IPMI stops respond if boot in single user mode

[Alexey V. Panfilov]

21.11.2014 13:57, Alexey V. Panfilov wrote:
> Hi,
> 
> My IBM System x3250 M5 has IPMI. It shares onboard NIC Broadcom BCM5719.
> I'm setup it and IPMI works perfectly.
> But when server boots in single user mode IPMI's IP becomes unreachable.
> It occures when bge0 init.
> 
> Any hints?
> 
> Thanks.
> 
> 
> Details are:
> 
> FreeBSD 10.1-STABLE (r274690) amd64
> 
> /boot/loader.conf
> hw.bge.allow_asf=1
> 
> 
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x5719001> mem
> 0x82a50000-0x82a5ffff,0x82a40000-0x82a4ffff,0x82a30000-0x82a3ffff irq 16
> at device 0.0 on pci6
> bge0: APE FW version: NCSI v1.2.33.0
> bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5719C 1000BASE-T media interface> PHY 1 on miibus0
> brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
> bge0: Using defaults for TSO: 65518/35/2048
> bge0: Ethernet address: 6c:ae:8b:5b:74:98
> 
> 
> bge0 at pci0:6:0:0:        class=0x020000 card=0x04911014 chip=0x165714e4
> rev=0x01 hdr=0x00
>     vendor     = 'Broadcom Corporation'
>     device     = 'NetXtreme BCM5719 Gigabit Ethernet PCIe'
>     class      = network
>     subclass   = ethernet
>     bar   [10] = type Prefetchable Memory, range 64, base 0x82a50000,
> size 65536, enabled
>     bar   [18] = type Prefetchable Memory, range 64, base 0x82a40000,
> size 65536, enabled
>     bar   [20] = type Prefetchable Memory, range 64, base 0x82a30000,
> size 65536, enabled
>     cap 01[48] = powerspec 3  supports D0 D3  current D0
>     cap 03[50] = VPD
>     cap 05[58] = MSI supports 8 messages, 64 bit enabled with 1 message
>     cap 11[a0] = MSI-X supports 17 messages
>                  Table in map 0x20[0x0], PBA in map 0x20[0x1000]
>     cap 10[ac] = PCI-Express 2 endpoint max data 128(256) FLR link x2(x4)
>                  speed 5.0(5.0) ASPM disabled(L0s/L1)
>     ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected
>     ecap 0003[13c] = Serial 1 00006cae8b5b7498
>     ecap 0004[150] = Power Budgeting 1
>     ecap 0002[160] = VC 1 max VC0
> 
> 

When it boots in single-user mode and manually run:

#ifconfig bge0 up

then ipmi become accessable.

How it can be fixed automatically after system is boot in single-user mode?


-- 
With best regards,
Alexey V. Panfilov

phone: (495)678-8007 ext 6000
mail: lehis at starnet.ru

-- 
Best regards,
Alexey V. Panfilov