bge(4) + asf

[Sean Bruno]

So, I note that the tuneable bge_allow_asf is set to 0.  This
effectively disabled IPMI for a few controllers that I have.  Is there
any reason to *not* turn it on?

Sean

if_bge.c::
<snip>
static int bge_allow_asf = 0;

TUNABLE_INT("hw.bge.allow_asf", &bge_allow_asf);
</snip>

bge0 at pci0:1:0:0:	class=0x020000 card=0x01eb1028 chip=0x165914e4 rev=0x21
hdr=0x00
    vendor     = 'Broadcom Corporation'
    device     = 'NetXtreme Gigabit Ethernet PCI Express (BCM5721)'
    class      = network
    subclass   = ethernet
bge1 at pci0:2:0:0:	class=0x020000 card=0x01eb1028 chip=0x165914e4 rev=0x21
hdr=0x00
    vendor     = 'Broadcom Corporation'
    device     = 'NetXtreme Gigabit Ethernet PCI Express (BCM5721)'
    class      = network
    subclass   = ethernet


bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
0x004201> mem 0xefef0000-0xefefffff irq 33 at device 0.0 on pci1
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xefef0000
bge0: attempting to allocate 1 MSI vectors (8 supported)
msi: routing MSI IRQ 256 to vector 56
bge0: using IRQ 256 for MSI
bge0: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: OUI 0x000818, model 0x0018, rev. 0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: bpf attached
bge0: Ethernet address: 00:18:8b:7d:cc:23
bge0: [MPSAFE]
bge0: [ITHREAD]
pcib5: <ACPI PCI-PCI bridge> irq 37 at device 9.0 on pci0
pcib5:   domain            0
pcib5:   secondary bus     2
pcib5:   subordinate bus   2
pcib5:   I/O decode        0xf000-0xfff
pcib5:   memory decode     0xeff00000-0xefffffff
pcib5:   no prefetched decode
pci2: <ACPI PCI bus> on pcib5
pci2: domain=0, physical bus=2
found-> vendor=0x14e4, dev=0x1659, revid=0x21
        domain=0, bus=2, slot=0, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D3  current D0
        MSI supports 8 messages, 64 bit
        map[10]: type Memory, range 64, base 0xefff0000, size 16,
enabled
pcib5: requested memory range 0xefff0000-0xefffffff: good
pcib5: matched entry for 2.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 37
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
0x004201> mem 0xefff0000-0xefffffff irq 37 at device 0.0 on pci2
bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xefff0000
bge1: attempting to allocate 1 MSI vectors (8 supported)
msi: routing MSI IRQ 257 to vector 64
bge1: using IRQ 257 for MSI
bge1: CHIP ID 0x00004201; ASIC REV 0x04; CHIP REV 0x42; PCI-E
miibus1: <MII bus> on bge1
brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: OUI 0x000818, model 0x0018, rev. 0
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge1: bpf attached