dmesg with Adaptec 2120S

[HongChye Tan]

Hi,

I just installed a Adaptec 2120S card on Intel SE7501WV2 since the hostraid 
is not supported.
I configured the RAID 1 using 2 Maxtor Drives and managed to install 
FreeBSD 5.1. It is running and i managed to reboot the server. However, I 
got the message below from dmesg, appreciate if you could give me some advise.

aac0: <Adaptec SCSI RAID 2120S> mem 0xf8000000-0xfbffffff irq 9 at device 
9.0 on pci3
aac0: i960RX 100MHz, 48MB cache memory, optional battery present
aac0: Kernel 4.0-0, Build 6003, S/N b81f0f
aac0: Supported 
Options=1f7e<CLUSTERS,WCACHE,DATA64,HOSTTIME,RAID50,WINDOW4GB,SOFTERR,NORECOND,SGMAP64,ALARM,NONDASD>
aacp0: <SCSI Passthrough Bus> on aac0
.
.
.
aacd0: <RAID 1 (Mirror)> on aac0
aacd0: 35073MB (71831040 sectors)
(probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
(probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:aacp0:0:6:0): Invalid field in CDB
(probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
(probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:aacp0:0:6:0): Invalid field in CDB
(probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
(probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:aacp0:0:6:0): Invalid field in CDB
(probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
(probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:aacp0:0:6:0): Invalid field in CDB
(probe6:aacp0:0:6:0): Vendor Specific Command. CDB: 12 1 80 0 ff 0
(probe6:aacp0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:aacp0:0:6:0): Invalid field in CDB
(probe1:aacp0:0:6:1): INQUIRY. CDB: 12 20 0 0 24 0
(probe1:aacp0:0:6:1): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:1): Logical unit not supported
(probe1:aacp0:0:6:2): INQUIRY. CDB: 12 40 0 0 24 0
(probe1:aacp0:0:6:2): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:2): Logical unit not supported
(probe1:aacp0:0:6:3): INQUIRY. CDB: 12 60 0 0 24 0
(probe1:aacp0:0:6:3): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:3): Logical unit not supported
(probe1:aacp0:0:6:4): INQUIRY. CDB: 12 80 0 0 24 0
(probe1:aacp0:0:6:4): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:4): Logical unit not supported
(probe1:aacp0:0:6:5): INQUIRY. CDB: 12 a0 0 0 24 0
(probe1:aacp0:0:6:5): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:5): Logical unit not supported
(probe1:aacp0:0:6:6): INQUIRY. CDB: 12 c0 0 0 24 0
(probe1:aacp0:0:6:6): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:6): Logical unit not supported
(probe1:aacp0:0:6:7): INQUIRY. CDB: 12 e0 0 0 24 0
(probe1:aacp0:0:6:7): ILLEGAL REQUEST asc:25,0
(probe1:aacp0:0:6:7): Logical unit not supported
ses0 at aacp0 bus 0 target 6 lun 0
ses0: <ESG-SHV SCA HSBP M16 0.05> Fixed unknown SCSI-2 device
ses0: 3.300MB/s transfers
ses0: SAF-TE Compliant Device
pass0 at aacp0 bus 0 target 0 lun 0
pass0: <MAXTOR ATLAS10K4_36SCA DFL0> Fixed unknown SCSI-3 device
pass0: 160.000MB/s transfers (80.000MHz, offset 127, 16bit)
pass1 at aacp0 bus 0 target 2 lun 0
pass1: <MAXTOR ATLAS10K4_36SCA DFL0> Fixed unknown SCSI-3 device
pass1: 160.000MB/s transfers (80.000MHz, offset 127, 16bit)
Mounting root from ufs:/dev/aacd0s1a

My firmware version for the Adaptec card is Version 4 Build 6003 and i the 
card is set at default 320MB/s

Thanks for your time.
chye