ThinkPad T400
Russell Jackson
raj at csub.edu
Sun Sep 7 18:51:29 UTC 2008
I received my t400 at last, and I thought I'd share my experiences with
it so far.
Very nice piece of hardware --to me anyway; this is my first ThinkPad.
Either I'm lucky or the assembly line problems have been worked out
because I'm not having the heat problems that other's have been
reporting with the t4x/6x series. It runs comfortably --maybe a little
warm-- on my lap even during a long compile run (under Linux; see
below). This is in contrast to my previous --Dell-- laptop which would
get scorching hot under the same load.
Unfortunately, 7.0-RELEASE will not boot with ACPI enabled. Though it
will boot without ACPI, neither the em nor ath drivers successfully
probe their respective hardware. Without ACPI, I didn't even bother
continuing with the installation.
I tried the August 8.0-CURRENT snapshot which booted with ACPI, and the
em driver seemed to support for the NIC as I was able to get a DHCP
lease from sysinstall. Unfortunately --again--, the August snapshot has
a bug in gnutar that prevents sysinstall from working, so I didn't
actually get past sysinstall. The bug is supposedly fixed in HEAD, but
there isn't a September snapshot yet. I can't figure another convenient
way to get CURRENT on here; so, FreeBSD is dead in the water for me at
this point unless I want build my own snapshot or somebody has a better
idea...
I've been running Ubuntu for the last couple of days which has more or
less been working flawlessly. Suspend even works... most of the time.
The only major issues I had were with madwifi and the intel xorg driver.
The HAL from madwifi didn't support my card, but that was fixed building
a patched snapshot that included the newly released HAL that did. The
other issue was with the intel video driver hanging when using the Xv
extension. That was solved by building a newer release from source.
I've been impressed with the Intel video; I've never had such good
quality and performance from an opensource xfree86/xorg driver before.
It's nice being free from the nvidia binary blob. This laptop also has
an ATI Radeon 3470 in addition to the GM45 Intel graphics, but the
radeonhd driver is not yet practical, and the fglrx binary driver
crashed just starting the X server. Bleh.
Battery life has been incredible compared to what I was getting with my
old Dell; I'd be lucky to an hour out of it tops. I'm getting 2 hours
plus doing real work on this bad boy even with the tiny 4-cell battery.
I'm still waiting for the 9-cell to come in. Apparently there's a world
wide battery shortage causing delays.
I've attached the Linux dmesg boot output and lspci -vv output for now.
When I can get a working FreeBSD configuration, I'll post their equivalents.
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation Cantiga Memory Controller Hub (rev 07)
Subsystem: Lenovo Unknown device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation Cantiga Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Lenovo Unknown device 2112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Cantiga Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Unknown device 2112
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at f4200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation Cantiga MEI Controller (rev 07)
Subsystem: Lenovo Unknown device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc226800 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Unknown device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 218
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0300c Data: 4162
Capabilities: [e0] #13 [0306]
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] #13 [0306]
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] #13 [0306]
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] #13 [0306]
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Unknown device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 18
Region 0: Memory at fc226c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] #13 [0306]
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Unknown device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fc020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee0300c Data: 41c9
Capabilities: [90] Subsystem: Lenovo Unknown device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f4300000-f43fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee0300c Data: 41d1
Capabilities: [90] Subsystem: Lenovo Unknown device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee0300c Data: 41d9
Capabilities: [90] Subsystem: Lenovo Unknown device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4100000-00000000f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <1us, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 4, PowerLimit 6.500000
Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee0300c Data: 41e1
Capabilities: [90] Subsystem: Lenovo Unknown device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] #13 [0306]
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 18e0 [size=32]
Capabilities: [50] #13 [0306]
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Unknown device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [50] #13 [0306]
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Unknown device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] #13 [0306]
