Added CPU 6 (AP)
> MADT: Found CPU APIC ID 1 ACPI ID 1: disabled
> MADT: Found CPU APIC ID 5 ACPI ID 5: disabled
> MADT: Found CPU APIC ID 3 ACPI ID 3: disabled
> MADT: Found CPU APIC ID 7 ACPI ID 7: disabled
> ACPI APIC Table: <HP 00000083>
> INTR: Adding local APIC 6 as a target
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 6
> x86bios: IVT 0x000000-0x0004ff at 0xc0000000
> x86bios: SSEG 0x010000-0x01ffff at 0xc6dad000
> x86bios: EBDA 0x09e000-0x09ffff at 0xc009e000
> x86bios: ROM 0x0a0000-0x0effff at 0xc00a0000
> APIC: CPU 0 has ACPI ID 0
> APIC: CPU 1 has ACPI ID 6
> bios32: Found BIOS32 Service Directory header at 0xc00ffee0
> bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
> pcibios: PCI BIOS entry at 0xf0000+0x96
> pnpbios: Found PnP BIOS data at 0xc00f4f90
> pnpbios: Entry = f0000:5faf Rev = 1.0
> Other BIOS signatures found:
> ULE: setup cpu 0
> ULE: setup cpu 1
> ACPI: RSDP 0xf4f00 00024 (v2 HP )
> ACPI: XSDT 0xdfff3300 00044 (v1 HP P51 00000002 ?? 0000162E)
> ACPI: FACP 0xdfff3380 000F4 (v3 HP P51 00000002 ?? 0000162E)
> ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 (20100331/tbfadt-707)
> ACPI: DSDT 0xdfff3480 02D62 (v1 HP DSDT 00000001 INTL 20030228)
> ACPI: FACS 0xdfff3100 00040
> ACPI: SPCR 0xdfff3140 00050 (v1 HP SPCRRBSU 00000001 ?? 0000162E)
> ACPI: MCFG 0xdfff31c0 0003C (v1 HP ProLiant 00000001 00000000)
> ACPI: APIC 0xdfff3200 000C2 (v1 HP 00000083 00000002 00000000)
> MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
> ioapic0: Routing external 8259A's -> intpin 0
> MADT: Found IO APIC ID 9, Interrupt 24 at 0xfec80000
> MADT: Found IO APIC ID 10, Interrupt 48 at 0xfec80400
> MADT: Found IO APIC ID 11, Interrupt 72 at 0xfec84000
> MADT: Found IO APIC ID 12, Interrupt 96 at 0xfec84400
> MADT: Interrupt override: source 0, irq 2
> ioapic0: Routing IRQ 0 -> intpin 2
> MADT: Interrupt override: source 9, irq 9
> ioapic0: intpin 9 trigger: level
> lapic: Routing NMI -> LINT1
> lapic: LINT1 trigger: edge
> lapic: LINT1 polarity: high
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> ioapic1 <Version 2.0> irqs 24-47 on motherboard
> ioapic2 <Version 2.0> irqs 48-71 on motherboard
> ioapic3 <Version 2.0> irqs 72-95 on motherboard
> ioapic4 <Version 2.0> irqs 96-119 on motherboard
> cpu0 BSP:
> ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
> wlan: <802.11 Link Layer>
> nfslock: pseudo-device
> kbd: new array size 4
> kbd1 at kbdmux0
> mem: <memory>
> Pentium Pro MTRR support enabled
> io: <I/O>
> null: <null device, zero device>
> random: <entropy source, Software, Yarrow>
> hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
> npx0: INT 16 interface
> acpi0: <HP P51> on motherboard
> PCIe: Memory Mapped configuration base @ 0xe0000000
> pcibios: BIOS version 2.10
> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
> acpi0: [MPSAFE]
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> acpi0: wakeup code va 0xc6da7000 pa 0x1000
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: \\_SB_.PCI0.CFG0.MEM0 -> bus 0 dev 0 func 0
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: \\_SB_.PCI0.PTC0.PCXC.SHP0 -> bus 5 dev 0 func 0
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: \\_SB_.PCI0.IBRG.ICH5 -> bus 0 dev 31 func 0
> ACPI timer: 0/4 0/5 0/5 0/5 0/5 0/5 0/453 0/5 0/5 0/5 -> 0
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu0: switching to generic Cx mode
> cpu1: <ACPI CPU> on acpi0
> pci_link0: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link1: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link2: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link3: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link4: Index IRQ Rtd Ref IRQs
> Initial Probe 0 255 N 0 5 7 10 11
> Validation 0 255 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link5: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link6: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pci_link7: Index IRQ Rtd Ref IRQs
