isp and scsi_target
Matthew Jacob
mj at feral.com
Wed Apr 21 02:16:32 UTC 2010
What a mess.
I need to look at this in detail. The stuff was working (sort of) in
RELENG_8, but got very little testing otherwise.
> We're trying to get an emulated disk to show up on 7.3-REL and not
> having much luck. This is a point-to-point connection with a pair of
> Qlogic cards (pciconf below). There is no FC switch in between the
> machines, and both cards were defaulted prior to testing (factory BIOS
> settings). The moment I rescan the bus on the initiator, the target
> machine panics and dumps core. The initiator hangs until the FC card
> on the initiator resets, then returns to the prompt (wedge??).
>
> Here's the card (same in both machines though different scsi bus)
>
> isp0 at pci0:5:1:0: class=0x0c0400 card=0x00091077 chip=0x23001077
> rev=0x01 hdr=0x00
> vendor = 'QLogic Corporation'
> device = 'QLA2300 SANblade 2300 64-bit FC-AL Adapter'
> class = serial bus
> subclass = Fibre Channel
>
>
> I get tons of debugging output on the target machine when launching
> scsi_target with the following command:
>
> test001# scsi_target -d 3:0:0 /usr/home/testuser/target0
>
> Here's a snip-it of the debugging output on the target machine after
> the above command (goes on for pages):
>
> scsi_target: sending ccb (0x332)
> scsi_target: sending ccb (0x334)
> scsi_target: sending ccb (0x332)
> scsi_target: sending ccb (0x334)
> scsi_target: main loop beginning
>
> Then this when the initiator rescans the bus just before it tanks:
>
> scsi_target: read ready
> scsi_target: event -1 done
> scsi_target: Working on ATIO 0x2825c200
> scsi_target: tcmd_handle atio 0x2825c200 ctio 0x2825e0c0 atioflags 0x8000
>
> And this in the log on the initiator when it comes back up:
>
> isp0: bad pdb (110) @ handle 0x1
> isp0: 0: hdl 0x1 PROB al1 tgt 0 TGT 0x0000e8 => UNK 0x000000; WWNN
> 0x200000e08b08f56d WWPN 0x210000e08b08f56d
>
>
> Here's the relevant kernel info on the target:
>
> # ISP SCSI Controllers
> device isp # Qlogic family
> device ispfw # Firmware for QLogic HBAs
> options ISP_TARGET_MODE # Qlogic family target mode
> device targ
> device targbh
> options CAMDEBUG
> options VFS_AIO
>
> /boot/device.hints on the target:
>
> hint.isp.0.fullduplex="1"
> hint.isp.0.topology="nport-only"
> hint.isp.0.role="target"
>
> Here's the relevant kernel info on the initiator:
>
> # ISP SCSI Controllers
> device isp # Qlogic family
> device ispfw # Firmware for QLogic HBAs
> device targ
> device targbh
> options CAMDEBUG
> options VFS_AIO
>
> /boot/device.hints on the initiator:
>
> hint.isp.0.fullduplex="1"
> hint.isp.0.topology="nport-only"
> hint.isp.0.role="initiator"
> hint.isp.0.iid="4"
>
>
> I'm seeing this in the syslog on the initiator:
>
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.5 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.5 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.5 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.7 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.7 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.7 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.7 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.6 (count 36,
> resid 36, status not marked)
> Apr 20 22:21:28 test002 kernel: isp0: bad underrun for 0.7 (count 36,
> resid 36, status not marked)
>
>
> Here's the bt for the core dump after the panic which looks to be
> pretty useless from my observation (I'd _love_ to be wrong!!):
>
> test001# kgdb kernel.debug /var/crash/vmcore.0
>
> Unread portion of the kernel message buffer:
> (targ0:isp0:0:0:0): targdone 0xc7b7b400
> (targ0:isp0:0:0:0): targread
> (targ0:isp0:0:0:0): targread ccb 0xc7b7b400 (0x2825c200)
> (targ0:isp0:0:0:0): targreturnccb 0xc7b7b400
> cam_debug: targfreeccb descr 0xc7b80060 and
> cam_debug: freeing ccb 0xc7b7b400
> (targ0:isp0:0:0:0): write - uio_resid 4
> (targ0:isp0:0:0:0): Sending queued ccb 0x933 (0x2825e0c0)
> (targ0:isp0:0:0:0): targstart 0xc73bd400
> (targ0:isp0:0:0:0): sendccb 0xc73bd400
>
>
> Fatal trap 12: page fault while in kernel mode
> cpuid = 4; apic id = 04
> fault virtual address = 0x4
> fault code = supervisor read, page not present
> instruction pointer = 0x20:0xc04f0a66
> stack pointer = 0x28:0xc6fe5900
> frame pointer = 0x28:0xc6fe5950
> code segment = base 0x0, limit 0xfffff, type 0x1b
> = DPL 0, pres 1, def32 1, gran 1
> processor eflags = interrupt enabled, resume, IOPL = 0
> current process = 639 (scsi_target)
> trap number = 12
> panic: page fault
> cpuid = 4
> Uptime: 51s
> Physical memory: 3767 MB
> Dumping 102 MB: 87 71 55 39 23 7
>
> Reading symbols from /boot/kernel/ispfw.ko...Reading symbols from
> /boot/kernel/ispfw.ko.symbols...done.