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 00004000-00007fff
Memory behind bridge: f4800000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Lenovo Unknown device 20f4
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Unknown device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Unknown device 20f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 219
Region 0: I/O ports at 1c48 [size=8]
Region 1: I/O ports at 183c [size=4]
Region 2: I/O ports at 1c40 [size=8]
Region 3: I/O ports at 1838 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fc226000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+
Address: fee0300c Data: 414a
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
Capabilities: [b0] #13 [0306]
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Unknown device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc227400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
03:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01)
Subsystem: Atheros Communications Inc. Unknown device 0035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f4300000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [60] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <512ns, L1 <64us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
Subsystem: Lenovo Unknown device 20c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: c0000000-c3fff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: Lenovo Unknown device 20c7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at f4801000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
-------------- next part --------------
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd at terranova) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Aug 20 22:56:21 UTC 2008 (Ubuntu 2.6.24-19.41-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
[ 0.000000] BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bc4a1000 (usable)
[ 0.000000] BIOS-e820: 00000000bc4a1000 - 00000000bc4a7000 (reserved)
[ 0.000000] BIOS-e820: 00000000bc4a7000 - 00000000bc5b7000 (usable)
[ 0.000000] BIOS-e820: 00000000bc5b7000 - 00000000bc60f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bc60f000 - 00000000bc6c6000 (usable)
[ 0.000000] BIOS-e820: 00000000bc6c6000 - 00000000bc6d1000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bc6d1000 - 00000000bc6d4000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bc6d4000 - 00000000bc6d8000 (reserved)
[ 0.000000] BIOS-e820: 00000000bc6d8000 - 00000000bc6dc000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bc6dc000 - 00000000bc6df000 (reserved)
[ 0.000000] BIOS-e820: 00000000bc6df000 - 00000000bc706000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bc706000 - 00000000bc708000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bc708000 - 00000000bc90f000 (reserved)
[ 0.000000] BIOS-e820: 00000000bc90f000 - 00000000bc99f000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bc99f000 - 00000000bc9ff000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bc9ff000 - 00000000bca00000 (usable)
[ 0.000000] BIOS-e820: 00000000bcc00000 - 00000000bf000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
[ 0.000000] 2122MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f6590
[ 0.000000] Entering add_active_range(0, 0, 772608) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 772608
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 772608
[ 0.000000] On node 0 totalpages: 772608
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 4244 pages used for memmap
[ 0.000000] HighMem zone: 538988 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6550 checksum 0
[ 0.000000] ACPI: RSDP 000F6550, 0024 (r2 LENOVO)
[ 0.000000] ACPI: XSDT BC96A4DE, 009C (r1 LENOVO TP-7U 1130 LTP 0)
[ 0.000000] ACPI: FACP BC96A600, 00F4 (r3 LENOVO TP-7U 1130 LNVO 1)
[ 0.000000] ACPI: DSDT BC96A9DB, F190 (r1 LENOVO TP-7U 1130 MSFT 3000000)
[ 0.000000] ACPI: FACS BC98E000, 0040
[ 0.000000] ACPI: SSDT BC96A7B4, 0227 (r1 LENOVO TP-7U 1130 MSFT 3000000)
[ 0.000000] ACPI: ECDT BC979B6B, 0052 (r1 LENOVO TP-7U 1130 LNVO 1)
[ 0.000000] ACPI: APIC BC979BBD, 0078 (r1 LENOVO TP-7U 1130 LNVO 1)
[ 0.000000] ACPI: MCFG BC979C35, 003C (r1 LENOVO TP-7U 1130 LNVO 1)
[ 0.000000] ACPI: HPET BC979C71, 0038 (r1 LENOVO TP-7U 1130 LNVO 1)
[ 0.000000] ACPI: SLIC BC979DC2, 0176 (r1 LENOVO TP-7U 1130 LTP 0)
[ 0.000000] ACPI: BOOT BC979F38, 0028 (r1 LENOVO TP-7U 1130 LTP 1)
[ 0.000000] ACPI: ASF! BC979F60, 00A0 (r16 LENOVO TP-7U 1130 PTL 1)
[ 0.000000] ACPI: SSDT BC98D213, 054F (r1 LENOVO TP-7U 1130 INTL 20050513)
[ 0.000000] ACPI: TCPA BC707000, 0032 (r0 0 0)
[ 0.000000] ACPI: DMAR BC706000, 00C0 (r1 1 0)
[ 0.000000] ACPI: SSDT BC6D3000, 0655 (r1 PmRef CpuPm 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT BC6D2000, 0274 (r1 PmRef Cpu0Tst 3000 INTL 20050624)
[ 0.000000] ACPI: SSDT BC6D1000, 0242 (r1 PmRef ApTst 3000 INTL 20050624)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 7:7 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 7:7 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: bf000000:21000000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 766572
[ 0.000000] Kernel command line: root=/dev/mapper/sys-root ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2261.022 MHz processor.
