aic7902: Ultra320 and ses with SEAGATE ST318452LW

[Don Bowman]

I'm finding that I don't get any ses device with this
adapter.

The system is a supermicro x5dpr motherboard, 2x 2.8GHz
XEON with 533MHz FSB. The adaptec 7902 is onboard in this
system.

I've done a MAKEDEV ses0. When I run 'getencstat -v /dev/ses0',
I get:
/dev/ses0: Device not configured

In my config I have:
device          scbus           # SCSI bus (required)
device          da              # Direct Access (disks)
device          sa              # Sequential Access (tape etc)
device          cd              # CD
device          ses             #SCSI SES/SAF-TE driver

Does anyone have any suggestions? I've also tried adding
SES_ENABLE_PASSTHROUGH and 'device pass'

When I boot with verbose, I do not see any messages come out
about ses at all. All I see that is scsi related is below:

(ahd0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 3f
(ahd0:A:0:0): Received PPR width 1, period 9, offset 3f,options 2
        Filtered to width 1, period 9, offset 3f, options 2
ahd0: target 0 using 16bit transfers
ahd0: target 0 synchronous with period = 0x9, offset = 0x3f(DT)
Creating DISK da0
pass0 at ahd0 bus 0 target 0 lun 0
pass0: <SEAGATE ST318452LW 0004> Fixed Direct Access SCSI-3 device
pass0: Serial Number 3EV00Q0500007234TRZ8
pass0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da0 at ahd0 bus 0 target 0 lun 0
da0: <SEAGATE ST318452LW 0004> Fixed Direct Access SCSI-3 device
da0: Serial Number 3EV00Q0500007234TRZ8
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 1638629, size 1638567 : OK
da0s2: type 0xa5, start 1638630, end = 35487584, size 33848955 : OK
da0: raw partition size != slice size
da0: start 63, end 1638629, size 1638567
da0c: start 63, end 1622564, size 1622502

ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0x5000-0x50ff,0x5400-0x54ff mem 0xfc400000-0xfc401fff irq 20 at device 2.0
on pci4
ahd0: Defaulting to MEMIO on
ahd0: Reading SEEPROM...done.
ahd0: STPWLEVEL is on
ahd0: Manual Primary Termination
ahd0: Manual Secondary Termination
ahd0: Primary High byte termination Enabled
ahd0: Primary Low byte termination Enabled
ahd0: Secondary High byte termination Disabled
ahd0: Secondary Low byte termination Disabled
ahd0: Downloading Sequencer Program... 716 instructions downloaded
ahd0: Features 0x101, Bugs 0xfffff, Flags 0x43f0
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0x5800-0x58ff,0x5c00-0x5cff mem 0xfc402000-0xfc403fff irq 21 at device 2.1
on pci4
ahd1: Defaulting to MEMIO on
ahd1: Reading SEEPROM...done.
ahd1: STPWLEVEL is on
ahd1: Manual Primary Termination
ahd1: Manual Secondary Termination
ahd1: Primary High byte termination Enabled
ahd1: Primary Low byte termination Enabled
ahd1: Secondary High byte termination Disabled
ahd1: Secondary Low byte termination Disabled
ahd1: Downloading Sequencer Program... 716 instructions downloaded
ahd1: Features 0x101, Bugs 0xfffff, Flags 0x43f0
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs