megacli and PERC5 (PowerEdge 1950) on 6.2
Brian A. Seklecki
lavalamp at spiritual-machines.org
Fri Jun 1 19:15:29 UTC 2007
amd64/113232 opened
http://www.freebsd.org/cgi/query-pr.cgi?pr=113232
~BAS
On Fri, 1 Jun 2007, Brian A. Seklecki wrote:
> I'm buying free beer in unsound quantities for the commiter of this
> patch. And for the author, well... that's best discussed offline >:}
>
>
> [seklecki at db06 ~]$ sudo megacli -AdpAllInfo -aALL
> Password:
>
> Adapter #0
>
> ==============================================================================
> Versions
> ================
> Product Name : PERC 5/i Integrated
> Serial No : 12345
> FW Package Build: 5.1.1-0040
> FW Version : 1.03.10-0216
> BIOS Version : MT28
> Ctrl-R Version :1.04-017A
>
> Pending Images In Flash
> ================
> None
>
> PCI Info
> ================
> Vendor Id : 1028
> Device Id : 0015
> SubVendorId : 1028
> SubDeviceId : 1f03
>
> Host Interface : PCIE
>
> Number of Frontend Port: 0
> Device Interface : PCIE
>
> Number of Backend Port: 8
> Port : Address
> 0 5000c500005dad19
> 1 5000c500005da6e9
> 2 5000c50001cf9301
> 3 5000c50001cfb2c1
> 4 5000c500049065cd
> 5 5000c50001cf9d61
> 6 0000000000000000
> 7 0000000000000000
>
> HW Configuration
> ================
> SAS Address : 50019b90cb771f00
> BBU : Present
> Alarm : Absent
> NVRAM : Present
> Serial Debugger : Present
> Memory : Present
> Flash : Present
>
> Settings
> ================
> Current Time : 14:26:27 6/1, 2007
> Predictive Fail Poll Interval : 300sec
> Interrupt Throttle Active Count : 16
> Interrupt Throttle Completion : 50us
> Rebuild Rate : 30%
> PR Rate : 30%
> Resynch Rate : 30%
> Check Consistency Rate : 30%
> Reconstruction Rate : 30%
> Cache flush interval : 4s
> Max drives to spinup at one time : 2
> Delay among spinup groups : 12s
> Physical drive coercion mode : 128MB
> Cluster mode : Disabled
> Alarm : Disabled
> Auto Rebuild : Enabled
> Battery Warning : Enabled
>
> Ecc Bucket Size : 15
> Ecc Bucket Leak Rate : 1440 Minutes
> Restore HotSpare On Insertion : Disabled
> Expose Enclosure Devices : Disabled
> Maintain PD Fail History : Disabled
> Host Request Reordering : Enabled
>
> Capabilities
> ================
> RAID Level Supported : RAID0, RAID1, RAID5, RAID10, RAID50
> Supported Drives : SAS, SATA
>
> Allowed Mixing:
> Mix In Enclosure Allowed
>
> Status
> ================
> ECC Bucket Count : 0
>
> Limitations
> ================
> Max Arms Per VD : 32
> Max Spans Per VD : 8
> Max Arrays : 128
> Max Number of VDs : 64
> Max Parallel Commands : 1008
> Max SGE Count : 80
> Max Data Transfer Size : 8192 sectors
> Max Strips PerIO : 84
> Min Stripe Size : 8kB
> Max Stripe Size : 128kB
>
> Device Present
> ================
> Virtual Drives : 2
> Degraded : 0
> Offline : 0
> Physical Devices : 7
> Disks : 6
> Critical Disks : 0
> Failed Disks : 0
>
> Supported Adapter Operations
> ================
> Rebuild Rate : Yes
> CC Rate : Yes
> BGI Rate : Yes
> Reconstruct Rate : Yes
> Patrol Read Rate : Yes
> Alarm Control : Yes
> Cluster Support : No
> BBU : Yes
> Spanning : Yes
> Dedicated Hot Spare : Yes
> revertible Hot Spares : No
> Foreign Config Import : Yes
> Self Diagnostic : Yes
> Allow Mixed Redundancy On Array : No
> Global Hot Spares : Yes
> Deny SCSI Passthrough : No
> Deny SMP Passthrough : No
> Deny STP Passthrough : No
>
> Supported VD Operations
> ================
> Read Policy : Yes
> Write Policy : Yes
> IO Policy : Yes
> Access Policy : Yes
> Disk Cache Policy : Yes
> Reconstruction : Yes
> Deny Locate : No
> Deny CC : No
>
> Supported PD Operations
> ================
> Force Online : Yes
> Force Offline : Yes
> Force Rebuild : Yes
> Deny Force Failed : No
> Deny Force Good/Bad : No
> Deny Missing Replace : No
> Deny Clear : No
> Deny Locate : No
>
> Error Counters
> ================
> Memory Correctable Errors : 0
> Memory Uncorrectable Errors : 0
>
> Cluster Information
> ================
> Cluster Permitted : No
> Cluster Active : No
>
> Default Settings
> ================
> Phy Polarity : 0
> Phy PolaritySplit : 0
> Backgroud Rate : 30
> Stripe Size : 64kB
> Flush Time : 4 seconds
> Write Policy : WB
> Read Policy : None
> Cache When BBU Bad : Disabled
> Cached IO : No
> SMART Mode : Mode 6
> Alarm Disable : No
> Coercion Mode : 128MB
> ZCR Config : IDSEL
> Dirty LED Shows Drive Activity : No
> BIOS Continue On Error : No
> Spin Down Mode : None
> Allowed Device Type : SAS/SATA Mix
> Allow Mix In Enclosure : Yes
> Allow Mix In VD : No
> Allow SATA In Cluster : No
> Max Chained Enclosures : 1
> Disable Ctrl-R : No
> Enable Web BIOS : No
> Direct PD Mapping : No
> BIOS Enumerate VDs : No
> Restore Hot Spare On Insertion : No
> Expose Enclosure Devices : No
> Maintain PD Fail History : No
>
> --
> Brian A. Seklecki <bseklecki at collaborativefusion.com>
> Collaborative Fusion, Inc.
>
>
>
>
> IMPORTANT: This message contains confidential information and is intended only for the individual named. If the reader of this message is not an intended recipient (or the individual responsible for the delivery of this message to an intended recipient), please be advised that any re-use, dissemination, distribution or copying of this message is prohibited. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.
>
>
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"
>
l8*
-lava (Brian A. Seklecki - Pittsburgh, PA, USA)
http://www.spiritual-machines.org/
"Guilty? Yeah. But he knows it. I mean, you're guilty.
You just don't know it. So who's really in jail?"
~James Maynard Keenan
More information about the freebsd-questions
mailing list