[ 10.042713] Console: colour VGA+ 80x25
[ 10.042719] console [tty0] enabled
[ 10.043177] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 10.043734] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 10.359307] Memory: 3048256k/3090432k available (2177k kernel code, 37092k reserved, 1006k data, 368k init, 2169252k highmem)
[ 10.359322] virtual kernel memory layout:
[ 10.359324] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 10.359327] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 10.359329] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 10.359331] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 10.359333] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 10.359335] .data : 0xc03204c4 - 0xc041bdc4 (1006 kB)
[ 10.359337] .text : 0xc0100000 - 0xc03204c4 (2177 kB)
[ 10.359344] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 10.359409] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 10.359537] hpet clockevent registered
[ 10.439386] Calibrating delay using timer specific routine.. 4527.61 BogoMIPS (lpj=9055225)
[ 10.439423] Security Framework initialized
[ 10.439433] SELinux: Disabled at boot.
[ 10.439455] AppArmor: AppArmor initialized
[ 10.439463] Failure registering capabilities with primary security module.
[ 10.439477] Mount-cache hash table entries: 512
[ 10.439681] Initializing cgroup subsys ns
[ 10.439689] Initializing cgroup subsys cpuacct
[ 10.439709] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0008e3fd 00000000 00000001 00000000
[ 10.439722] monitor/mwait feature present.
[ 10.439726] using mwait in idle threads.
[ 10.439733] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 10.439738] CPU: L2 cache: 3072K
[ 10.439742] CPU: Physical Processor ID: 0
[ 10.439745] CPU: Processor Core ID: 0
[ 10.439749] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0008e3fd 00000000 00000001 00000000
[ 10.439766] Compat vDSO mapped to ffffe000.
[ 10.439789] Checking 'hlt' instruction... OK.
[ 10.456206] SMP alternatives: switching to UP code
[ 10.459840] Early unpacking initramfs... done
[ 11.241752] ACPI: Core revision 20070126
[ 11.241924] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 11.271538] CPU0: Intel(R) Core(TM)2 Duo CPU P8400 @ 2.26GHz stepping 06
[ 11.271567] SMP alternatives: switching to SMP code
[ 11.273183] Booting processor 1/1 eip 3000
[ 11.284137] Initializing CPU#1
[ 11.361541] Calibrating delay using timer specific routine.. 4522.08 BogoMIPS (lpj=9044171)
[ 11.361554] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0008e3fd 00000000 00000001 00000000
[ 11.361564] monitor/mwait feature present.
[ 11.361569] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 11.361573] CPU: L2 cache: 3072K
[ 11.361577] CPU: Physical Processor ID: 0
[ 11.361579] CPU: Processor Core ID: 1
[ 11.361582] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0008e3fd 00000000 00000001 00000000
[ 11.363051] CPU1: Intel(R) Core(TM)2 Duo CPU P8400 @ 2.26GHz stepping 06
[ 11.363089] Total of 2 processors activated (9049.69 BogoMIPS).
[ 11.363277] ENABLING IO-APIC IRQs
[ 11.363490] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 11.509434] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 11.529425] Brought up 2 CPUs
[ 11.529465] CPU0 attaching sched-domain:
[ 11.529469] domain 0: span 03
[ 11.529473] groups: 01 02
[ 11.529479] CPU1 attaching sched-domain:
[ 11.529482] domain 0: span 03
[ 11.529486] groups: 02 01
[ 11.529891] net_namespace: 64 bytes
[ 11.529904] Booting paravirtualized kernel on bare hardware
[ 11.530793] Time: 1:59:04 Date: 09/07/08
[ 11.530843] NET: Registered protocol family 16
[ 11.531211] EISA bus registered
[ 11.531219] ACPI: bus type pci registered
[ 11.532078] PCI: PCI BIOS revision 3.00 entry at 0xfddc7, last bus=24
[ 11.532083] PCI: Using configuration type 1
[ 11.532100] Setting up standard PCI resources
[ 11.537873] ACPI: EC: EC description table is found, configuring boot EC
[ 11.548221] ACPI: BIOS _OSI(Linux) query ignored
[ 11.548226] ACPI: DMI System Vendor: LENOVO
[ 11.548230] ACPI: DMI Product Name: 2764CTO
[ 11.548233] ACPI: DMI Product Version: ThinkPad T400
[ 11.548236] ACPI: DMI Board Name: 2764CTO
[ 11.548238] ACPI: DMI BIOS Vendor: LENOVO
[ 11.548241] ACPI: DMI BIOS Date: 08/19/2008
[ 11.548244] ACPI: Please send DMI info above to linux-acpi at vger.kernel.org
[ 11.548249] ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi at vger.kernel.org
