Deterministic lockup / panic in networking stack with ipfw / natd
enabled on recent amd64 STABLE / CURRENT
Garrett Cooper
yanefbsd at gmail.com
Tue Jun 15 21:12:56 UTC 2010
Hi,
I'm experiencing a deterministic situation on a development box I
manage when I do the following to enable ipfw and natd to bridge a
network with two bce(4) enabled NICs, where if I do the following
steps below, then try to push a few tcp frames through, the kernel
either hardlocks, or panics in the bce(4) code, ipfw(4) code or
networking stack code.
My kernel is relatively vanilla (I just turned off a number of
drivers that I don't use because the hardware support isn't there),
and all of the networking options available in GENERIC are enabled as
well. I have ipfw, ipfw_nat, and libalias built as modules, along with
bce and em.
I've included the stats on the machine. Note that it is a dual
SMT-enabled quad core machine with 8GB of RAM. I haven't done anything
to pimp the box settings via make.conf whatsoever. I would provide a
crashdump, but dumpon is broken on the box (which is extremely
annoying). Please note that pf doesn't have any issues pushing packets
with similar rules.
This has occurred on both 8-STABLE (r209169), and 9-CURRENT (r208809).
Here's the manual procedure for reproducing the issue:
# Do the following steps (this isn't automated apparently as it
completely blocks off a running box, when using ipfw restart is run).
# Copy the 8.0-RELEASE copy of rc.firewall over
cp -p /usr/src/etc/rc.firewall /etc
# Make sure you have access via ssh being redirected via natd.
echo "redirect_port tcp 192.168.10.1:22 22" > /etc/natd.conf
# Enable all of the required services and knobs
cat >> /etc/rc.conf <<EOF
firewall_enable="YES"
firewall_logging="YES"
firewall_nat_enable="YES"
firewall_nat_interface="bce1"
firewall_type="open"
gateway_enable="YES"
ipfw_enable="YES"
natd_enable="YES"
natd_interface="bce1"
natd_flags="-dynamic -d -m"
EOF
# Add the needed firewall rule after `Allow setup of incoming email'.
echo '${fwcmd} add 10 allow tcp from any to me 22 keep-state' >>
/etc/rc.firewall
# Start ipfw.
/etc/rc.d/ipfw start
#
# To cause either a panic or lockup, you can also do something simple like
# open up an ssh connection beforehand, and just open a textfile (say
rc.firewall),
# then page up and page down the textfile.
#
# My recommendation for absolute determinism though is to transfer a
large file via
# scp, like so:
#
# dd if=/dev/zero of=largefile bs=10m count=20
# scp largefile <remote-host>:
#
# The scp was how the issue was discovered originally.
#
I'm poking around with the box to get a textdump and kernel core,
because it appears to be alluding me at the moment. I'll track down
whether or not the MFC via r205511 had anything to do with this by
using a GENERIC kernel. I've also pruned all of the awesome settings
that someone else set in loader.conf to see if that is fubaring up the
system.
If you need any more details or need for me to test this problem
out in my environment, please let me know.
Thanks,
-Garrett
PS Please CC me in all emails as I'm not subscribed to this list.