> Initial Probe 0 5 N 0 5 7 10 11
> Validation 0 5 N 0 5 7 10 11
> After Disable 0 255 N 0 5 7 10 11
> pcib0: <ACPI Host-PCI bridge> on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pci0: domain=0, physical bus=0
> found-> vendor=0x8086, dev=0x3590, revid=0x0c
> domain=0, bus=0, slot=0, func=0
> class=06-00-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0146, statreg=0x0090, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found-> vendor=0x8086, dev=0x3595, revid=0x0c
> domain=0, bus=0, slot=2, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=255
> powerspec 2 supports D0 D3 current D0
> MSI supports 2 messages
> found-> vendor=0x8086, dev=0x3599, revid=0x0c
> domain=0, bus=0, slot=6, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=255
> powerspec 2 supports D0 D3 current D0
> MSI supports 2 messages
> found-> vendor=0x8086, dev=0x24d2, revid=0x02
> domain=0, bus=0, slot=29, func=0
> class=0c-03-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> map[20]: type I/O Port, range 32, base 0x2000, size 5, enabled
> pcib0: matched entry for 0.29.INTA
> pcib0: slot 29 INTA hardwired to IRQ 16
> found-> vendor=0x8086, dev=0x24d4, revid=0x02
> domain=0, bus=0, slot=29, func=1
> class=0c-03-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=b, irq=5
> map[20]: type I/O Port, range 32, base 0x2020, size 5, enabled
> pcib0: matched entry for 0.29.INTB
> pcib0: slot 29 INTB hardwired to IRQ 19
> found-> vendor=0x8086, dev=0x24d7, revid=0x02
> domain=0, bus=0, slot=29, func=2
> class=0c-03-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=c, irq=5
> map[20]: type I/O Port, range 32, base 0x2040, size 5, enabled
> pcib0: matched entry for 0.29.INTC
> pcib0: slot 29 INTC hardwired to IRQ 18
> found-> vendor=0x8086, dev=0x24de, revid=0x02
> domain=0, bus=0, slot=29, func=3
> class=0c-03-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> map[20]: type I/O Port, range 32, base 0x2060, size 5, enabled
> pcib0: matched entry for 0.29.INTA
> pcib0: slot 29 INTA hardwired to IRQ 16
> found-> vendor=0x8086, dev=0x24dd, revid=0x02
> domain=0, bus=0, slot=29, func=7
> class=0c-03-20, hdrtype=0x00, mfdev=0
> cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=d, irq=5
> powerspec 2 supports D0 D3 current D0
> map[10]: type Memory, range 32, base 0xfbef0000, size 10, enabled
> pcib0: matched entry for 0.29.INTD
> pcib0: slot 29 INTD hardwired to IRQ 23
> found-> vendor=0x8086, dev=0x244e, revid=0xc2
> domain=0, bus=0, slot=30, func=0
> class=06-04-00, hdrtype=0x01, mfdev=0
> cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> found-> vendor=0x8086, dev=0x24d0, revid=0x02
> domain=0, bus=0, slot=31, func=0
> class=06-01-00, hdrtype=0x00, mfdev=1
> cmdreg=0x014f, statreg=0x0280, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found-> vendor=0x8086, dev=0x24db, revid=0x02
> domain=0, bus=0, slot=31, func=1
> class=01-01-8a, hdrtype=0x00, mfdev=0
> cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=255
> map[20]: type I/O Port, range 32, base 0x500, size 4, enabled
> map[24]: type Memory, range 32, base 0, size 10, memory disabled
> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pcib1: domain 0
> pcib1: secondary bus 2
> pcib1: subordinate bus 4
> pcib1: I/O decode 0x4000-0x4fff
> pcib1: memory decode 0xfdd00000-0xfdefffff
> pcib1: no prefetched decode
> pci2: <ACPI PCI bus> on pcib1
> pci2: domain=0, physical bus=2
> found-> vendor=0x8086, dev=0x0329, revid=0x09
> domain=0, bus=2, slot=0, func=0
> class=06-04-00, hdrtype=0x01, mfdev=1
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> powerspec 2 supports D0 D3 current D0
> MSI supports 1 message, 64 bit
> found-> vendor=0x8086, dev=0x032a, revid=0x09
> domain=0, bus=2, slot=0, func=2
> class=06-04-00, hdrtype=0x01, mfdev=1
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> powerspec 2 supports D0 D3 current D0
> MSI supports 1 message, 64 bit
> pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci2
> pcib2: domain 0
> pcib2: secondary bus 3
> pcib2: subordinate bus 3
> pcib2: I/O decode 0xf000-0xfff
> pcib2: memory decode 0xfdd00000-0xfddfffff
> pcib2: no prefetched decode
> pci3: <ACPI PCI bus> on pcib2
> pci3: domain=0, physical bus=3
> found-> vendor=0x14e4, dev=0x1648, revid=0x10
> domain=0, bus=3, slot=1, func=0
> class=02-00-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> powerspec 2 supports D0 D3 current D0
> MSI supports 8 messages, 64 bit
> map[10]: type Memory, range 64, base 0xfddf0000, size 16, enabled
> pcib2: requested memory range 0xfddf0000-0xfddfffff: good
> pcib1: requested memory range 0xfddf0000-0xfddfffff: good
> pcib2: matched entry for 3.1.INTA
> pcib2: slot 1 INTA hardwired to IRQ 25
> found-> vendor=0x14e4, dev=0x1648, revid=0x10
> domain=0, bus=3, slot=1, func=1
> class=02-00-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
> intpin=b, irq=5
> powerspec 2 supports D0 D3 current D0
> MSI supports 8 messages, 64 bit
> map[10]: type Memory, range 64, base 0xfdde0000, size 16, enabled
> pcib2: requested memory range 0xfdde0000-0xfddeffff: good
> pcib1: requested memory range 0xfdde0000-0xfddeffff: good
> pcib2: matched entry for 3.1.INTB
> pcib2: slot 1 INTB hardwired to IRQ 26
> pci0:3:1:0: bad VPD cksum, remain 19
> bge0: <HP NC7782 Gigabit Server Adapter, ASIC rev. 0x002100> mem 0xfddf0000-0xfddfffff irq 25 at device 1.0 on pci3
> bge0: CHIP ID 0x00002100; ASIC REV 0x02; CHIP REV 0x21; PCI-X
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus0
> brgphy0: OUI 0x000818, model 0x0019, rev. 0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> bge0: bpf attached
> bge0: Ethernet address: 00:18:fe:70:86:d5
> ioapic1: routing intpin 1 (PCI IRQ 25) to lapic 0 vector 49
> bge0: [MPSAFE]
> bge0: [ITHREAD]
> pci0:3:1:1: bad VPD cksum, remain 19
> bge1: <HP NC7782 Gigabit Server Adapter, ASIC rev. 0x002100> mem 0xfdde0000-0xfddeffff irq 26 at device 1.1 on pci3
> bge1: CHIP ID 0x00002100; ASIC REV 0x02; CHIP REV 0x21; PCI-X
> miibus1: <MII bus> on bge1
> brgphy1: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy1: OUI 0x000818, model 0x0019, rev. 0
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
> bge1: bpf attached
> bge1: Ethernet address: 00:18:fe:70:86:d4
> ioapic1: routing intpin 2 (PCI IRQ 26) to lapic 0 vector 50
> bge1: [MPSAFE]
> bge1: [ITHREAD]
> pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci2
> pcib3: domain 0
> pcib3: secondary bus 4
> pcib3: subordinate bus 4
> pcib3: I/O decode 0x4000-0x4fff
> pcib3: memory decode 0xfde00000-0xfdefffff
> pcib3: no prefetched decode
> pci4: <ACPI PCI bus> on pcib3
> pci4: domain=0, physical bus=4
> found-> vendor=0x0e11, dev=0x0046, revid=0x01
> domain=0, bus=4, slot=3, func=0
> class=01-04-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0157, statreg=0x0230, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> powerspec 2 supports D0 D1 D3 current D0
> map[10]: type Memory, range 64, base 0xfdef0000, size 13, enabled
> pcib3: requested memory range 0xfdef0000-0xfdef1fff: good
> pcib1: requested memory range 0xfdef0000-0xfdef1fff: good
> map[18]: type I/O Port, range 32, base 0x4000, size 8, enabled
> pcib3: requested I/O range 0x4000-0x40ff: in range
> pcib1: requested I/O range 0x4000-0x40ff: in range
> map[1c]: type Memory, range 64, base 0xfde80000, size 18, enabled
> pcib3: requested memory range 0xfde80000-0xfdebffff: good
> pcib1: requested memory range 0xfde80000-0xfdebffff: good
> pcib3: matched entry for 4.3.INTA
> pcib3: slot 3 INTA hardwired to IRQ 51
> ciss0: <HP Smart Array 6i> port 0x4000-0x40ff mem 0xfdef0000-0xfdef1fff,0xfde80000-0xfdebffff irq 51 at device 3.0 on pci4
> ciss0: PERFORMANT Transport
> ciss0: got 0 MSI messages]
> ioapic2: routing intpin 3 (PCI IRQ 51) to lapic 0 vector 51
> ciss0: [MPSAFE]
> ciss0: [ITHREAD]
> ciss0: using 1024 of 1024 available commands
> ciss0: firmware 2.84
> ciss0: 2 SCSI channels
> ciss0: signature 'CISS'
> ciss0: valence 1
> ciss0: supported I/O methods 0x80000006<simple,performant>
> ciss0: active I/O method 0x5<performant>
> ciss0: 4G page base 0x00000000
> ciss0: interrupt coalesce delay 0us
> ciss0: interrupt coalesce count 16
> ciss0: max outstanding commands 1024
> ciss0: bus types 0x4
> ciss0: server name ''
> ciss0: heartbeat 0x59
> ciss0: 3 physical devices
> ciss0: 1 logical drive
> ciss0: logical drive (b0t0): RAID 1, 34304MB online
> pcib4: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pcib4: domain 0
> pcib4: secondary bus 5
> pcib4: subordinate bus 12
> pcib4: I/O decode 0x5000-0x5fff
> pcib4: memory decode 0xfdf00000-0xfdffffff
> pcib4: no prefetched decode
> pci5: <ACPI PCI bus> on pcib4
> pci5: domain=0, physical bus=5
> found-> vendor=0x8086, dev=0x0329, revid=0x09
> domain=0, bus=5, slot=0, func=0
> class=06-04-00, hdrtype=0x01, mfdev=1
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> powerspec 2 supports D0 D3 current D0
> MSI supports 1 message, 64 bit
> found-> vendor=0x8086, dev=0x032a, revid=0x09
> domain=0, bus=5, slot=0, func=2
> class=06-04-00, hdrtype=0x01, mfdev=1
> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
> powerspec 2 supports D0 D3 current D0
> MSI supports 1 message, 64 bit
> pcib5: <ACPI PCI-PCI bridge> at device 0.0 on pci5
> pcib5: domain 0
> pcib5: secondary bus 6
> pcib5: subordinate bus 9
> pcib5: I/O decode 0x5000-0x5fff
> pcib5: memory decode 0xfdf00000-0xfdffffff
> pcib5: no prefetched decode
> pci6: <ACPI PCI bus> on pcib5
> pci6: domain=0, physical bus=6
> found-> vendor=0x1000, dev=0x0030, revid=0x07
> domain=0, bus=6, slot=1, func=0
> class=01-00-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0157, statreg=0x0230, cachelnsz=16 (dwords)
> lattimer=0x48 (2160 ns), mingnt=0x10 (4000 ns), maxlat=0x06 (1500 ns)
> intpin=a, irq=5
> powerspec 2 supports D0 D1 D2 D3 current D0
> MSI supports 1 message, 64 bit
> map[10]: type I/O Port, range 32, base 0x5000, size 8, enabled
> pcib5: requested I/O range 0x5000-0x50ff: in range
> pcib4: requested I/O range 0x5000-0x50ff: in range
> map[14]: type Memory, range 64, base 0xfdfe0000, size 17, enabled
> pcib5: requested memory range 0xfdfe0000-0xfdffffff: good
> pcib4: requested memory range 0xfdfe0000-0xfdffffff: good
> map[1c]: type Memory, range 64, base 0xfdfc0000, size 17, enabled
> pcib5: requested memory range 0xfdfc0000-0xfdfdffff: good
> pcib4: requested memory range 0xfdfc0000-0xfdfdffff: good
> pcib5: matched entry for 6.1.INTA
> pcib5: slot 1 INTA hardwired to IRQ 74
> found-> vendor=0x103c, dev=0x3220, revid=0x00
> domain=0, bus=6, slot=2, func=0
> class=01-04-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0157, statreg=0x0230, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> powerspec 2 supports D0 D1 D3 current D0
> map[10]: type Memory, range 64, base 0xfdfb0000, size 13, enabled
> pcib5: requested memory range 0xfdfb0000-0xfdfb1fff: good
> pcib4: requested memory range 0xfdfb0000-0xfdfb1fff: good
> map[18]: type I/O Port, range 32, base 0x5400, size 8, enabled
> pcib5: requested I/O range 0x5400-0x54ff: in range
> pcib4: requested I/O range 0x5400-0x54ff: in range
> map[1c]: type Memory, range 64, base 0xfdf40000, size 18, enabled
> pcib5: requested memory range 0xfdf40000-0xfdf7ffff: good
> pcib4: requested memory range 0xfdf40000-0xfdf7ffff: good
> pcib5: matched entry for 6.2.INTA
> pcib5: slot 2 INTA hardwired to IRQ 78
> mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x5000-0x50ff mem 0xfdfe0000-0xfdffffff,0xfdfc0000-0xfdfdffff irq 74 at device 1.0 on pci6
> ioapic3: routing intpin 2 (PCI IRQ 74) to lapic 0 vector 52
> mpt0: [MPSAFE]
> mpt0: [ITHREAD]
> mpt0: MPI Version=1.2.14.0
> mpt0: No Handlers For Any Event Notify Frames. Event 0xa (ACK not required).