[ 11.548573] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 11.628037] ACPI: Interpreter enabled
[ 11.628042] ACPI: (supports S0 S3 S4 S5)
[ 11.628076] ACPI: Using IOAPIC for interrupt routing
[ 11.704381] ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
[ 11.704387] ACPI: EC: driver started in poll mode
[ 11.704751] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 11.707710] PCI: Transparent bridge - 0000:00:1e.0
[ 11.707859] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 11.708307] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
[ 11.708589] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 11.708885] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 11.709173] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 11.709461] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 11.717506] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.717962] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.718414] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.718865] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.719316] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.719767] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.720218] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.720669] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 11.721007] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 11.721161] ACPI: Power Resource [PUBS] (on)
[ 11.721296] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 11.721354] pnp: PnP ACPI init
[ 11.721369] ACPI: bus type pnp registered
[ 11.744401] pnpacpi: exceeded the max number of mem resources: 12
[ 11.788706] pnp: PnP ACPI: found 10 devices
[ 11.788712] ACPI: ACPI bus type pnp unregistered
[ 11.788717] PnPBIOS: Disabled by ACPI PNP
[ 11.789207] PCI: Using ACPI for IRQ routing
[ 11.789213] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 12.028224] NET: Registered protocol family 8
[ 12.028228] NET: Registered protocol family 20
[ 12.028290] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 12.028299] hpet0: 4 64-bit timers, 14318180 Hz
[ 12.029357] AppArmor: AppArmor Filesystem Enabled
[ 12.032204] Time: tsc clocksource has been installed.
[ 12.032223] Switched to high resolution mode on CPU 0
[ 12.032407] Switched to high resolution mode on CPU 1
[ 12.048170] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 12.048176] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 12.048182] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 12.048187] system 00:00: iomem range 0xc8000-0xcbfff has been reserved
[ 12.048192] system 00:00: iomem range 0xcc000-0xcffff has been reserved
[ 12.048198] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved
[ 12.048203] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 12.048208] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 12.048213] system 00:00: iomem range 0xdc000-0xdffff has been reserved
[ 12.048219] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[ 12.048224] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[ 12.048229] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[ 12.048242] system 00:02: ioport range 0x164e-0x164f has been reserved
[ 12.048248] system 00:02: ioport range 0x1000-0x107f has been reserved
[ 12.048253] system 00:02: ioport range 0x1180-0x11ff has been reserved
[ 12.048258] system 00:02: ioport range 0x800-0x80f has been reserved
[ 12.048264] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[ 12.048269] system 00:02: ioport range 0x1600-0x1641 has been reserved
[ 12.048274] system 00:02: ioport range 0x1600-0x161b has been reserved
[ 12.048281] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 12.048287] system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved
[ 12.048293] system 00:02: iomem range 0xfed10000-0xfed13fff could not be reserved
[ 12.048299] system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 12.048305] system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved
[ 12.048311] system 00:02: iomem range 0xfed45000-0xfed4bfff could not be reserved
[ 12.079081] PCI: Bridge: 0000:00:1c.0
[ 12.079085] IO window: disabled.
[ 12.079093] MEM window: disabled.
[ 12.079099] PREFETCH window: disabled.
[ 12.079107] PCI: Bridge: 0000:00:1c.1
[ 12.079110] IO window: disabled.
[ 12.079118] MEM window: f4300000-f43fffff
[ 12.079124] PREFETCH window: disabled.
