kern/146287: [ciss] ciss(4) cannot see more than one SmartArray
controller
Per olof Ljungmark
peo at intersonic.se
Tue May 4 19:21:20 UTC 2010
Scott Long wrote:
> If you can install and boot to the first controller, please run "pciconf -lv" and send me the output. I looks like the linux driver might have a wildcard entry for these controllers, but I want to make sure that I have all of the information before I do something similar for FreeBSD.
>
> Thanks,
> Scott
>
Yes, there is zero problem with the first, the 6i:
pciconf -lv
hostb0 at pci0:0:0:0: class=0x060000 card=0x32000e11 chip=0x35908086
rev=0x0c hdr=0x00
vendor = 'Intel Corporation'
device = 'E7520 Server Memory Controller Hub'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:0:2:0: class=0x060400 card=0x00000000 chip=0x35958086
rev=0x0c hdr=0x01
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub PCIe Port A0'
class = bridge
subclass = PCI-PCI
pcib4 at pci0:0:6:0: class=0x060400 card=0x00000000 chip=0x35998086
rev=0x0c hdr=0x01
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub PCIe Port C0'
class = bridge
subclass = PCI-PCI
uhci0 at pci0:0:29:0: class=0x0c0300 card=0x32010e11 chip=0x24d28086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *1'
class = serial bus
subclass = USB
uhci1 at pci0:0:29:1: class=0x0c0300 card=0x32010e11 chip=0x24d48086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *2'
class = serial bus
subclass = USB
uhci2 at pci0:0:29:2: class=0x0c0300 card=0x32010e11 chip=0x24d78086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *3'
class = serial bus
subclass = USB
uhci3 at pci0:0:29:3: class=0x0c0300 card=0x32010e11 chip=0x24de8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller *4'
class = serial bus
subclass = USB
ehci0 at pci0:0:29:7: class=0x0c0320 card=0x32010e11 chip=0x24dd8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) USB 2.0 EHCI Controller'
class = serial bus
subclass = USB
pcib8 at pci0:0:30:0: class=0x060400 card=0x00000000 chip=0x244e8086
rev=0xc2 hdr=0x01
vendor = 'Intel Corporation'
device = '82801 Family (ICH2/3/4/5/6/7/8/9,63xxESB) Hub
Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0 at pci0:0:31:0: class=0x060100 card=0x00000000 chip=0x24d08086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:0:31:1: class=0x01018a card=0x32010e11 chip=0x24db8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) EIDE Controller'
class = mass storage
subclass = ATA
pcib2 at pci0:2:0:0: class=0x060400 card=0x00000000 chip=0x03298086
rev=0x09 hdr=0x01
vendor = 'Intel Corporation'
device = 'PCI Express-to-PCI Express Bridge A (6700PXH)'
class = bridge
subclass = PCI-PCI
pcib3 at pci0:2:0:2: class=0x060400 card=0x00000000 chip=0x032a8086
rev=0x09 hdr=0x01
vendor = 'Intel Corporation'
device = 'PCI Express-to-PCI Express Bridge B (6700PXH)'
class = bridge
subclass = PCI-PCI
bge0 at pci0:3:1:0: class=0x020000 card=0x00d00e11 chip=0x164814e4
rev=0x10 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme Dual Gigabit Adapter (BCM5704)'
class = network
subclass = ethernet
bge1 at pci0:3:1:1: class=0x020000 card=0x00d00e11 chip=0x164814e4
rev=0x10 hdr=0x00
vendor = 'Broadcom Corporation'
device = 'NetXtreme Dual Gigabit Adapter (BCM5704)'
class = network
subclass = ethernet
ciss0 at pci0:4:3:0: class=0x010400 card=0x40910e11 chip=0x00460e11
rev=0x01 hdr=0x00
vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
device = 'Smart Array 64xx/6i Controller'
class = mass storage
subclass = RAID
pcib5 at pci0:5:0:0: class=0x060400 card=0x00000000 chip=0x03298086
rev=0x09 hdr=0x01
vendor = 'Intel Corporation'
device = 'PCI Express-to-PCI Express Bridge A (6700PXH)'
class = bridge
subclass = PCI-PCI
pcib7 at pci0:5:0:2: class=0x060400 card=0x00000000 chip=0x032a8086
rev=0x09 hdr=0x01
vendor = 'Intel Corporation'
device = 'PCI Express-to-PCI Express Bridge B (6700PXH)'
class = bridge
subclass = PCI-PCI
pcib6 at pci0:6:2:0: class=0x060400 card=0x00000000 chip=0x01a71014
rev=0x02 hdr=0x01
vendor = 'International Business Machines Corp.'
device = 'PCI-X Bridge R1.1 (IBM 133)'
class = bridge
subclass = PCI-PCI
vgapci0 at pci0:1:3:0: class=0x030000 card=0x001e0e11 chip=0x47521002
rev=0x27 hdr=0x00
vendor = 'ATI Technologies Inc. / Advanced Micro Devices, Inc.'
device = 'ATI On-Board VGA for HP Proliant 350 G3 (Rage XL PCI)'
class = display
subclass = VGA
none0 at pci0:1:4:0: class=0x088000 card=0xb2060e11 chip=0xb2030e11
rev=0x01 hdr=0x00
vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
device = 'Integrated Lights Out Processor (iLo)'
class = base peripheral
none1 at pci0:1:4:2: class=0x088000 card=0xb2060e11 chip=0xb2040e11
rev=0x01 hdr=0x00
vendor = 'Compaq Computer Corp (Now owned by Hewlett-Packard)'
device = 'Integrated Lights Out Processor (iLo)'
class = base peripheral
> On May 4, 2010, at 12:00 PM, Per olof Ljungmark wrote:
>
>> The following reply was made to PR kern/146287; it has been noted by GNATS.