> mpt0: No Handlers For Any Event Notify Frames. Event 0xa (ACK not required).
> ciss1: <HP Smart Array P600> port 0x5400-0x54ff mem 0xfdfb0000-0xfdfb1fff,0xfdf40000-0xfdf7ffff irq 78 at device 2.0 on pci6
> ciss1: PERFORMANT Transport
> ciss1: got 0 MSI messages]
> ioapic3: routing intpin 6 (PCI IRQ 78) to lapic 0 vector 53
> ciss1: [MPSAFE]
> ciss1: [ITHREAD]
> ciss1: using 1024 of 1024 available commands
> ciss1: firmware 2.04
> ciss1: 2 SCSI channels
> ciss1: signature 'CISS'
> ciss1: valence 3
> ciss1: supported I/O methods 0x80000006<simple,performant>
> ciss1: active I/O method 0x5<performant>
> ciss1: 4G page base 0x00000000
> ciss1: interrupt coalesce delay 0us
> ciss1: interrupt coalesce count 16
> ciss1: max outstanding commands 1024
> ciss1: bus types 0x200000
> ciss1: server name ''
> ciss1: heartbeat 0x85
> ciss1: 0 physical devices
> ciss1: 0 logical drives
> pcib6: <ACPI PCI-PCI bridge> at device 0.2 on pci5
> pcib6: domain 0
> pcib6: secondary bus 10
> pcib6: subordinate bus 12
> pcib6: I/O decode 0xf000-0xfff
> pcib6: no prefetched decode
> pci10: <ACPI PCI bus> on pcib6
> pci10: domain=0, physical bus=10
> uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x2000-0x201f irq 16 at device 29.0 on pci0
> ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 54
> uhci0: [MPSAFE]
> uhci0: [ITHREAD]
> usbus0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
> uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x2020-0x203f irq 19 at device 29.1 on pci0
> ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 55
> uhci1: [MPSAFE]
> uhci1: [ITHREAD]
> usbus1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
> uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x2040-0x205f irq 18 at device 29.2 on pci0
> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 56
> uhci2: [MPSAFE]
> uhci2: [ITHREAD]
> usbus2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
> uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x2060-0x207f irq 16 at device 29.3 on pci0
> uhci3: [MPSAFE]
> uhci3: [ITHREAD]
> usbus3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
> ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem 0xfbef0000-0xfbef03ff irq 23 at device 29.7 on pci0
> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 57
> ehci0: [MPSAFE]
> ehci0: [ITHREAD]
> usbus4: EHCI version 1.0
> usbus4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
> pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pcib7: domain 0
> pcib7: secondary bus 1
> pcib7: subordinate bus 1
> pcib7: I/O decode 0x1000-0x3fff
> pcib7: memory decode 0xfbf00000-0xfcffffff
> pcib7: no prefetched decode
> pcib7: Subtractively decoded bridge.
> pci1: <ACPI PCI bus> on pcib7
> pci1: domain=0, physical bus=1
> found-> vendor=0x1002, dev=0x4752, revid=0x27
> domain=0, bus=1, slot=3, func=0
> class=03-00-00, hdrtype=0x00, mfdev=0
> cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
> powerspec 2 supports D0 D1 D2 D3 current D0
> map[10]: type Memory, range 32, base 0xfc000000, size 24, enabled
> pcib7: requested memory range 0xfc000000-0xfcffffff: good
> map[14]: type I/O Port, range 32, base 0x3000, size 8, enabled
> pcib7: requested I/O range 0x3000-0x30ff: in range
> map[18]: type Memory, range 32, base 0xfbff0000, size 12, enabled
> pcib7: requested memory range 0xfbff0000-0xfbff0fff: good
> found-> vendor=0x0e11, dev=0xb203, revid=0x01
> domain=0, bus=1, slot=4, func=0
> class=08-80-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords)
> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=a, irq=5
> powerspec 2 supports D0 D3 current D0
> map[10]: type I/O Port, range 32, base 0x1800, size 8, enabled
> pcib7: requested I/O range 0x1800-0x18ff: in range
> map[14]: type Memory, range 32, base 0xfbfe0000, size 9, enabled
> pcib7: requested memory range 0xfbfe0000-0xfbfe01ff: good
> pcib7: matched entry for 1.4.INTA
> pcib7: slot 4 INTA hardwired to IRQ 21
> found-> vendor=0x0e11, dev=0xb204, revid=0x01
> domain=0, bus=1, slot=4, func=2
> class=08-80-00, hdrtype=0x00, mfdev=1
> cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords)
> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> intpin=b, irq=5
> powerspec 2 supports D0 D3 current D0
