dmesg with Adaptec 2120S

[Scott Long]

Hi,

The warnings are harmless.  However, the 'aacp' device is a bit of a
hack and should be turned off unless you have a specific need for it.

Scott

HongChye Tan wrote:
> Hi,
> 
> I just installed a Adaptec 2120S card on Intel SE7501WV2 since the 
> hostraid is not supported.
> I configured the RAID 1 using 2 Maxtor Drives and managed to install 
> FreeBSD 5.1. It is running and i managed to reboot the server. However, 
> I got the message below from dmesg, appreciate if you could give me some 
> advise.
> 
> aac0: <Adaptec SCSI RAID 2120S> mem 0xf8000000-0xfbffffff irq 9 at 
> device 9.0 on pci3
> aac0: i960RX 100MHz, 48MB cache memory, optional battery present
> aac0: Kernel 4.0-0, Build 6003, S/N b81f0f
> aac0: Supported 
> Options=1f7e<CLUSTERS,WCACHE,DATA64,HOSTTIME,RAID50,WINDOW4GB,SOFTERR,NORECOND,SGMAP64,ALARM,NONDASD> 
> 
> aacp0: <SCSI Passthrough Bus> on aac0
> .
> .
> .
> aacd0: <RAID 1 (Mirror)> on aac0
> aacd0: 35073MB (71831040 sectors)
> (probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
> (probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
> (probe6:aacp0:0:6:0): Invalid field in CDB
> (probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
> (probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
> (probe6:aacp0:0:6:0): Invalid field in CDB
> (probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
> (probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
> (probe6:aacp0:0:6:0): Invalid field in CDB
> (probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
> (probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
> (probe6:aacp0:0:6:0): Invalid field in CDB
> (probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
> (probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
> (probe6:aacp0:0:6:0): Invalid field in CDB
> (probe1:aacp0:0:6:1): INQUIRY. CDB: 12 20 0 0 24 0
> (probe1:aacp0:0:6:1): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:1): Logical unit not supported
> (probe1:aacp0:0:6:2): INQUIRY. CDB: 12 40 0 0 24 0
> (probe1:aacp0:0:6:2): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:2): Logical unit not supported
> (probe1:aacp0:0:6:3): INQUIRY. CDB: 12 60 0 0 24 0
> (probe1:aacp0:0:6:3): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:3): Logical unit not supported
> (probe1:aacp0:0:6:4): INQUIRY. CDB: 12 80 0 0 24 0
> (probe1:aacp0:0:6:4): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:4): Logical unit not supported
> (probe1:aacp0:0:6:5): INQUIRY. CDB: 12 a0 0 0 24 0
> (probe1:aacp0:0:6:5): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:5): Logical unit not supported
> (probe1:aacp0:0:6:6): INQUIRY. CDB: 12 c0 0 0 24 0
> (probe1:aacp0:0:6:6): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:6): Logical unit not supported
> (probe1:aacp0:0:6:7): INQUIRY. CDB: 12 e0 0 0 24 0
> (probe1:aacp0:0:6:7): ILLEGAL REQUEST asc:25,0
> (probe1:aacp0:0:6:7): Logical unit not supported
> ses0 at aacp0 bus 0 target 6 lun 0
> ses0: <ESG-SHV SCA HSBP M16 0.05> Fixed unknown SCSI-2 device
> ses0: 3.300MB/s transfers
> ses0: SAF-TE Compliant Device
> pass0 at aacp0 bus 0 target 0 lun 0
> pass0: <MAXTOR ATLAS10K4_36SCA DFL0> Fixed unknown SCSI-3 device
> pass0: 160.000MB/s transfers (80.000MHz, offset 127, 16bit)
> pass1 at aacp0 bus 0 target 2 lun 0
> pass1: <MAXTOR ATLAS10K4_36SCA DFL0> Fixed unknown SCSI-3 device
> pass1: 160.000MB/s transfers (80.000MHz, offset 127, 16bit)
> Mounting root from ufs:/dev/aacd0s1a
> 
> My firmware version for the Adaptec card is Version 4 Build 6003 and i 
> the card is set at default 320MB/s
> 
> Thanks for your time.
> chye
> _______________________________________________
> freebsd-scsi at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-scsi
> To unsubscribe, send any mail to "freebsd-scsi-unsubscribe at freebsd.org"
>