>>
>> From: Per olof Ljungmark <peo at intersonic.se>
>> To: bug-followup at FreeBSD.org, peo at intersonic.se
>> Cc: seanbru at yahoo-inc.com
>> Subject: Re: kern/146287: [ciss] ciss(4) cannot see more than one SmartArray
>> controller
>> Date: Tue, 04 May 2010 19:56:19 +0200
>>
>> Copyright (c) 1992-2009 The FreeBSD Project.
>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>> The Regents of the University of California. All rights reserved.
>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>> FreeBSD 8.0-RELEASE-p2 #0: Tue May 4 00:23:37 CEST 2010
>> peo at lowell.i.inter-sonic.com:/usr/obj/usr/src/sys/GENERIC
>> Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80e1a000.
>> Timecounter "i8254" frequency 1193182 Hz quality 0
>> Calibrating TSC clock ... TSC clock: 3400136791 Hz
>> CPU: Intel(R) Xeon(TM) CPU 3.40GHz (3400.14-MHz K8-class CPU)
>> Origin = "GenuineIntel" Id = 0xf41 Stepping = 1
>>
>> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>> Features2=0x649d<SSE3,DTES64,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR>
>> AMD Features=0x20000800<SYSCALL,LM>
>> TSC: P-state invariant
>> real memory = 12884901888 (12288 MB)
>> Physical memory chunk(s):
>> 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
>> 0x0000000000e51000 - 0x00000000dfff2fff, 3743031296 bytes (913826 pages)
>> 0x0000000100000000 - 0x00000003049d6fff, 8667361280 bytes (2116055 pages)
>> avail memory = 12349284352 (11777 MB)
>> ACPI APIC Table: <HP 00000083>
>> INTR: Adding local APIC 6 as a target
>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>> FreeBSD/SMP: 2 package(s) x 1 core(s) x 2 HTT threads
>> cpu0 (BSP): APIC ID: 0
>> cpu1 (AP/HT): APIC ID: 1
>> cpu2 (AP): APIC ID: 6
>> cpu3 (AP/HT): APIC ID: 7
>> APIC: CPU 0 has ACPI ID 0
>> APIC: CPU 1 has ACPI ID 1
>> APIC: CPU 2 has ACPI ID 6
>> APIC: CPU 3 has ACPI ID 7
>> ULE: setup cpu 0
>> ULE: setup cpu 1
>> ULE: setup cpu 2
>> ULE: setup cpu 3
>> ACPI: RSDP 0xf4f00 00024 (v2 HP )
>> ACPI: XSDT 0xdfff3300 0004C (v1 HP P51 00000002 �\^D 0000162E)
>> ACPI: FACP 0xdfff3380 000F4 (v3 HP P51 00000002 �\^D 0000162E)
>> ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16
>> 20090521 tbfadt-707
>> ACPI: DSDT 0xdfff3480 02DAB (v1 HP DSDT 00000001 INTL 20030228)
>> ACPI: FACS 0xdfff3100 00040
>> ACPI: SPCR 0xdfff3140 00050 (v1 HP SPCRRBSU 00000001 �\^D 0000162E)
>> ACPI: MCFG 0xdfff31c0 0003C (v1 HP ProLiant 00000001 00000000)
>> ACPI: APIC 0xdfff3200 000C2 (v1 HP 00000083 00000002 00000000)
>> ACPI: SSDT 0xdfff8000 004C9 (v1 HP SSDTP 00000001 INTL 20030228)
>> MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
>> ioapic0: Routing external 8259A's -> intpin 0
>> MADT: Found IO APIC ID 9, Interrupt 24 at 0xfec80000
>> MADT: Found IO APIC ID 10, Interrupt 48 at 0xfec80400
>> MADT: Found IO APIC ID 11, Interrupt 72 at 0xfec84000
>> MADT: Found IO APIC ID 12, Interrupt 96 at 0xfec84400
>> MADT: Interrupt override: source 0, irq 2
>> ioapic0: Routing IRQ 0 -> intpin 2
>> MADT: Interrupt override: source 9, irq 9
>> ioapic0: intpin 9 trigger: level
>> lapic: Routing NMI -> LINT1
>> lapic: LINT1 trigger: edge
>> lapic: LINT1 polarity: high
>> ioapic0 <Version 2.0> irqs 0-23 on motherboard
>> ioapic1 <Version 2.0> irqs 24-47 on motherboard
>> ioapic2 <Version 2.0> irqs 48-71 on motherboard
>> ioapic3 <Version 2.0> irqs 72-95 on motherboard
>> ioapic4 <Version 2.0> irqs 96-119 on motherboard
>> cpu0 BSP:
>> ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>> timer: 0x000100ef therm: 0x00010000 err: 0x000100f0 pcm: 0x00010400
>> wlan: <802.11 Link Layer>
>> null: <null device, zero device>
>> random: <entropy source, Software, Yarrow>
>> nfslock: pseudo-device
>> kbd: new array size 4
>> kbd1 at kbdmux0
>> mem: <memory>
>> io: <I/O>
>> hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
>> acpi0: <HP P51> on motherboard
>> PCIe: Memory Mapped configuration base @ 0xe0000000
>> ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
>> acpi0: [MPSAFE]
>> acpi0: [ITHREAD]
>> acpi0: Power Button (fixed)
>> acpi0: wakeup code va 0xffffff8000025000 pa 0x4000
>> acpi_bus_number: root bus has no _BBN, assuming 0
>> AcpiOsDerivePciId: \\_SB_.PCI0.CFG0.MEM0 -> bus 0 dev 0 func 0
>> acpi_bus_number: root bus has no _BBN, assuming 0
>> AcpiOsDerivePciId: \\_SB_.PCI0.PTC0.PCXC.SHP0 -> bus 5 dev 0 func 0
>> acpi_bus_number: root bus has no _BBN, assuming 0
>> AcpiOsDerivePciId: \\_SB_.PCI0.IBRG.ICH5 -> bus 0 dev 31 func 0
>> ACPI timer: 0/397 0/5 0/5 0/5 0/6 0/5 0/5 0/6 0/5 0/4 -> 0
>> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
>> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0