> map[10]: type I/O Port, range 32, base 0x3400, size 8, enabled
> pcib7: requested I/O range 0x3400-0x34ff: in range
> map[14]: type Memory, range 32, base 0xfbfd0000, size 11, enabled
> pcib7: requested memory range 0xfbfd0000-0xfbfd07ff: good
> map[18]: type Memory, range 32, base 0xfbfc0000, size 13, enabled
> pcib7: requested memory range 0xfbfc0000-0xfbfc1fff: good
> map[1c]: type Memory, range 32, base 0xfbf00000, size 19, enabled
> pcib7: requested memory range 0xfbf00000-0xfbf7ffff: good
> pcib7: matched entry for 1.4.INTB
> pcib7: slot 4 INTB hardwired to IRQ 22
> vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem 0xfc000000-0xfcffffff,0xfbff0000-0xfbff0fff at device 3.0 on pci1
> pci1: <base peripheral> at device 4.0 (no driver attached)
> pci1: <base peripheral> at device 4.2 (no driver attached)
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x500-0x50f at device 31.1 on pci0
> ata0: <ATA channel 0> on atapci0
> ata0: reset tp1 mask=03 ostat0=50 ostat1=00
> ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
> ata0: reset tp2 stat0=00 stat1=00 devices=0x10000
> ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 58
> ata0: [MPSAFE]
> ata0: [ITHREAD]
> ata1: <ATA channel 1> on atapci0
> ata1: reset tp1 mask=03 ostat0=00 ostat1=00
> ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
> ata1: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
> ata1: reset tp2 stat0=01 stat1=01 devices=0x0
> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 59
> ata1: [MPSAFE]
> ata1: [ITHREAD]
> acpi_tz0: <Thermal Zone> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0065
> atkbd: keyboard ID 0x41ab (2)
> kbd0 at atkbd0
> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
> ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 60
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> psm0: unable to allocate IRQ
> psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
> psm0: current command byte:0065
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 61
> psm0: [GIANT-LOCKED]
> psm0: [ITHREAD]
> psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
> psm0: config:00000000, flags:00000008, packet size:3
> psm0: syncmask:c0, syncbits:00
> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 62
> uart0: [FILTER]
> uart0: fast interrupt
> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0
> fdc0: ic_type 90 part_id 73
> ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 63
> fdc0: [FILTER]
> ex_isa_identify()
> pnp_identify: Trying Read_Port at 203
> pnp_identify: Trying Read_Port at 243
> pnp_identify: Trying Read_Port at 283
> pnp_identify: Trying Read_Port at 2c3
> pnp_identify: Trying Read_Port at 303
> pnp_identify: Trying Read_Port at 343
> pnp_identify: Trying Read_Port at 383
> pnp_identify: Trying Read_Port at 3c3
> PNP Identify complete
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> unknown: status reg test failed 0
> unknown: status reg test failed f0
> unknown: status reg test failed ff
> unknown: status reg test failed ff
> ahc_isa_probe 0: ioport 0xc00 alloc failed
> isa_probe_children: disabling PnP devices
> pmtimer0 on isa0
> ata: ata0 already exists; skipping it
> ata: ata1 already exists; skipping it
> atkbdc: atkbdc0 already exists; skipping it
> fdc: fdc0 already exists; skipping it
> sc: sc0 already exists; skipping it
> uart: uart0 already exists; skipping it
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcc7ff,0xcc800-0xd07ff,0xee000-0xeffff pnpid ORM0000 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
> atrtc0: registered as a time-of-day clock (resolution 1000000us)
> ppc0: parallel port not found.
> ppc0: <Parallel port> failed to probe at irq 7 on isa0
> uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> isa_probe_children: probing PnP devices
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> Device configuration finished.
> Reducing kern.maxvnodes 230421 -> 100000
> procfs registered
> lapic: Divisor 2, Frequency 100003947 Hz
> ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 64
> Timecounter "TSC" frequency 3000118380 Hz quality -100
> Timecounters tick every 1.000 msec
> vlan: initialized, using hash tables with chaining
> lo0: bpf attached
> hptrr: no controller detected.
