The following reply was made to PR kern/112710; it has been noted by GNATS.
From: W Forms <wforms at safe-mail.net>
To: bug-followup at FreeBSD.org
Cc:
Subject: Re: kern/112710: [re] if_re driver detects incorrect b243a405a405 MAC address on SMC9452TX-1 pci gigabit cards
Date: Thu, 28 Jun 2007 22:26:29 +0200
I tested this issue today using an OpenBSD 4.1 boot CD. The test
hardware is exactly the same system my original report and tests were
based on, with only two minor exceptions:
1., the ORDER of the "5 bad" network adapters may not be the same as
with the original tests
2., for this OpenBSD test I also had a 16MB USB pendrive (sd1)
connected to dump dmesg to, which was not present for the FreeBSD and
Linux tests
Please notice how the 5 adapters all show the same "incorrect" MAC
address under OpenBSD! Exactly as with FreeBSD. I guess this is
because FreeBSD and OpenBSD uses the same driver. Could somebody
confirm that?! How about NetBSD ?
OpenBSD 4.1 (RAMDISK_CD) #248: Sat Mar 10 19:32:46 MST 2007
deraadt at i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache)
499 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,
MMX,FXSR,SSE
real mem = 536420352 (523848K)
avail mem = 483319808 (471992K)
using 4278 buffers containing 26943488 bytes (26312K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+ BIOS, date 02/09/01, BIOS32 rev. 0 @ 0xfd5e1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xffff
pcibios0: PCI BIOS has 11 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:15:0 ("ServerWorks OSB4" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x5000
acpi at mainbus0 not configured
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ServerWorks CNB20-LE Host" rev 0x04
pchb1 at pci0 dev 0 function 1 "ServerWorks CNB20-LE Host" rev 0x02
pci1 at pchb1 bus 1
re0 at pci1 dev 2 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 15, address b2:43:a4:05:a4:05
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 3
re1 at pci1 dev 3 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 9, address b2:43:a4:05:a4:05
rgephy1 at re1 phy 7: RTL8169S/8110S PHY, rev. 3
re2 at pci1 dev 4 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 10, address b2:43:a4:05:a4:05
rgephy2 at re2 phy 7: RTL8169S/8110S PHY, rev. 3
re3 at pci1 dev 5 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 11, address b2:43:a4:05:a4:05
rgephy3 at re3 phy 7: RTL8169S/8110S PHY, rev. 3
re4 at pci0 dev 1 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 11, address b2:43:a4:05:a4:05
rgephy4 at re4 phy 7: RTL8169S/8110S PHY, rev. 3
ahc0 at pci0 dev 6 function 0 "Adaptec AIC-7895" rev 0x04: irq 15
scsibus0 at ahc0: 16 targets
ahc1 at pci0 dev 6 function 1 "Adaptec AIC-7895" rev 0x04: irq 10
scsibus1 at ahc1: 16 targets
sd0 at scsibus1 targ 0 lun 0: <QUANTUM, QM39100TD-SCA, N1K0> SCSI2 0/
direct fixed
sd0: 8683MB, 8057 cyl, 10 head, 220 sec, 512 bytes/sec, 17783249 sec
total
st0 at scsibus1 targ 6 lun 0: <Seagate, STT20000N, 7A64> SCSI2 1/
sequential removable
scsibus1 targ 14 lun 0: <SDR, GEM200, 2> SCSI2 3/processor fixed not
configured
pcn0 at pci0 dev 9 function 0 "AMD 79c970 PCnet-PCI" rev 0x36,
Am79c972, rev 6: irq 11, address 00:06:29:50:d9:9e
nsphyter0 at pcn0 phy 1: DP83843 10/100 PHY, rev. 0
ukphy0 at pcn0 phy 31: Generic IEEE 802.3u media interface, rev. 1:
OUI 0x00001a, model 0x0001
ifmedia_set: no match for 0x20/0xffffffff
vga1 at pci0 dev 10 function 0 "S3 Trio64V2/DX" rev 0x16
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 15 function 0 "ServerWorks OSB4" rev 0x4d
pciide0 at pci0 dev 15 function 1 "ServerWorks IDE" rev 0x4a: DMA
(unsupported), channel 0 configured to compatibility, channel 1
configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <SONY, CD-ROM CDU701-F, 1.0s> SCSI0 5/
cdrom removable
pciide0: no compatibility interrupt for use by channel 1
ohci0 at pci0 dev 15 function 2 "ServerWorks OSB4/CSB5 USB" rev 0x04:
irq 10, version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ServerWorks OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f5e5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: vendor 0x0c76 product 0x0005, rev 1.10/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets
sd1 at scsibus3 targ 1 lun 0: <Easy, Disk, 1.00> SCSI2 0/direct
removable
sd1: 15MB, 15 cyl, 64 head, 32 sec, 512 bytes/sec, 31263 sec total
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous at 5.7MHz, offset = 0x8
dkcsum: sd0 matches BIOS drive 0x80
root on rd0a
rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
sd1(umass0:1:0): Check Condition (error 0x70) on opcode 0x2a
SENSE KEY: Write Protected
ASC/ASCQ: ASC 0x27 ASCQ 0x00
umass0: at uhub0 port 2 (addr 2) disconnected
sd1 detached
scsibus3 detached
umass0 detached
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: vendor 0x0c76 product 0x0005, rev 1.10/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets
sd1 at scsibus3 targ 1 lun 0: <Easy, Disk, 1.00> SCSI2 0/direct
removable
sd1: 15MB, 15 cyl, 64 head, 32 sec, 512 bytes/sec, 31263 sec total
umass0: at uhub0 port 2 (addr 2) disconnected
sd1 detached
scsibus3 detached
umass0 detached
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: vendor 0x0c76 product 0x0005, rev 1.10/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets
sd1 at scsibus3 targ 1 lun 0: <Easy, Disk, 1.00> SCSI2 0/direct
removable
sd1: 15MB, 15 cyl, 64 head, 32 sec, 512 bytes/sec, 31263 sec total
Regards,
Keve