>> pci_link0: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 5 N 0 5 7 10 11
>> Validation 0 5 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link1: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 7 N 0 5 7 10 11
>> Validation 0 7 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link2: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 7 N 0 5 7 10 11
>> Validation 0 7 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link3: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 5 N 0 5 7 10 11
>> Validation 0 5 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link4: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 255 N 0 5 7 10 11
>> Validation 0 255 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link5: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 5 N 0 5 7 10 11
>> Validation 0 5 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link6: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 5 N 0 5 7 10 11
>> Validation 0 5 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pci_link7: Index IRQ Rtd Ref IRQs
>> Initial Probe 0 5 N 0 5 7 10 11
>> Validation 0 5 N 0 5 7 10 11
>> After Disable 0 255 N 0 5 7 10 11
>> pcib0: <ACPI Host-PCI bridge> on acpi0
>> pci0: <ACPI PCI bus> on pcib0
>> pci0: domain=0, physical bus=0
>> found-> vendor=0x8086, dev=0x3590, revid=0x0c
>> domain=0, bus=0, slot=0, func=0
>> class=06-00-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0146, statreg=0x0090, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> found-> vendor=0x8086, dev=0x3595, revid=0x0c
>> domain=0, bus=0, slot=2, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=0
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=255
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 2 messages
>> found-> vendor=0x8086, dev=0x3599, revid=0x0c
>> domain=0, bus=0, slot=6, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=0
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=255
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 2 messages
>> found-> vendor=0x8086, dev=0x24d2, revid=0x02
>> domain=0, bus=0, slot=29, func=0
>> class=0c-03-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=5
>> map[20]: type I/O Port, range 32, base 0x3000, size 5, enabled
>> pcib0: matched entry for 0.29.INTA
>> pcib0: slot 29 INTA hardwired to IRQ 16
>> found-> vendor=0x8086, dev=0x24d4, revid=0x02
>> domain=0, bus=0, slot=29, func=1
>> class=0c-03-00, hdrtype=0x00, mfdev=0
>> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=b, irq=5
>> map[20]: type I/O Port, range 32, base 0x3020, size 5, enabled
>> pcib0: matched entry for 0.29.INTB
>> pcib0: slot 29 INTB hardwired to IRQ 19
>> found-> vendor=0x8086, dev=0x24d7, revid=0x02
>> domain=0, bus=0, slot=29, func=2
>> class=0c-03-00, hdrtype=0x00, mfdev=0
>> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=c, irq=7
>> map[20]: type I/O Port, range 32, base 0x3040, size 5, enabled
>> pcib0: matched entry for 0.29.INTC
>> pcib0: slot 29 INTC hardwired to IRQ 18
>> found-> vendor=0x8086, dev=0x24de, revid=0x02
>> domain=0, bus=0, slot=29, func=3
>> class=0c-03-00, hdrtype=0x00, mfdev=0
>> cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=5
>> map[20]: type I/O Port, range 32, base 0x3060, size 5, enabled
>> pcib0: matched entry for 0.29.INTA
>> pcib0: slot 29 INTA hardwired to IRQ 16
>> found-> vendor=0x8086, dev=0x24dd, revid=0x02
>> domain=0, bus=0, slot=29, func=7
>> class=0c-03-20, hdrtype=0x00, mfdev=0
>> cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=d, irq=5
>> powerspec 2 supports D0 D3 current D0
>> map[10]: type Memory, range 32, base 0xfbef0000, size 10, enabled
>> pcib0: matched entry for 0.29.INTD
>> pcib0: slot 29 INTD hardwired to IRQ 23
>> found-> vendor=0x8086, dev=0x244e, revid=0xc2
>> domain=0, bus=0, slot=30, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=0
>> cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> found-> vendor=0x8086, dev=0x24d0, revid=0x02
>> domain=0, bus=0, slot=31, func=0
>> class=06-01-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x014f, statreg=0x0280, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> found-> vendor=0x8086, dev=0x24db, revid=0x02
>> domain=0, bus=0, slot=31, func=1
>> class=01-01-8a, hdrtype=0x00, mfdev=0
>> cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=255
>> map[20]: type I/O Port, range 32, base 0x500, size 4, enabled
>> map[24]: type Memory, range 32, base 0, size 10, memory disabled
>> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
>> pcib1: domain 0
>> pcib1: secondary bus 2
>> pcib1: subordinate bus 4