> ata0: Identifying devices: 00010000
> ata0: New devices: 00010000
> usbus0: 12Mbps Full Speed USB v1.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 12Mbps Full Speed USB v1.0
> usbus3: 12Mbps Full Speed USB v1.0
> usbus4: 480Mbps High Speed USB v2.0
> ugen0.1: <Intel> at usbus0
> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
> ugen1.1: <Intel> at usbus1
> uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen2.1: <Intel> at usbus2
> uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
> ugen3.1: <Intel> at usbus3
> uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
> ugen4.1: <Intel> at usbus4
> uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> uhub0: 2 ports with 2 removable, self powered
> uhub1: 2 ports with 2 removable, self powered
> uhub2: 2 ports with 2 removable, self powered
> uhub3: 2 ports with 2 removable, self powered
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> fdc0: output ready timeout
> ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire
> acd0: setting UDMA33
> acd0: <TSSTcorpCD-ROM TS-L162C/N204> CDROM drive at ata0 as master
> acd0: read 4134KB/s (4134KB/s), 96KB buffer, UDMA33
> acd0: Reads: CDR, CDRW, CDDA stream, packet
> acd0: Writes:
> acd0: Audio: play, 255 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> ata1: Identifying devices: 00000000
> ata1: New devices: 00000000
> (noperiph:mpt0:0:-1:-1): reset bus
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> fdc0: output ready timeout
> fdc0: input ready timeout
> uhub4: 8 ports with 8 removable, self powered
> ugen3.2: <vendor 0x192f> at usbus3
> ums0: <vendor 0x192f USB Optical Mouse, class 0/0, rev 2.00/2.00, addr 2> on usbus3
> ums0: 3 buttons and [XYZ] coordinates ID=0
> ugen3.3: <Innovace> at usbus3
> ukbd0: <Innovace HP Wire Keyboard Kit, class 0/0, rev 1.10/2.04, addr 3> on usbus3
> kbd2 at ukbd0
> kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
> uhid0: <Innovace HP Wire Keyboard Kit, class 0/0, rev 1.10/2.04, addr 3> on usbus3
> pass0 at ciss0 bus 0 scbus0 target 0 lun 0
> pass0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-4 device
> pass0: 135.168MB/s transfers
> pass0: Command Queueing enabled
> da0 at ciss0 bus 0 scbus0 target 0 lun 0
> da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-4 device
> da0: 135.168MB/s transfers
> da0: Command Queueing enabled
> da0: 34727MB (71122560 512 byte sectors: 255H 32S/T 8716C)
> GEOM: new disk da0
> ATA PseudoRAID loaded
> SMP: AP CPU #1 Launched!
> cpu1 AP:
> ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
> timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 6 vector 48
> ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 6 vector 49
> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 6 vector 50
> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 6 vector 51
> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 6 vector 52
> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 6 vector 53
> ioapic1: routing intpin 2 (PCI IRQ 26) to lapic 6 vector 54
> ioapic3: routing intpin 2 (PCI IRQ 74) to lapic 6 vector 55
> WARNING: WITNESS option enabled, expect reduced performance.
> Trying to mount root from ufs:/dev/da0s1a
> ct_to_ts([2010-05-06 10:39:27]) = 1273142367.000000000
> start_init: trying /sbin/init
> bge0:
> bge0: link state changed to UP
> link UP
>
>
> And pciconf
>
> hostb0 at pci0:0:0:0: class=0x060000 card=0x32000e11 chip=0x35908086 rev=0x0c hdr=0x00
> vendor = 'Intel Corporation'
> device = 'E7520 Server Memory Controller Hub'
> class = bridge
> subclass = HOST-PCI
> pcib1 at pci0:0:2:0: class=0x060400 card=0x00000000 chip=0x35958086 rev=0x0c hdr=0x01
> vendor = 'Intel Corporation'
> device = 'E752x Memory Controller Hub PCIe Port A0'
> class = bridge
> subclass = PCI-PCI
> pcib4 at pci0:0:6:0: class=0x060400 card=0x00000000 chip=0x35998086 rev=0x0c hdr=0x01
> vendor = 'Intel Corporation'
> device = 'E752x Memory Controller Hub PCIe Port C0'
> class = bridge
> subclass = PCI-PCI
> uhci0 at pci0:0:29:0: class=0x0c0300 card=0x32010e11 chip=0x24d28086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *1'
> class = serial bus
> subclass = USB
> uhci1 at pci0:0:29:1: class=0x0c0300 card=0x32010e11 chip=0x24d48086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *2'
> class = serial bus
> subclass = USB