$ kldstat -v
Id Refs Address Size Name
1 7 0xffffffff80100000 822f70 kernel (/boot/kernel/kernel)
Contains modules:
Id Name
64 ataraid
167 if_lo
215 elf32
155 elf64
156 shell
141 pseudofs
171 mld
170 igmp
169 if_vlan
165 if_faith
166 if_gif
168 if_tun
160 sysvmsg
163 sem
161 sysvsem
162 sysvshm
178 krpc
176 nfssvc
175 nfsserver
177 nfslockd
172 nfs_common
179 ufs
173 nfs
154 cd9660
140 procfs
139 msdosfs
138 devfs
35 ata
7 cam
15 pass
11 probe
150 g_part_mbr
149 g_part_gpt
148 g_part_ebr
147 g_part_bsd
13 ada
8 xpt
14 da
12 cd
9 aprobe
10 pmp
125 at91_udp/usbus
124 uss820/usbus
123 pci/uhci
122 pci/ohci
121 pci/ehci
41 pci/ata_acard
120 pci/uart
119 isa/uart
118 acpi/uart
40 pci/ata_ahci
39 atapci/ata_ahci_ata
117 random
116 pci/ppc
115 isa/ppc
114 acpi/ppc
113 ppbus/ppi
174 nfslock
23 acpi/acpi_isab
112 ppc/ppbus
111 ppbus/lpt
38 pci/atapci
110 pci/vgapci
109 pci/pcib
108 pcib/pci
37 atapci/ata
36 isa/ata
29 cpu/acpi_perf
18 acpi/acpi_button
219 cpu/p4tcc
218 cpu/hwpstate
28 pci/acpi_pcib
27 acpi/acpi_pcib
217 cpu/est
216 cpu/powernow
22 acpi/acpi_hpet
20 acpi/cpu
107 pci/isab
106 pci/ignore_pci
105 pci/hostb
214 isa/vga
213 vgapci/vgapm
104 pci/fixup_pci
212 isa/sc
211 isa/atrtc
210 acpi/atrtc
103 null
209 scrndr-vga
208 scterm-scteken
207 io
102 miibus/xmphy
101 miibus/ukphy
206 atkbdc/psm
205 isa/psmcpnp
204 acpi/psmcpnp
100 miibus/truephy
203 isa/atkbdc
202 acpi/atkbdc
201 atkbdc/atkbd
200 hostb/agp_via
199 hostb/agp_intel
198 vgapci/agp_i810
197 hostb/agp_amd64
157 cpu/cpufreq
99 miibus/tlphy
196 legacy/pcib
195 isa/pcibus_pnp
194 isa/atdma
193 acpi/atdma
192 legacy/isa
98 miibus/tdkphy
97 miibus/smcphy
191 isa/attimer
190 acpi/attimer
96 miibus/ruephy
95 miibus/rlphy
189 root/nexus
188 nexus/ram
187 isa/sysresource
94 miibus/rgephy
93 miibus/qsphy
92 miibus/pnaphy
91 miibus/nsphyter
90 miibus/nsphy
89 miibus/nsgphy
88 miibus/mlphy
87 miibus/lxtphy
86 miibus/jmphy
85 miibus/ip1000phy
84 miibus/inphy
83 miibus/icsphy
153 isa/orm
186 nexus/legacy
185 legacy/cpu
82 miibus/gentbi
152 isab/isa
184 pci/ioapic
183 nexus/apic
151 eisab/isa
182 acpi/fpupnp
81 miibus/xlphy
80 miibus/e1000phy
79 miibus/ciphy
78 miibus/brgphy
77 miibus/bmtphy
76 miibus/axphy
75 miibus/atphy
74 miibus/amphy
73 miibus/acphy
72 mfi/mfid
181 root/nexus_acpi
71 pci/mfi
16 nexus/acpi
17 acpi/acpi_acad
26 acpi/acpi_pci_link
34 acpi/acpi_timer
70 mem
33 cpu/acpi_throttle
32 acpi/acpi_tz
19 acpi/acpi_cmbat
25 pcib/acpi_pci
31 acpi/acpi_smbat
68 kbdmux
67 cpu/ichss
30 acpi/acpi_sysresource
66 ata/acd
21 acpi/acpi_ec
65 ad/subdisk
24 acpi/acpi_lid
63 ata/ad
62 pci/ata_via
61 pci/ata_sis
60 pci/ata_sii
59 pci/ata_serverworks
58 pci/ata_promise
57 pci/ata_nvidia
56 pci/ata_netcell
55 pci/ata_national
137 watchdog
54 pci/ata_micron
136 uhub/ums
135 uhub/ukbd
134 uhub/uhid
53 pci/ata_marvell
52 pci/ata_jmicron
51 pci/ata_ite
133 uhub/ulpt
132 usbus/uhub
131 uhub/uhub
50 pci/ata_intel
49 pci/ata_highpoint
48 pci/ata_cyrix
47 pci/ata_cypress
46 pci/ata_cenatek
45 pci/ata_ati
44 pci/ata_amd
43 pci/ata_adaptec
130 uhub/usb_linux
129 uhub/umass
42 pci/ata_ali
128 ohci/usbus
127 uhci/usbus
126 ehci/usbus
144 g_vfs
146 g_part
180 g_class
143 g_disk
142 g_dev
158 rootbus
69 g_md
159 firmware
145 g_label
164 ether
220 x86bios
2 1 0xffffffff80923000 50680 if_bce.ko (/boot/kernel/if_bce.ko)
Contains modules:
Id Name
2 pci/bce
1 bce/miibus
$ uname -a