>> pcib1: I/O decode 0x4000-0x4fff
>> pcib1: memory decode 0xfdd00000-0xfdefffff
>> pcib1: no prefetched decode
>> pci2: <ACPI PCI bus> on pcib1
>> pci2: domain=0, physical bus=2
>> found-> vendor=0x8086, dev=0x0329, revid=0x09
>> domain=0, bus=2, slot=0, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=1
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 1 message, 64 bit
>> found-> vendor=0x8086, dev=0x032a, revid=0x09
>> domain=0, bus=2, slot=0, func=2
>> class=06-04-00, hdrtype=0x01, mfdev=1
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 1 message, 64 bit
>> pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci2
>> pcib2: domain 0
>> pcib2: secondary bus 3
>> pcib2: subordinate bus 3
>> pcib2: I/O decode 0xf000-0xfff
>> pcib2: memory decode 0xfdd00000-0xfddfffff
>> pcib2: no prefetched decode
>> pci3: <ACPI PCI bus> on pcib2
>> pci3: domain=0, physical bus=3
>> found-> vendor=0x14e4, dev=0x1648, revid=0x10
>> domain=0, bus=3, slot=1, func=0
>> class=02-00-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=7
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 8 messages, 64 bit
>> map[10]: type Memory, range 64, base 0xfddf0000, size 16, enabled
>> pcib2: requested memory range 0xfddf0000-0xfddfffff: good
>> pcib1: requested memory range 0xfddf0000-0xfddfffff: good
>> pcib2: matched entry for 3.1.INTA
>> pcib2: slot 1 INTA hardwired to IRQ 25
>> found-> vendor=0x14e4, dev=0x1648, revid=0x10
>> domain=0, bus=3, slot=1, func=1
>> class=02-00-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
>> intpin=b, irq=7
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 8 messages, 64 bit
>> map[10]: type Memory, range 64, base 0xfdde0000, size 16, enabled
>> pcib2: requested memory range 0xfdde0000-0xfddeffff: good
>> pcib1: requested memory range 0xfdde0000-0xfddeffff: good
>> pcib2: matched entry for 3.1.INTB
>> pcib2: slot 1 INTB hardwired to IRQ 26
>> pci0:3:1:0: bad VPD cksum, remain 19
>> bge0: <HP NC7782 Gigabit Server Adapter, ASIC rev. 0x2100> mem
>> 0xfddf0000-0xfddfffff irq 25 at device 1.0 on pci3
>> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfddf0000
>> bge0: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
>> miibus0: <MII bus> on bge0
>> brgphy0: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus0
>> brgphy0: OUI 0x000818, model 0x0019, rev. 0
>> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> bge0: bpf attached
>> bge0: Ethernet address: 00:12:79:d1:2e:2d
>> ioapic1: routing intpin 1 (PCI IRQ 25) to lapic 0 vector 49
>> bge0: [MPSAFE]
>> bge0: [ITHREAD]
>> pci0:3:1:1: bad VPD cksum, remain 19
>> bge1: <HP NC7782 Gigabit Server Adapter, ASIC rev. 0x2100> mem
>> 0xfdde0000-0xfddeffff irq 26 at device 1.1 on pci3
>> bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfdde0000
>> bge1: CHIP ID 0x21000000; ASIC REV 0x02; CHIP REV 0x21; PCI-X
>> miibus1: <MII bus> on bge1
>> brgphy1: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus1
>> brgphy1: OUI 0x000818, model 0x0019, rev. 0
>> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> bge1: bpf attached
>> bge1: Ethernet address: 00:12:79:d1:2e:2c
>> ioapic1: routing intpin 2 (PCI IRQ 26) to lapic 0 vector 50
>> bge1: [MPSAFE]
>> bge1: [ITHREAD]
>> pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci2
>> pcib3: domain 0
>> pcib3: secondary bus 4
>> pcib3: subordinate bus 4
>> pcib3: I/O decode 0x4000-0x4fff
>> pcib3: memory decode 0xfde00000-0xfdefffff
>> pcib3: no prefetched decode
>> pci4: <ACPI PCI bus> on pcib3
>> pci4: domain=0, physical bus=4
>> found-> vendor=0x0e11, dev=0x0046, revid=0x01
>> domain=0, bus=4, slot=3, func=0
>> class=01-04-00, hdrtype=0x00, mfdev=0
>> cmdreg=0x0157, statreg=0x0230, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=5
>> powerspec 2 supports D0 D1 D3 current D0
>> map[10]: type Memory, range 64, base 0xfdef0000, size 13, enabled
>> pcib3: requested memory range 0xfdef0000-0xfdef1fff: good
>> pcib1: requested memory range 0xfdef0000-0xfdef1fff: good
>> map[18]: type I/O Port, range 32, base 0x4000, size 8, enabled
>> pcib3: requested I/O range 0x4000-0x40ff: in range
>> pcib1: requested I/O range 0x4000-0x40ff: in range
>> map[1c]: type Memory, range 64, base 0xfde80000, size 18, enabled
>> pcib3: requested memory range 0xfde80000-0xfdebffff: good
>> pcib1: requested memory range 0xfde80000-0xfdebffff: good
>> pcib3: matched entry for 4.3.INTA
>> pcib3: slot 3 INTA hardwired to IRQ 51
>> ciss0: <HP Smart Array 6i> port 0x4000-0x40ff mem
>> 0xfdef0000-0xfdef1fff,0xfde80000-0xfdebffff irq 51 at device 3.0 on pci4
>> ciss0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xfdef0000