> uhci2 at pci0:0:29:2: class=0x0c0300 card=0x32010e11 chip=0x24d78086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *3'
> class = serial bus
> subclass = USB
> uhci3 at pci0:0:29:3: class=0x0c0300 card=0x32010e11 chip=0x24de8086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *4'
> class = serial bus
> subclass = USB
> ehci0 at pci0:0:29:7: class=0x0c0320 card=0x32010e11 chip=0x24dd8086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) USB 2.0 EHCI Controller'
> class = serial bus
> subclass = USB
> pcib7 at pci0:0:30:0: class=0x060400 card=0x00000000 chip=0x244e8086 rev=0xc2 hdr=0x01
> vendor = 'Intel Corporation'
> device = '82801 Family (ICH2/3/4/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
> class = bridge
> subclass = PCI-PCI
> isab0 at pci0:0:31:0: class=0x060100 card=0x00000000 chip=0x24d08086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'
> class = bridge
> subclass = PCI-ISA
> atapci0 at pci0:0:31:1: class=0x01018a card=0x32010e11 chip=0x24db8086 rev=0x02 hdr=0x00
> vendor = 'Intel Corporation'
> device = '82801EB/ER (ICH5/ICH5R) EIDE Controller'
> class = mass storage
> subclass = ATA
> pcib2 at pci0:2:0:0: class=0x060400 card=0x00000000 chip=0x03298086 rev=0x09 hdr=0x01
> vendor = 'Intel Corporation'
> device = 'PCI Express-to-PCI Express Bridge A (6700PXH)'
> class = bridge
> subclass = PCI-PCI
> pcib3 at pci0:2:0:2: class=0x060400 card=0x00000000 chip=0x032a8086 rev=0x09 hdr=0x01
> vendor = 'Intel Corporation'
> device = 'PCI Express-to-PCI Express Bridge B (6700PXH)'
> class = bridge
> subclass = PCI-PCI
> bge0 at pci0:3:1:0: class=0x020000 card=0x00d00e11 chip=0x164814e4 rev=0x10 hdr=0x00
> vendor = 'Broadcom Corporation'
> device = 'NetXtreme Dual Gigabit Adapter (BCM5704)'
> class = network
> subclass = ethernet
> bge1 at pci0:3:1:1: class=0x020000 card=0x00d00e11 chip=0x164814e4 rev=0x10 hdr=0x00
> vendor = 'Broadcom Corporation'
> device = 'NetXtreme Dual Gigabit Adapter (BCM5704)'
> class = network
> subclass = ethernet
> ciss0 at pci0:4:3:0: class=0x010400 card=0x40910e11 chip=0x00460e11 rev=0x01 hdr=0x00
> vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
> device = 'Smart Array 6400 Controller (N/A)'
> class = mass storage
> subclass = RAID
> pcib5 at pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x03298086 rev=0x09 hdr=0x01
> vendor = 'Intel Corporation'
> device = 'PCI Express-to-PCI Express Bridge A (6700PXH)'
> class = bridge
> subclass = PCI-PCI
> pcib6 at pci0:5:0:2: class=0x060400 card=0x00000000 chip=0x032a8086 rev=0x09 hdr=0x01
> vendor = 'Intel Corporation'
> device = 'PCI Express-to-PCI Express Bridge B (6700PXH)'
> class = bridge
> subclass = PCI-PCI
> mpt0 at pci0:6:1:0: class=0x010000 card=0x3108103c chip=0x00301000 rev=0x07 hdr=0x00
> vendor = 'LSI Logic (Was: Symbios Logic, NCR)'
> device = 'PCI-X to Ultra320 SCSI Controller (LSI53C1020/1030)'
> class = mass storage
> subclass = SCSI
> ciss1 at pci0:6:2:0: class=0x010400 card=0x3225103c chip=0x3220103c rev=0x00 hdr=0x00
> vendor = 'Hewlett-Packard Company'
> device = 'P600 SmartArray Raid Controller (P600)'
> class = mass storage
> subclass = RAID
> vgapci0 at pci0:1:3:0: class=0x030000 card=0x001e0e11 chip=0x47521002 rev=0x27 hdr=0x00
> vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.'
> device = 'ATI On-Board VGA for HP Proliant 350 G3 (Rage XL PCI)'
> class = display
> subclass = VGA
> none0 at pci0:1:4:0: class=0x088000 card=0xb2060e11 chip=0xb2030e11 rev=0x01 hdr=0x00
> vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
> device = 'Integrated Lights Out Processor (iLo)'
> class = base peripheral
> none1 at pci0:1:4:2: class=0x088000 card=0xb2060e11 chip=0xb2040e11 rev=0x01 hdr=0x00
> vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
> device = 'Integrated Lights Out Processor (iLo)'
> class = base peripheral
>
>
> --
> Regards, Ulf.
Well, that's just odd. This machine doesn't even show that it has the
IBM PCI-X Bridge Chipset. It shows both the LSI and CISS controllers
sitting on the same PCI bus.
the "broken" machine showed an intermediate IBM bus to the PCI-X slot:
pcib6 at pci0:6:2:0: class=0x060400 card=0x00000000 chip=0x01a71014
rev=0x02 hdr=0x01
vendor = 'International Business Machines Corp.'
device = 'PCI-X Bridge R1.1 (IBM 133)'
class = bridge
subclass = PCI-PCI
So I guess these are *not* the same machines?
Sean
More information about the freebsd-scsi
mailing list