FreeBSD tameshi.cisco.com 8.1-PRERELEASE FreeBSD 8.1-PRERELEASE #0
r209169: Mon Jun 14 12:41:49 PDT 2010
root@:/usr/obj/data/scratch/src/stable/8/sys/TAMESHI_STABLE amd64
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-PRERELEASE #0 r209169: Mon Jun 14 12:41:49 PDT 2010
root@:/usr/obj/data/scratch/src/stable/8/sys/TAMESHI_STABLE amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU X5460 @ 3.16GHz (3158.76-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x10676 Family = 6 Model = 17 Stepping = 6
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 8589934592 (8192 MB)
avail memory = 8289869824 (7905 MB)
ACPI APIC Table: <DELL PE_SC3 >
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 2 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <DELL PE_SC3> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci4: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci4
pci5: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci5
pci6: <ACPI PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci6
pci7: <PCI bus> on pcib4
bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xf4000000-0xf5ffffff irq 16 at device 0.0 on pci7
miibus0: <MII bus> on bce0
brgphy0: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce0: Ethernet address: 00:1e:4f:38:65:ad
bce0: [ITHREAD]
bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(3.5.12); Flags (MSI|MFW); MFW (ipms 1.6.0)
pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci5
pci8: <ACPI PCI bus> on pcib5
pcib6: <PCI-PCI bridge> at device 0.3 on pci4
pci9: <PCI bus> on pcib6
pcib7: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib7
mfi0: <Dell PERC 6> port 0xec00-0xecff mem
0xfc480000-0xfc4bffff,0xfc440000-0xfc47ffff irq 16 at device 0.0 on
pci1
mfi0: Megaraid SAS driver Ver 3.00
mfi0: 18149 (329945474s/0x0020/info) - Shutdown command received from host
mfi0: 18150 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0060/1000/1f0c/1028)
mfi0: 18151 (boot + 3s/0x0020/info) - Firmware version 1.21.02-0528
mfi0: 18152 (boot + 3s/0x0008/info) - Battery Present
mfi0: 18153 (boot + 3s/0x0020/info) - Controller hardware revision ID (0x0)
mfi0: 18154 (boot + 3s/0x0020/info) - Package version 6.1.1-0047
mfi0: 18155 (boot + 3s/0x0020/info) - Board Revision
mfi0: 18156 (boot + 32s/0x0002/info) - Unexpected sense: Encl PD 20
Path 5001e0f03434f000, CDB: 12 00 00 00 04 00, Sense: 6/29/00
mfi0: 18157 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
communication restored
mfi0: 18158 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18159 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18160 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18161 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18162 (boot + 33s/0x0002/info) - Inserted: Encl PD 20
mfi0: 18163 (boot + 33s/0x0002/info) - Inserted: PD 20(c None/p0)
Info: enclPd=20, scsiType=d, portMap=09,
sasAddr=5001e0f03434f000,0000000000000000
mfi0: 18164 (boot + 33s/0x0002/info) - Inserted: PD 00(e0x20/s0)
mfi0: 18165 (boot + 33s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info:
enclPd=20, scsiType=0, portMap=00,
sasAddr=5000c50008fe5169,0000000000000000
mfi0: 18166 (boot + 33s/0x0002/info) - Inserted: PD 01(e0x20/s1)
mfi0: 18167 (boot + 33s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info:
enclPd=20, scsiType=0, portMap=01,
sasAddr=5000c50008fe538d,0000000000000000