>> ciss0: PERFORMANT Transport
>> ciss0: got 0 MSI messages]
>> ioapic2: routing intpin 3 (PCI IRQ 51) to lapic 0 vector 51
>> ciss0: [MPSAFE]
>> ciss0: [ITHREAD]
>> ciss0: using 256 of 1024 available commands
>> ciss0: firmware 2.84
>> ciss0: 2 SCSI channels
>> ciss0: signature 'CISS'
>> ciss0: valence 1
>> ciss0: supported I/O methods 0x80000006<simple,performant>
>> ciss0: active I/O method 0x5<performant>
>> ciss0: 4G page base 0x00000000
>> ciss0: interrupt coalesce delay 0us
>> ciss0: interrupt coalesce count 16
>> ciss0: max outstanding commands 1024
>> ciss0: bus types 0x4
>> ciss0: server name ''
>> ciss0: heartbeat 0x5c
>> ciss0: 6 physical devices
>> ciss0: 1 logical drive
>> ciss0: logical drive (b0t0): RAID 1, 139776MB online
>> pcib4: <ACPI PCI-PCI bridge> at device 6.0 on pci0
>> pcib4: domain 0
>> pcib4: secondary bus 5
>> pcib4: subordinate bus 12
>> pcib4: I/O decode 0x5000-0x5fff
>> pcib4: memory decode 0xfdf00000-0xfdffffff
>> pcib4: no prefetched decode
>> pci5: <ACPI PCI bus> on pcib4
>> pci5: domain=0, physical bus=5
>> found-> vendor=0x8086, dev=0x0329, revid=0x09
>> domain=0, bus=5, slot=0, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=1
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 1 message, 64 bit
>> found-> vendor=0x8086, dev=0x032a, revid=0x09
>> domain=0, bus=5, slot=0, func=2
>> class=06-04-00, hdrtype=0x01, mfdev=1
>> cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D3 current D0
>> MSI supports 1 message, 64 bit
>> pcib5: <ACPI PCI-PCI bridge> at device 0.0 on pci5
>> pcib5: domain 0
>> pcib5: secondary bus 6
>> pcib5: subordinate bus 9
>> pcib5: I/O decode 0x5000-0x5fff
>> pcib5: memory decode 0xfdf00000-0xfdffffff
>> pcib5: no prefetched decode
>> pci6: <ACPI PCI bus> on pcib5
>> pci6: domain=0, physical bus=6
>> found-> vendor=0x1014, dev=0x01a7, revid=0x02
>> domain=0, bus=6, slot=2, func=0
>> class=06-04-00, hdrtype=0x01, mfdev=0
>> cmdreg=0x0147, statreg=0x0230, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D3 current D0
>> pcib6: <ACPI PCI-PCI bridge> at device 2.0 on pci6
>> pcib6: domain 0
>> pcib6: secondary bus 7
>> pcib6: subordinate bus 7
>> pcib6: I/O decode 0x5000-0x5fff
>> pcib6: memory decode 0xfdf00000-0xfdffffff
>> pcib6: no prefetched decode
>> device_attach: pcib6 attach returned 6
>> pcib7: <ACPI PCI-PCI bridge> at device 0.2 on pci5
>> pcib7: domain 0
>> pcib7: secondary bus 10
>> pcib7: subordinate bus 12
>> pcib7: I/O decode 0xf000-0xfff
>> pcib7: no prefetched decode
>> pci10: <ACPI PCI bus> on pcib7
>> pci10: domain=0, physical bus=10
>> uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x3000-0x301f
>> irq 16 at device 29.0 on pci0
>> uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x3000
>> ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 52
>> uhci0: [MPSAFE]
>> uhci0: [ITHREAD]
>> uhci0: LegSup = 0x003b
>> usbus0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
>> uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x3020-0x303f
>> irq 19 at device 29.1 on pci0
>> uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x3020
>> ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 53
>> uhci1: [MPSAFE]
>> uhci1: [ITHREAD]
>> uhci1: LegSup = 0x0010
>> usbus1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
>> uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x3040-0x305f
>> irq 18 at device 29.2 on pci0
>> uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x3040
>> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 54
>> uhci2: [MPSAFE]
>> uhci2: [ITHREAD]
>> uhci2: LegSup = 0x0010
>> usbus2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
>> uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x3060-0x307f
>> irq 16 at device 29.3 on pci0
>> uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x3060
>> uhci3: [MPSAFE]
>> uhci3: [ITHREAD]
>> uhci3: LegSup = 0x0010
>> usbus3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
>> ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem
>> 0xfbef0000-0xfbef03ff irq 23 at device 29.7 on pci0
>> ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfbef0000
>> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 55
>> ehci0: [MPSAFE]
>> ehci0: [ITHREAD]
>> usbus4: EHCI version 1.0
>> usbus4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
>> pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
>> pcib8: domain 0
>> pcib8: secondary bus 1
>> pcib8: subordinate bus 1
>> pcib8: I/O decode 0x1000-0x2fff
>> pcib8: memory decode 0xfbf00000-0xfcffffff
>> pcib8: no prefetched decode
>> pcib8: Subtractively decoded bridge.
