need raid controler ...

Wed Nov 8 09:11:26 UTC 2006

Hi,
	I did it somewhat differently, ie compiled a kernel with
the new driver, and booted over the net.
so far the raid is very fast (though i only tested it with two 36g disks)
	Any idea what to use for managing the raid? I'm only interested
in detecting if a disk is bad in a raid1.

	thanks,
		danny

> Hi Danny.
> 
> I installed x3650 yesterday.
> 
> http://www.adaptec.com/en-US/downloads/unix/freebsd?productId=SAS-4805&dn=Adaptec+Serial+Attached+SCSI+RAID+4805SAS
> 
> aacraid_freebsd6_drv_b11518.tgz(aacu.ko & more)
> 
> copy aacu.ko to USB FD
> 
> load kernel
> load disk0:aacu.ko
> load usb
> set hint.atkbdc.0.disabled=1
> set hint.atkbd.0.disabled=1
> boot
> ...
> After install, copy aacu.ko to /boot/modules/.
> Edit following files.
> 
> /boot/device.hints
> -hint.atkbdc.0.at="isa"
> -hint.atkbdc.0.port="0x060"
> -hint.atkbd.0.at="atkbdc"
> -hint.atkbd.0.irq="1"
> +hint.atkbdc.0.disabled="1"
> +hint.atkbd.0.disabled="1"
> 
> /boot/loader.conf
> aacu_load="YES"
> 
> # dmesg
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>         The Regents of the University of California. All rights
> reserved.
> FreeBSD 6.1-RELEASE #0: Sun May  7 04:42:56 UTC 2006
>     root at opus.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
> ACPI APIC Table: <IBM    SERVALNT>
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU            5160  @ 3.00GHz (3000.12-MHz
> 686-class CPU)  Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
> 
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> 
> Features2=0x4e3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>,<b18>>
>   AMD Features=0x20100000<NX,LM>
>   AMD Features2=0x1<LAHF>
>   Cores per package: 2
> real memory  = 3221008384 (3071 MB)
> avail memory = 3151065088 (3005 MB)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>  cpu0 (BSP): APIC ID:  0
>  cpu1 (AP): APIC ID:  1
>  cpu2 (AP): APIC ID:  6
>  cpu3 (AP): APIC ID:  7
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd0 at kbdmux0
> acpi0: <IBM SERVALNT> on motherboard
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
> acpi0: Power Button (fixed)
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x588-0x58b on acpi0
> cpu0: <ACPI CPU> on acpi0
> acpi_throttle0: <ACPI CPU Throttling> on cpu0
> cpu1: <ACPI CPU> on acpi0
> acpi_throttle1: <ACPI CPU Throttling> on cpu1
> acpi_throttle1: failed to attach P_CNT
> device_attach: acpi_throttle1 attach returned 6
> cpu2: <ACPI CPU> on acpi0
> acpi_throttle2: <ACPI CPU Throttling> on cpu2
> acpi_throttle2: failed to attach P_CNT
> device_attach: acpi_throttle2 attach returned 6
> cpu3: <ACPI CPU> on acpi0
> acpi_throttle3: <ACPI CPU Throttling> on cpu3
> acpi_throttle3: failed to attach P_CNT
> device_attach: acpi_throttle3 attach returned 6
> pcib0: <ACPI Host-PCI bridge> on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pci26: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci26
> pci27: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci27
> pci28: <ACPI PCI bus> on pcib3
> pcib4: <ACPI PCI-PCI bridge> at device 1.0 on pci27
> pci36: <ACPI PCI bus> on pcib4
> pcib5: <PCI-PCI bridge> at device 0.3 on pci26
> pci37: <PCI bus> on pcib5
> pcib6: <ACPI PCI-PCI bridge> at device 3.0 on pci0
> pci4: <ACPI PCI bus> on pcib6
> aacu0: <IBM ServeRAID 8k> port 0x5000-0x50ff mem
> 0xc9e00000-0xc9ffffff,0xc7fe0000-0xc7ffffff irq 17 at device 0.0 on pci4
> aacu0: New comm. interface enabled
> aacu0: Adaptec Raid Controller 2.0.7-1
> pcib7: <ACPI PCI-PCI bridge> at device 4.0 on pci0
> pci16: <ACPI PCI bus> on pcib7
> pcib8: <PCI-PCI bridge> at device 5.0 on pci0
> pci69: <PCI bus> on pcib8
> pcib9: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pci7: <ACPI PCI bus> on pcib9
> pcib10: <PCI-PCI bridge> at device 7.0 on pci0
> pci68: <PCI bus> on pcib10
> pci0: <base peripheral> at device 8.0 (no driver attached)
> pcib11: <ACPI PCI-PCI bridge> at device 28.0 on pci0
> pci2: <ACPI PCI bus> on pcib11
> pcib12: <PCI-PCI bridge> at device 0.0 on pci2
> pci3: <PCI bus> on pcib12
> bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B1), v0.9.5> mem
> 0xce000000-0xcfffffff irq 16 at device 0.0 on pci3
