ahd driver & PCI-X (64bit) Adaptec 39320D Ultra320 SCSI adapter
Scott Long
scottl at freebsd.org
Fri Nov 28 10:01:42 PST 2003
This should have been fixed for 4.9. Do you have rev 1.3.2.6 of
src/sys/dev/aic7xxx/aic79xx_pci.c?
Scott
Sander Smeenk wrote:
> Quoting Scott Long (scottl at freebsd.org):
>
>>>>| da0 at ahd0 bus 0 target 2 lun 0
>>>
>>>Oh um, the disks are at 0:2:0, 0:4:0, 0:8:0 and 0:10:0 on the bus.
>>>The SCSI adapter itself is at 0:6:0.
>>
>>What version of FreeBSD is this? Please send a full dmesg.
>
>
> Sorry. That's vital information, I should know beter ;)
>
> It's FreeBSD 4.9-RELEASE, 4.8-RELEASE has the same behaviour on this
> card. The dmesg is as follows:
>
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
> root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz
> CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.72-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0xf25 Stepping = 5
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Hyperthreading: 2 logical CPUs
> real memory = 2146959360 (2096640K bytes)
> avail memory = 2085761024 (2036876K bytes)
> Preloaded elf kernel "kernel" at 0xc053f000.
> Warning: Pentium 4 CPU: PSE disabled
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 20 entries at 0xc00fde80
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
> pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
> pci1: <PCI bus> on pcib1
> pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
> pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
> pci2: <PCI bus> on pcib2
> pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
> pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
> pci3: <PCI bus> on pcib3
> ahd0: <Adaptec 39320D Ultra320 SCSI adapter> port 0x7000-0x70ff,0x7400-0x74ff mem 0xfc200000-0xfc201fff irq 10 at device 1.0 on pci3
> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
> ahd1: <Adaptec 39320D Ultra320 SCSI adapter> port 0x7800-0x78ff,0x7c00-0x7cff mem 0xfc202000-0xfc203fff irq 10 at device 1.1 on pci3
> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
> pci0: <unknown card> (vendor=0x8086, dev=0x2544) at 2.1
> pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
> pci4: <PCI bus> on pcib4
> pci4: <ATI Mach64-GR graphics accelerator> at 3.0 irq 11
> fxp0: <Intel 82550 Pro/100 Ethernet> port 0x8400-0x843f mem 0xfc300000-0xfc31ffff,0xfc341000-0xfc341fff irq 11 at device 4.0 on pci4
> fxp0: Ethernet address 00:02:b3:d8:c4:0e
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.16> port 0x8440-0x847f mem 0xfc320000-0xfc33ffff irq 10 at device 5.0 on pci4
> em0: Speed:N/A Duplex:N/A
> isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH3 ATA100 controller> port 0x6c60-0x6c6f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 0
> eisa0: <EISA bus> on motherboard
> eisa0: unknown card @@@0000 (0x00000000) at slot 7
> orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xe3000-0xe3fff on isa0
> pmtimer0 on isa0
> fdc0: ready for input in output
> fdc0: cmd 3 failed at out byte 1 of 3
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> ppc0: parallel port not found.
> ahd1: PCI error Interrupt
>
>>>>>>>>>>>>>>>>>>>Dump Card State Begins <<<<<<<<<<<<<<<<<
>
> ahd1: Dumping Card State at program address 0x2c Mode 0x22
> Card was paused
> HS_MAILBOX[0x0] INTCTL[0x0] SEQINTSTAT[0x0] SAVED_MODE[0x0]
> DFFSTAT[0x30]:(CURRFIFO_0|FIFO0FREE|FIFO1FREE) SCSISIGI[0x0]:(P_DATAOUT)
> SCSIPHASE[0x0] SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE)
> SCSISEQ0[0x0] SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI)
> SEQCTL0[0x10]:(FASTMODE) SEQINTCTL[0x0] SEQ_FLAGS[0x0]
> SEQ_FLAGS2[0x0] SSTAT0[0x0] SSTAT1[0x8]:(BUSFREE)
> SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
> LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0]
> LQOSTAT1[0x0] LQOSTAT2[0x0]
>
> SCB Count = 16 CMDS_PENDING = 0 LASTSCB 0xffff CURRSCB 0x0 NEXTSCB 0x0
> qinstart = 0 qinfifonext = 0
> QINFIFO:
> WAITING_TID_QUEUES:
> Pending list:
> Total 0
> Kernel Free SCB list: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
> Sequencer Complete DMA-inprog list:
> Sequencer Complete list:
> Sequencer DMA-Up and Complete list:
>
> ahd1: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
> SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
> SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
> SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
> SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
> HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