>> pci1: <ACPI PCI bus> on pcib8
>> pci1: domain=0, physical bus=1
>> found-> vendor=0x1002, dev=0x4752, revid=0x27
>> domain=0, bus=1, slot=3, func=0
>> class=03-00-00, hdrtype=0x00, mfdev=0
>> cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
>> powerspec 2 supports D0 D1 D2 D3 current D0
>> map[10]: type Memory, range 32, base 0xfc000000, size 24, enabled
>> pcib8: requested memory range 0xfc000000-0xfcffffff: good
>> map[14]: type I/O Port, range 32, base 0x2000, size 8, enabled
>> pcib8: requested I/O range 0x2000-0x20ff: in range
>> map[18]: type Memory, range 32, base 0xfbff0000, size 12, enabled
>> pcib8: requested memory range 0xfbff0000-0xfbff0fff: good
>> found-> vendor=0x0e11, dev=0xb203, revid=0x01
>> domain=0, bus=1, slot=4, func=0
>> class=08-80-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords)
>> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=a, irq=5
>> powerspec 2 supports D0 D3 current D0
>> map[10]: type I/O Port, range 32, base 0x1800, size 8, enabled
>> pcib8: requested I/O range 0x1800-0x18ff: in range
>> map[14]: type Memory, range 32, base 0xfbfe0000, size 9, enabled
>> pcib8: requested memory range 0xfbfe0000-0xfbfe01ff: good
>> pcib8: matched entry for 1.4.INTA
>> pcib8: slot 4 INTA hardwired to IRQ 21
>> found-> vendor=0x0e11, dev=0xb204, revid=0x01
>> domain=0, bus=1, slot=4, func=2
>> class=08-80-00, hdrtype=0x00, mfdev=1
>> cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords)
>> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>> intpin=b, irq=5
>> powerspec 2 supports D0 D3 current D0
>> map[10]: type I/O Port, range 32, base 0x2400, size 8, enabled
>> pcib8: requested I/O range 0x2400-0x24ff: in range
>> map[14]: type Memory, range 32, base 0xfbfd0000, size 11, enabled
>> pcib8: requested memory range 0xfbfd0000-0xfbfd07ff: good
>> map[18]: type Memory, range 32, base 0xfbfc0000, size 13, enabled
>> pcib8: requested memory range 0xfbfc0000-0xfbfc1fff: good
>> map[1c]: type Memory, range 32, base 0xfbf00000, size 19, enabled
>> pcib8: requested memory range 0xfbf00000-0xfbf7ffff: good
>> pcib8: matched entry for 1.4.INTB
>> pcib8: slot 4 INTB hardwired to IRQ 22
>> vgapci0: <VGA-compatible display> port 0x2000-0x20ff mem
>> 0xfc000000-0xfcffffff,0xfbff0000-0xfbff0fff at device 3.0 on pci1
>> pci1: <base peripheral> at device 4.0 (no driver attached)
>> pci1: <base peripheral> at device 4.2 (no driver attached)
>> isab0: <PCI-ISA bridge> at device 31.0 on pci0
>> isa0: <ISA bus> on isab0
>> atapci0: <Intel ICH5 UDMA100 controller> port
>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x500-0x50f at device 31.1 on pci0
>> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x500
>> ata0: <ATA channel 0> on atapci0
>> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
>> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
>> ata0: reset tp1 mask=03 ostat0=50 ostat1=00
>> ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
>> ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
>> ata0: reset tp2 stat0=00 stat1=00 devices=0x10000
>> ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 56
>> ata0: [MPSAFE]
>> ata0: [ITHREAD]
>> ata1: <ATA channel 1> on atapci0
>> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
>> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
>> ata1: reset tp1 mask=03 ostat0=00 ostat1=00
>> ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
>> ata1: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
>> ata1: reset tp2 stat0=01 stat1=01 devices=0x0
>> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 57
>> ata1: [MPSAFE]
>> ata1: [ITHREAD]
>> acpi_tz0: <Thermal Zone> on acpi0
>> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