> done.
> Loaded symbols for /boot/kernel/ispfw.ko
> Reading symbols from /boot/kernel/acpi.ko...Reading symbols from
> /boot/kernel/acpi.ko.symbols...done.
> done.
> Loaded symbols for /boot/kernel/acpi.ko
> #0 doadump () at pcpu.h:196
> 196 __asm __volatile("movl %%fs:0,%0" : "=r" (td));
> (kgdb) bt
> #0 doadump () at pcpu.h:196
> #1 0xc05c4e87 in boot (howto=260) at
> /usr/src/sys/kern/kern_shutdown.c:418
> #2 0xc05c5159 in panic (fmt=Variable "fmt" is not available.
> ) at /usr/src/sys/kern/kern_shutdown.c:574
> #3 0xc08258bc in trap_fatal (frame=0xc6fe58c0, eva=4) at
> /usr/src/sys/i386/i386/trap.c:950
> #4 0xc0825b20 in trap_pfault (frame=0xc6fe58c0, usermode=0, eva=4) at
> /usr/src/sys/i386/i386/trap.c:863
> #5 0xc08264d9 in trap (frame=0xc6fe58c0) at
> /usr/src/sys/i386/i386/trap.c:541
> #6 0xc080a1db in calltrap () at /usr/src/sys/i386/i386/exception.s:166
> #7 0xc04f0a66 in isp_pci_dmasetup (isp=0xc71de000, csio=0xc73bd400,
> rq=0xc6fe59c4, nxtip=0xc6fe5a0c, optr=1) at
> /usr/src/sys/dev/isp/isp_pci.c:2781
> #8 0xc04e96a1 in isp_action (sim=0xc7198e00, ccb=0xc73bd400) at
> /usr/src/sys/dev/isp/isp_freebsd.c:1373
> #9 0xc0449104 in xpt_run_dev_sendq (bus=0xc71d65c0) at
> /usr/src/sys/cam/cam_xpt.c:3894
> #10 0xc04495ce in xpt_action (start_ccb=0xc73bd400) at
> /usr/src/sys/cam/cam_xpt.c:3056
> #11 0xc0466ee6 in targsendccb (softc=0xc744ee00, ccb=0xc73bd400,
> descr=0xc7b80020) at /usr/src/sys/cam/scsi/scsi_target.c:787
> #12 0xc0467027 in targstart (periph=0xc71cc700, start_ccb=0xc73bd400)
> at /usr/src/sys/cam/scsi/scsi_target.c:654
> #13 0xc044dd1d in xpt_run_dev_allocq (bus=0xc71d65c0) at
> /usr/src/sys/cam/cam_xpt.c:3765
> #14 0xc044e0ad in xpt_schedule (perph=0xc71cc700, new_priority=1) at
> /usr/src/sys/cam/cam_xpt.c:3665
> #15 0xc04684f4 in targwrite (dev=0xc7681000, uio=0xc6fe5c60, ioflag=0)
> at /usr/src/sys/cam/scsi/scsi_target.c:599
> #16 0xc0586359 in giant_write (dev=0xc7681000, uio=0xc6fe5c60,
> ioflag=0) at /usr/src/sys/kern/kern_conf.c:434
> #17 0xc054cbde in devfs_write_f (fp=0xc7631b94, uio=0xc6fe5c60,
> cred=0xc7681600, flags=0, td=0xc7889240) at
> /usr/src/sys/fs/devfs/devfs_vnops.c:1446
> #18 0xc05ff917 in dofilewrite (td=0xc7889240, fd=4, fp=0xc7631b94,
> auio=0xc6fe5c60, offset=-1, flags=0) at file.h:257
> #19 0xc05ffbf8 in kern_writev (td=0xc7889240, fd=4, auio=0xc6fe5c60)
> at /usr/src/sys/kern/sys_generic.c:402
> #20 0xc05ffc6f in write (td=0xc7889240, uap=0xc6fe5cfc) at
> /usr/src/sys/kern/sys_generic.c:318
> #21 0xc0825e75 in syscall (frame=0xc6fe5d38) at
> /usr/src/sys/i386/i386/trap.c:1101
> #22 0xc080a240 in Xint0x80_syscall () at
> /usr/src/sys/i386/i386/exception.s:262
> #23 0x00000033 in ?? ()
> Previous frame inner to this frame (corrupt stack?)
> (kgdb)
>
> Platform is a pair of HP DL580-G3 servers, quad 2.8GHz Xeon CPU's with
> 4 gigs of ram in each (x86-32/i386, not x86-64/amd64). I've tried this
> with and without the device.hints options, all resulting in a core
> dump on the target and a hang on the initiator until the card in the
> target gets reset on reboot.
>
> Any thoughts would be great. I'd like to get a SQL server up on these
> FC cards. I understand I could use iSCSI, but the powers that be have
> requested FC.
>
More information about the freebsd-scsi
mailing list