mfi0: 18168 (boot + 33s/0x0002/info) - Inserted: PD 02(e0x20/s2)
mfi0: 18169 (boot + 33s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info:
enclPd=20, scsiType=0, portMap=02,
sasAddr=5000c50008fe3999,0000000000000000
mfi0: 18170 (boot + 33s/0x0002/info) - Inserted: PD 03(e0x20/s3)
mfi0: 18171 (boot + 33s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info:
enclPd=20, scsiType=0, portMap=03,
sasAddr=5000c50008fe36c9,0000000000000000
mfi0: 18172 (329945552s/0x0020/info) - Time established as 06/15/10
19:32:32; (36 seconds since power on)
mfi0: 18173 (329945584s/0x0008/info) - Battery temperature is normal
mfi0: 18174 (329945584s/0x0008/info) - Battery started charging
mfi0: 18175 (329945584s/0x0008/info) - Current capacity of the battery
is above threshold
mfi0: 18176 (329946819s/0x0008/info) - Battery charge complete
mfi0: 18177 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0060/1000/1f0c/1028)
mfi0: 18178 (boot + 3s/0x0020/info) - Firmware version 1.21.02-0528
mfi0: 18179 (boot + 3s/0x0008/info) - Battery Present
mfi0: 18180 (boot + 3s/0x0020/info) - Controller hardware revision ID (0x0)
mfi0: 18181 (boot + 3s/0x0020/info) - Package version 6.1.1-0047
mfi0: 18182 (boot + 3s/0x0020/info) - Board Revision
mfi0: 18183 (boot + 32s/0x0002/info) - Unexpected sense: Encl PD 20
Path 5001e0f03434f000, CDB: 12 00 00 00 04 00, Sense: 6/29/00
mfi0: 18184 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
communication restored
mfi0: 18185 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18186 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18187 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18188 (boot + 33s/0x0004/info) - Enclosure PD 20(c None/p0)
element (SES code 0x17) status changed
mfi0: 18189 (boot + 33s/0x0002/info) - Inserted: Encl PD 20
mfi0: 18190 (boot + 33s/0x0002/info) - Inserted: PD 20(c None/p0)
Info: enclPd=20, scsiType=d, portMap=09,
sasAddr=5001e0f03434f000,0000000000000000
mfi0: 18191 (boot + 33s/0x0002/info) - Inserted: PD 00(e0x20/s0)
mfi0: 18192 (boot + 33s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info:
enclPd=20, scsiType=0, portMap=00,
sasAddr=5000c50008fe5169,0000000000000000
mfi0: 18193 (boot + 33s/0x0002/info) - Inserted: PD 01(e0x20/s1)
mfi0: 18194 (boot + 33s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info:
enclPd=20, scsiType=0, portMap=01,
sasAddr=5000c50008fe538d,0000000000000000
mfi0: 18195 (boot + 33s/0x0002/info) - Inserted: PD 02(e0x20/s2)
mfi0: 18196 (boot + 33s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info:
enclPd=20, scsiType=0, portMap=02,
sasAddr=5000c50008fe3999,0000000000000000
mfi0: 18197 (boot + 33s/0x0002/info) - Inserted: PD 03(e0x20/s3)
mfi0: 18198 (boot + 33s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info:
enclPd=20, scsiType=0, portMap=03,
sasAddr=5000c50008fe36c9,0000000000000000
mfi0: 18199 (329947433s/0x0020/info) - Time established as 06/15/10
20:03:53; (36 seconds since power on)
mfi0: 18200 (329947465s/0x0008/info) - Battery temperature is normal
mfi0: 18201 (329947465s/0x0008/info) - Battery started charging
mfi0: 18202 (329947465s/0x0008/info) - Current capacity of the battery
is above threshold
mfi0: 18203 (329947595s/0x0008/info) - Battery charge complete
mfi0: 18204 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0060/1000/1f0c/1028)
mfi0: 18205 (boot + 3s/0x0020/info) - Firmware version 1.21.02-0528