>> atkbd0: <AT Keyboard> irq 1 on atkbdc0
>> atkbd: the current kbd controller command byte 0065
>> atkbd: keyboard ID 0x41ab (2)
>> kbd0 at atkbd0
>> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
>> ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 58
>> atkbd0: [GIANT-LOCKED]
>> atkbd0: [ITHREAD]
>> psm0: unable to allocate IRQ
>> psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
>> psm0: current command byte:0065
>> psm0: <PS/2 Mouse> irq 12 on atkbdc0
>> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 59
>> psm0: [GIANT-LOCKED]
>> psm0: [ITHREAD]
>> psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
>> psm0: config:00000000, flags:00000008, packet size:3
>> psm0: syncmask:c0, syncbits:00
>> uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
>> ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 60
>> uart0: [FILTER]
>> uart0: fast interrupt
>> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0
>> fdc0: ic_type 90 part_id 73
>> ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 0 vector 61
>> fdc0: [FILTER]
>> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
>> cpu0: <ACPI CPU> on acpi0
>> ACPI: SSDT 0xdfff9000 002DA (v1 HP SSDT0 00000001 INTL 20030228)
>> cpu0: switching to generic Cx mode
>> acpi_perf0: <ACPI CPU Frequency Control> on cpu0
>> p4tcc0: <CPU Frequency Thermal Control> on cpu0
>> cpu1: <ACPI CPU> on acpi0
>> ACPI: SSDT 0xdfff9300 002DA (v1 HP SSDT1 00000001 INTL 20030228)
>> est1: <Enhanced SpeedStep Frequency Control> on cpu1
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 112d0000112d
>> device_attach: est1 attach returned 6
>> p4tcc1: <CPU Frequency Thermal Control> on cpu1
>> cpu2: <ACPI CPU> on acpi0
>> ACPI: SSDT 0xdfff9600 002DA (v1 HP SSDT2 00000001 INTL 20030228)
>> est2: <Enhanced SpeedStep Frequency Control> on cpu2
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 112d0000112d
>> device_attach: est2 attach returned 6
>> p4tcc2: <CPU Frequency Thermal Control> on cpu2
>> cpu3: <ACPI CPU> on acpi0
>> ACPI: SSDT 0xdfff9900 002DF (v1 HP SSDT3 00000001 INTL 20030228)
>> est3: <Enhanced SpeedStep Frequency Control> on cpu3
>> est: CPU supports Enhanced Speedstep, but is not recognized.
>> est: cpu_vendor GenuineIntel, msr 112d0000112d
>> device_attach: est3 attach returned 6
>> p4tcc3: <CPU Frequency Thermal Control> on cpu3
>> ahc_isa_probe 0: ioport 0xc00 alloc failed
>> ex_isa_identify()
>> isa_probe_children: disabling PnP devices
>> atkbdc: atkbdc0 already exists; skipping it
>> fdc: fdc0 already exists; skipping it
>> sc: sc0 already exists; skipping it
>> uart: uart0 already exists; skipping it
>> isa_probe_children: probing non-PnP devices
>> orm0: <ISA Option ROMs> at iomem
>> 0xc0000-0xc7fff,0xc8000-0xcbfff,0xee000-0xeffff on isa0
>> sc0: <System console> at flags 0x100 on isa0
>> sc0: VGA <16 virtual consoles, flags=0x300>
>> sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>> atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
>> atrtc0: registered as a time-of-day clock (resolution 1000000us)
>> ppc0: cannot reserve I/O port range
>> ppc0: <Parallel port> failed to probe at irq 7 on isa0
>> uart1: <Non-standard ns8250 class UART with FIFOs> at port 0x2f8-0x2ff
>> irq 3 on isa0
>> ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 62
>> uart1: [FILTER]
>> uart1: fast interrupt
>> isa_probe_children: probing PnP devices
>> Device configuration finished.
>> Reducing kern.maxvnodes 763673 -> 100000
>> procfs registered
>> lapic: Divisor 2, Frequency 100004020 hz
>> Timecounter "TSC" frequency 3400136791 Hz quality -100
>> Timecounters tick every 1.000 msec
>> lo0: bpf attached
>> hptrr: no controller detected.