> bce0: ASIC ID 0x57081010; Revision (B1); PCI-X 64-bit 133MHz
> miibus0: <MII bus> on bce0
> brgphy0: <BCM5708C 10/100/1000baseTX PHY> on miibus0
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bce0: Ethernet address: 00:14:5e:18:41:e2
> pcib13: <ACPI PCI-PCI bridge> at device 28.1 on pci0
> pci5: <ACPI PCI bus> on pcib13
> pcib14: <PCI-PCI bridge> at device 0.0 on pci5
> pci6: <PCI bus> on pcib14
> bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B1), v0.9.5> mem
> 0xca000000-0xcbffffff irq 17 at device 0.0 on pci6
> bce1: ASIC ID 0x57081010; Revision (B1); PCI-X 64-bit 133MHz
> miibus1: <MII bus> on bce1
> brgphy1: <BCM5708C 10/100/1000baseTX PHY> on miibus1
> brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
> 1000baseTX-FDX, auto
> bce1: Ethernet address: 00:14:5e:18:41:e4
> uhci0: <UHCI (generic) USB controller> port 0x2200-0x221f irq 23 at
> device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0x2600-0x261f irq 22 at
> device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <UHCI (generic) USB controller> port 0x2a00-0x2a1f irq 23 at
> device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> usb2: <UHCI (generic) USB controller> on uhci2
> usb2: USB revision 1.0
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhci3: <UHCI (generic) USB controller> port 0x2e00-0x2e1f irq 22 at
> device 29.3 on pci0
> uhci3: [GIANT-LOCKED]
> usb3: <UHCI (generic) USB controller> on uhci3
> usb3: USB revision 1.0
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf9000000-0xf90003ff irq
> 23 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> usb4: EHCI version 1.0
> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
> usb4: <EHCI (generic) USB 2.0 controller> on ehci0
> usb4: USB revision 2.0
> uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub4: 8 ports with 8 removable, self powered
> pcib15: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci1: <ACPI PCI bus> on pcib15
> pci1: <display, VGA> at device 6.0 (no driver attached)
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <GENERIC ATA controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x480-0x48f at device 31.2 on pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
> acpi0
> sio0: type 16550A
> pmtimer0 on isa0
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xcafff,0xcb000-0xcc7ff,0xcc800-0xcdfff,0xce000-0xd2fff on isa0
> ppc0: parallel port not found.
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> ukbd0: IBM IBM RSA2, rev 1.10/0.01, addr 2, iclass 3/1
> kbd1 at ukbd0
> ums0: IBM IBM RSA2, rev 1.10/0.01, addr 2, iclass 3/1
> ums0: X report 0x0002 not supported
> device_attach: ums0 attach returned 6
> ukbd1: vendor 0x0430 product 0x0005, rev 1.00/1.02, addr 3, iclass 3/1
> kbd2 at ukbd1
> Timecounters tick every 1.000 msec
> acd0: CDRW <HL-DT-STCD-RW/DVD DRIVE GCC-4244N/1.02> at ata1-master
> UDMA33
> aacdu0: <RAID 1 (Mirror)> on aacu0
> aacdu0: 69890MB (143134720 sectors)
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #3 Launched!
> SMP: AP CPU #2 Launched!
> Trying to mount root from ufs:/dev/aacdu0s1a
> 
> > this box (ibm-x3650) is here for evaluation/test.
> > 
> > is there any available?
> > 
> > none2 at pci4:0:0: class=0x010400 card=0x95801014 chip=0x02869005
> > rev=0x02 
> > hdr=0x00
> >     vendor   = 'Adaptec Inc'
> >     device   = 'AAC-RAID (Rocket)'
> >     class    = mass storage
> >     subclass = RAID
> > 
> > dmesg|head:
> > FreeBSD 6.2-PRERELEASE #6: Thu Oct 19 11:17:12 IST 2006
> >     danny at bsd:/r+d/obj/bsd/r+d/6.2/src/sys/HUJI
> > ACPI APIC Table: <IBM    SERVALNT>
> > Timecounter "i8254" frequency 1193182 Hz quality 0
> > CPU: Intel(R) Xeon(R) CPU            5150  @ 2.66GHz (2666.78-MHz
> > K8-class CPU)
> >   Origin = "GenuineIntel"  Id = 0x6f5  Stepping = 5
> > 
> > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> > CMOV,PAT,PSE36,CLFL
> > USH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> > 
> > Features2=0x4e3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>
> > ,<b18>>
> >   AMD Features=0x20100800<SYSCALL,NX,LM>
> >   AMD Features2=0x1<LAHF>
> >   Cores per package: 2
> > real memory  = 5368709120 (5120 MB)
> > avail memory = 4113821696 (3923 MB) 
> -- 
> "OOGI Yukio" <yukio at fw1.sun-web.info>