mfi0: 18206 (boot + 3s/0x0008/info) - Battery Present
mfi0: 18207 (boot + 3s/0x0020/info) - Controller hardware revision ID (0x0)
mfi0: 18208 (boot + 3s/0x0020/info) - Package version 6.1.1-0047
mfi0: 18209 (boot + 3s/0x0020/info) - Board Revision
mfi0: 18210 (boot + 21s/0x0004/info) - Enclosure PD 20(c None/p0)
communication restored
mfi0: 18211 (boot + 21s/0x0002/info) - Inserted: Encl PD 20
mfi0: 18212 (boot + 21s/0x0002/info) - Inserted: PD 20(c None/p0)
Info: enclPd=20, scsiType=d, portMap=09,
sasAddr=5001e0f03434f000,0000000000000000
mfi0: 18213 (boot + 21s/0x0002/info) - Inserted: PD 00(e0x20/s0)
mfi0: 18214 (boot + 21s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info:
enclPd=20, scsiType=0, portMap=00,
sasAddr=5000c50008fe5169,0000000000000000
mfi0: 18215 (boot + 22s/0x0002/info) - Inserted: PD 01(e0x20/s1)
mfi0: 18216 (boot + 22s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info:
enclPd=20, scsiType=0, portMap=01,
sasAddr=5000c50008fe538d,0000000000000000
mfi0: 18217 (boot + 22s/0x0002/info) - Inserted: PD 02(e0x20/s2)
mfi0: 18218 (boot + 22s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info:
enclPd=20, scsiType=0, portMap=02,
sasAddr=5000c50008fe3999,0000000000000000
mfi0: 18219 (boot + 22s/0x0002/info) - Inserted: PD 03(e0x20/s3)
mfi0: 18220 (boot + 22s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info:
enclPd=20, scsiType=0, portMap=03,
sasAddr=5000c50008fe36c9,0000000000000000
mfi0: 18221 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0060/1000/1f0c/1028)
mfi0: 18222 (boot + 3s/0x0020/info) - Firmware version 1.21.02-0528
mfi0: 18223 (boot + 3s/0x0008/info) - Battery Present
mfi0: 18224 (boot + 3s/0x0020/info) - Controller hardware revision ID (0x0)
mfi0: 18225 (boot + 3s/0x0020/info) - Package version 6.1.1-0047
mfi0: 18226 (boot + 3s/0x0020/info) - Board Revision
mfi0: 18227 (boot + 21s/0x0004/info) - Enclosure PD 20(c None/p0)
communication restored
mfi0: 18228 (boot + 21s/0x0002/info) - Inserted: Encl PD 20
mfi0: 18229 (boot + 21s/0x0002/info) - Inserted: PD 20(c None/p0)
Info: enclPd=20, scsiType=d, portMap=09,
sasAddr=5001e0f03434f000,0000000000000000
mfi0: 18230 (boot + 21s/0x0002/info) - Inserted: PD 00(e0x20/s0)
mfi0: 18231 (boot + 21s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info:
enclPd=20, scsiType=0, portMap=00,
sasAddr=5000c50008fe5169,0000000000000000
mfi0: 18232 (boot + 22s/0x0002/info) - Inserted: PD 01(e0x20/s1)
mfi0: 18233 (boot + 22s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info:
enclPd=20, scsiType=0, portMap=01,
sasAddr=5000c50008fe538d,0000000000000000
mfi0: 18234 (boot + 22s/0x0002/info) - Inserted: PD 02(e0x20/s2)
mfi0: 18235 (boot + 22s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info:
enclPd=20, scsiType=0, portMap=02,
sasAddr=5000c50008fe3999,0000000000000000
mfi0: 18236 (boot + 22s/0x0002/info) - Inserted: PD 03(e0x20/s3)
mfi0: 18237 (boot + 22s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info:
enclPd=20, scsiType=0, portMap=03,
sasAddr=5000c50008fe36c9,0000000000000000
mfi0: [ITHREAD]
pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci10: <ACPI PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 5.0 on pci0
pci11: <PCI bus> on pcib9
pcib10: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci12: <ACPI PCI bus> on pcib10
pcib11: <PCI-PCI bridge> at device 7.0 on pci0