>> ata0: Identifying devices: 00010000
>> ata0: New devices: 00010000
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> fdc0: output ready timeout
>> usbus0: 12Mbps Full Speed USB v1.0
>> usbus1: 12Mbps Full Speed USB v1.0
>> usbus2: 12Mbps Full Speed USB v1.0
>> usbus3: 12Mbps Full Speed USB v1.0
>> usbus4: 480Mbps High Speed USB v2.0
>> ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
>> acd0: setting PIO4 on ICH5 chip
>> acd0: setting UDMA33 on ICH5 chip
>> ugen0.1: <Intel> at usbus0
>> uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
>> ugen1.1: <Intel> at usbus1
>> uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
>> ugen2.1: <Intel> at usbus2
>> uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
>> ugen3.1: <Intel> at usbus3
>> uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
>> ugen4.1: <Intel> at usbus4
>> uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
>> acd0: <HL-DT-STCD-RW/DVD DRIVE GCC-C10N/2.00> CDRW drive at ata0 as master
>> acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer,
>> UDMA33
>> acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
>> acd0: Writes: CDR, CDRW, test write, burnproof
>> acd0: Audio: play, 256 volume levels
>> acd0: Mechanism: ejectable tray, unlocked
>> acd0: Medium: no/blank disc
>> ata1: Identifying devices: 00000000
>> ata1: New devices: 00000000
>> uhub0: 2 ports with 2 removable, self powered
>> uhub1: 2 ports with 2 removable, self powered
>> uhub2: 2 ports with 2 removable, self powered
>> uhub3: 2 ports with 2 removable, self powered
>> fdc0: output ready timeout
>> fdc0: input ready timeout
>> fdc0: input ready timeout
>> fdc0: output ready timeout
>> fdc0: input ready timeout
>> fdc0: input ready timeout
>> fdc0: output ready timeout
>> fdc0: input ready timeout
>> fdc0: input ready timeout
>> fdc0: output ready timeout
>> fdc0: input ready timeout
>> fdc0: input ready timeout
>> da0 at ciss0 bus 0 target 0 lun 0
>> da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-4 device
>> da0: 135.168MB/s transfers
>> da0: Command Queueing enabled
>> da0: 140002MB (286726080 512 byte sectors: 255H 32S/T 35138C)
>> pass0 at ciss0 bus 0 target 0 lun 0
>> pass0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-4 device
>> pass0: 135.168MB/s transfers
>> pass0: Command Queueing enabled
>> pass1 at ciss0 bus 33 target 0 lun 0
>> pass1: <SEAGATE ST373207LC 0005> Fixed Uninstalled SCSI-3 device
>> pass1: Serial Number 3KT5ABMQ000077052PVP
>> pass1: 135.168MB/s transfers
>> pass1: Command Queueing enabled
>> pass2 at ciss0 bus 33 target 1 lun 0
>> pass2: <SEAGATE ST373207LC 0005> Fixed Uninstalled SCSI-3 device
>> pass2: Serial Number 3KT65G0300009740UG3C
>> pass2: 135.168MB/s transfers
>> pass2: Command Queueing enabled
>> pass3 at ciss0 bus 33 target 2 lun 0
>> pass3: <SEAGATE ST373207LC 0005> Fixed Uninstalled SCSI-3 device
>> pass3: Serial Number 3KT65G7800009740W27L
>> pass3: 135.168MB/s transfers
>> pass3: Command Queueing enabled
>> pass4 at ciss0 bus 33 target 3 lun 0
>> pass4: <SEAGATE ST373207LC 0003> Fixed Uninstalled SCSI-3 device
>> pass4: Serial Number 3KT2W9ZB00007616NLEN
>> pass4: 135.168MB/s transfers
>> pass4: Command Queueing enabled
>> pass5 at ciss0 bus 33 target 4 lun 0
>> pass5: <SEAGATE ST373207LC 0003> Fixed Uninstalled SCSI-3 device
>> pass5: Serial Number 3KT18LBP0000754281N7
>> pass5: 135.168MB/s transfers
>> pass5: Command Queueing enabled
>> pass6 at ciss0 bus 33 target 7 lun 0
>> pass6: <COMPAQ PROLIANT 6L6I 0.10> Fixed Processor SCSI-2 device
>> pass6: 135.168MB/s transfers
>> ATA PseudoRAID loaded
>> SMP: AP CPU #1 Launched!
>> cpu1 AP:
>> ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
>> SMP: AP CPU #2 Launched!
>> cpu2 AP:
>> ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
>> SMP: AP CPU #3 Launched!
>> cpu3 AP:
>> ID: 0x07000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
>> timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
>> ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 6 vector 48
>> ioapic0: routing intpin 6 (ISA IRQ 6) to lapic 6 vector 49
>> ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 6 vector 50
>> ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 6 vector 51
>> ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 6 vector 52
>> ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 6 vector 53
>> ioapic1: routing intpin 2 (PCI IRQ 26) to lapic 6 vector 54
>> uhub4: 8 ports with 8 removable, self powered
>> ugen2.2: <vendor 0x04d9> at usbus2
>> ukbd0: <vendor 0x04d9 product 0x1400, class 0/0, rev 1.10/1.43, addr 2>
>> on usbus2
>> kbd2 at ukbd0
>> kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
>> ums0: <vendor 0x04d9 product 0x1400, class 0/0, rev 1.10/1.43, addr 2>
>> on usbus2
>> ums0: 5 buttons and [XYZ] coordinates ID=1
>> GEOM: new disk da0
>> Trying to mount root from ufs:/dev/da0s1a
>> ct_to_ts([2010-05-04 17:49:30]) = 1272995370.000000000
>> start_init: trying /sbin/init
>> bge0:
>> bge0: link state changed to UP
>> link UP
>>
>> _______________________________________________
>> freebsd-scsi at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-scsi
>> To unsubscribe, send any mail to "freebsd-scsi-unsubscribe at freebsd.org"
>
More information about the freebsd-scsi
mailing list