> ahd1: FIFO1 Free, LONGJMP == 0x80ff, SCB 0x0
> SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
> SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
> SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
> SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
> HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
> LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
> ahd1: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x42
> ahd1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
>
> SIMODE0[0x6c]:(ENOVERRUN|ENIOERR|ENSELDI|ENSELDO)
> CCSCBCTL[0x0]
> ahd1: REG0 == 0x3533, SINDEX = 0x22, DINDEX = 0x0
> ahd1: SCBPTR == 0x0, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
> CDB 0 0 0 0 0 0
> STACK: 0x15 0x8 0x7 0x6 0x5 0x4 0x3 0x29
>
> ahd1: Signaled Target Abort
> ad0: 194481MB <Maxtor 6Y200P0> [395136/16/63] at ata0-master UDMA100
> acd0: CDROM <LTN526S> at ata0-slave PIO4
> Waiting 15 seconds for SCSI devices to settle
> Mounting root from ufs:/dev/ad0s1a
> da0 at ahd0 bus 0 target 2 lun 0
> da0: <MAXTOR ATLAS10K4_36WLS DFV0> Fixed Direct Access SCSI-3 device
> da0: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled
> da0: 35074MB (71833096 512 byte sectors: 255H 63S/T 4471C)
> da1 at ahd0 bus 0 target 4 lun 0
> da1: <MAXTOR ATLAS10K4_36WLS DFV0> Fixed Direct Access SCSI-3 device
> da1: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled
> da1: 35074MB (71833096 512 byte sectors: 255H 63S/T 4471C)
> da2 at ahd0 bus 0 target 8 lun 0
> da2: <MAXTOR ATLAS10K4_36WLS DFV0> Fixed Direct Access SCSI-3 device
> da2: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled
> da2: 35074MB (71833096 512 byte sectors: 255H 63S/T 4471C)
> da3 at ahd0 bus 0 target 10 lun 0
> da3: <MAXTOR ATLAS10K4_36WLS DFV0> Fixed Direct Access SCSI-3 device
> da3: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled
> da3: 35074MB (71833096 512 byte sectors: 255H 63S/T 4471C)
> vinum: /dev is mounted read-only, not rebuilding /dev/vinum
> swapon:
> /dev/ad0s1b
> :
> Device not configured
> Automatic boot in progress...
> /dev/ad0s1a:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s1a:
> clean, 1014151 free
> (863 frags, 126661 blocks, 0.1% fragmentation)
> /dev/vinum/usr:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/vinum/usr:
> clean, 11413419 free
> (2819 frags, 1426325 blocks, 0.0% fragmentation)
> /dev/vinum/var:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/vinum/var:
> clean, 24376115 free
> (123 frags, 3046999 blocks, 0.0% fragmentation)
> /dev/ad0s1e:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s1e:
> clean, 258029 free
> (21 frags, 32251 blocks, 0.0% fragmentation)
> /dev/vinum/varweb:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/vinum/varweb:
> clean, 26733052 free
> (5140 frags, 3340989 blocks, 0.0% fragmentation)
> /dev/ad0s1g:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s1g:
> clean, 38221667 free
> (11 frags, 4777707 blocks, 0.0% fragmentation)
> /dev/ad0s1h:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s1h:
> clean, 45115049 free
> (17 frags, 5639379 blocks, 0.0% fragmentation)
> /dev/ad0s1f:
> FILESYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad0s1f:
> clean, 12903285 free
> (13 frags, 1612909 blocks, 0.0% fragmentation)
> Doing initial network setup:
> hostname
> .
> fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> inet6 fe80::202:b3ff:fed8:c40e%fxp0 prefixlen 64 scopeid 0x1
> inet xxx.xxx.xx.xxx netmask 0xffffff00 broadcast xxx.xxx.xx.xxx
> ether 00:02:b3:d8:c4:0e
> media: Ethernet autoselect (100baseTX <full-duplex>)
> status: active
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> inet6 ::1 prefixlen 128
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
> inet 127.0.0.1 netmask 0xff000000
> Additional routing options:
> TCP keepalive=YES
> .
> Routing daemons:
> .
> Additional daemons:
> syslogd
> Nov 28 15:44:19 rood /kernel: <<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> .
> Doing additional network setup:
> .
> Starting final network daemons:
> .
> ELF ldconfig path: /usr/lib /usr/lib/compat /usr/local/lib
> a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
> Starting standard daemons:
> inetd
> cron
> sshd
> sendmail
> sendmail-clientmqueue
> .
> Initial rc.i386 initialization:
> .
> Configuring syscons:
> blanktime
> .
> Additional ABI support:
> linux
> .
> Local package initialization:
> .
> Additional TCP options:
> .
>
> Fri Nov 28 15:44:21 CET 2003
>
> Thanks,
> Sander.
>
More information about the freebsd-scsi
mailing list