pci13: <PCI bus> on pcib11
pci0: <base peripheral> at device 8.0 (no driver attached)
pcib12: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib12
pcib13: <PCI-PCI bridge> at device 0.0 on pci2
pci3: <PCI bus> on pcib13
bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci3
miibus1: <MII bus> on bce1
brgphy1: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce1: Ethernet address: 00:1e:4f:38:65:ab
bce1: [ITHREAD]
bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(3.5.12); Flags (MSI|MFW); MFW (ipms 1.6.0)
uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port
0xcce0-0xccff irq 21 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0
uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port
0xccc0-0xccdf irq 20 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1
uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port
0xcca0-0xccbf irq 21 at device 29.2 on pci0
uhci2: [ITHREAD]
usbus2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2
uhci3: <Intel 631XESB/632XESB/3100 USB controller USB-4> port
0xcc80-0xcc9f irq 20 at device 29.3 on pci0
uhci3: [ITHREAD]
usbus3: <Intel 631XESB/632XESB/3100 USB controller USB-4> on uhci3
ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xfc500000-0xfc5003ff
irq 21 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 63XXESB USB 2.0 controller> on ehci0
pcib14: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci14: <ACPI PCI bus> on pcib14
vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem
0xd8000000-0xdfffffff,0xfc2d0000-0xfc2dffff irq 19 at device 13.0 on
pci14
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc8fff,0xc9000-0xc9fff,0xec000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est4 attach returned 6
p4tcc4: <CPU Frequency Thermal Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est5 attach returned 6
p4tcc5: <CPU Frequency Thermal Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est6 attach returned 6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 4921492106004921
device_attach: est7 attach returned 6
p4tcc7: <CPU Frequency Thermal Control> on cpu7
Timecounters tick every 10.000 msec
mfi0: 18238 (329948437s/0x0020/info) - Time established as 06/15/10
20:20:37; (24 seconds since power on)
mfi0: 18239 (329948481s/0x0008/info) - Battery temperature is normal
mfi0: 18240 (329948481s/0x0008/info) - Current capacity of the battery
is above threshold
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
mfid0: <MFI Logical Disk> on mfi0
mfid0: 571136MB (1169686528 sectors) RAID volume '' is optimal
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #6 Launched!
ugen3.1: <Intel> at usbus3ugen0.1: <Intel> at usbus0ugen2.1: <Intel>
at usbus2ugen1.1: <Intel> at usbus1
uhub0:
<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
uhub1:
<Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
ugen4.2: <vendor 0x04b4> at usbus4
uhub5: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr
2> on usbus4
uhub5: 4 ports with 4 removable, self powered
Root mount waiting for: usbus4
ugen4.3: <Dell> at usbus4
uhub6: <Dell USB Keyboard Hub> on usbus4
Root mount waiting for: usbus4
uhub6: 3 ports with 2 removable, bus powered
ugen4.4: <Dell> at usbus4
ukbd0: <Dell USB Keyboard Hub> on usbus4
kbd2 at ukbd0
uhid0: <Dell USB Keyboard Hub> on usbus4
Trying to mount root from ufs:/dev/mfid0s1a
More information about the freebsd-net
mailing list