[ 12.079132] PCI: Bridge: 0000:00:1c.3
[ 12.079137] IO window: 2000-2fff
[ 12.079145] MEM window: f8000000-f9ffffff
[ 12.079152] PREFETCH window: f4000000-f40fffff
[ 12.079160] PCI: Bridge: 0000:00:1c.4
[ 12.079165] IO window: 3000-3fff
[ 12.079173] MEM window: fa000000-fbffffff
[ 12.079180] PREFETCH window: f4100000-f41fffff
[ 12.079195] PCI: Bus 22, cardbus bridge: 0000:15:00.0
[ 12.079198] IO window: 00004000-000040ff
[ 12.079206] IO window: 00004400-000044ff
[ 12.079213] PREFETCH window: f0000000-f3ffffff
[ 12.079221] MEM window: c0000000-c3ffffff
[ 12.079228] PCI: Bridge: 0000:00:1e.0
[ 12.079233] IO window: 4000-7fff
[ 12.079241] MEM window: f4800000-f7ffffff
[ 12.079248] PREFETCH window: f0000000-f3ffffff
[ 12.079290] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 12.079301] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 12.079334] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17
[ 12.079343] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 12.079376] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 18
[ 12.079386] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 12.079417] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 20 (level, low) -> IRQ 16
[ 12.079426] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 12.079446] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 12.079470] ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 19
[ 12.079495] NET: Registered protocol family 2
[ 12.116075] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 12.116508] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 12.117336] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 12.117712] TCP: Hash tables configured (established 131072 bind 65536)
[ 12.117717] TCP reno registered
[ 12.128161] checking if image is initramfs... it is
[ 13.662416] Freeing initrd memory: 7911k freed
[ 13.662635] Simple Boot Flag at 0x35 set to 0x1
[ 13.663800] audit: initializing netlink socket (disabled)
[ 13.663821] audit(1220752744.921:1): initialized
[ 13.664223] highmem bounce pool size: 64 pages
[ 13.668060] VFS: Disk quotas dquot_6.5.1
[ 13.668200] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 13.668435] io scheduler noop registered
[ 13.668439] io scheduler anticipatory registered
[ 13.668443] io scheduler deadline registered
[ 13.668465] io scheduler cfq registered (default)
[ 13.668484] Boot video device is 0000:00:02.0
[ 13.668882] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 13.668958] assign_interrupt_mode Found MSI capability
[ 13.669023] Allocate Port Service[0000:00:1c.0:pcie00]
[ 13.669089] Allocate Port Service[0000:00:1c.0:pcie02]
[ 13.669239] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 13.669313] assign_interrupt_mode Found MSI capability
[ 13.669374] Allocate Port Service[0000:00:1c.1:pcie00]
[ 13.669435] Allocate Port Service[0000:00:1c.1:pcie02]
[ 13.669584] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 13.669659] assign_interrupt_mode Found MSI capability
[ 13.669720] Allocate Port Service[0000:00:1c.3:pcie00]
[ 13.669780] Allocate Port Service[0000:00:1c.3:pcie02]
[ 13.669941] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 13.670016] assign_interrupt_mode Found MSI capability
[ 13.670076] Allocate Port Service[0000:00:1c.4:pcie00]
[ 13.670142] Allocate Port Service[0000:00:1c.4:pcie02]
[ 13.670588] isapnp: Scanning for PnP cards...
[ 14.024522] isapnp: No Plug & Play device found
[ 14.075010] Real Time Clock Driver v1.12ac
[ 14.075178] hpet_resources: 0xfed00000 is busy
[ 14.075253] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 14.077784] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 14.077907] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 14.078088] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 14.086527] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 14.086537] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 14.105108] mice: PS/2 mouse device common for all mice
[ 14.105318] EISA: Probing bus 0 at eisa.0
[ 14.105327] Cannot allocate resource for EISA slot 1
[ 14.105333] Cannot allocate resource for EISA slot 2
[ 14.105337] Cannot allocate resource for EISA slot 3
[ 14.105341] Cannot allocate resource for EISA slot 4
[ 14.105345] Cannot allocate resource for EISA slot 5
[ 14.105349] Cannot allocate resource for EISA slot 6
[ 14.105353] Cannot allocate resource for EISA slot 7
[ 14.105362] EISA: Detected 0 cards.
[ 14.105368] cpuidle: using governor ladder
[ 14.105371] cpuidle: using governor menu
[ 14.105509] NET: Registered protocol family 1
[ 14.105557] Using IPI No-Shortcut mode
[ 14.105600] registered taskstats version 1
[ 14.105813] Magic number: 8:89:963
[ 14.105822] hash matches device ttyb4
[ 14.105886] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 14.105890] EDD information not available.
[ 14.106200] Freeing unused kernel memory: 368k freed
[ 14.109678] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 15.525849] fuse init (API version 7.9)
[ 15.570344] ACPI: SSDT BC6D6C20, 02C8 (r1 PmRef Cpu0Ist 3000 INTL 20050624)
[ 15.570962] ACPI: SSDT BC6D4020, 087A (r1 PmRef Cpu0Cst 3001 INTL 20050624)
[ 15.576767] Monitor-Mwait will be used to enter C-1 state
[ 15.576774] Monitor-Mwait will be used to enter C-2 state
[ 15.576779] Monitor-Mwait will be used to enter C-3 state
[ 15.577075] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 15.577085] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 15.577855] ACPI: SSDT BC6D5CA0, 01CF (r1 PmRef ApIst 3000 INTL 20050624)
[ 15.578599] ACPI: SSDT BC6D5F20, 008D (r1 PmRef ApCst 3000 INTL 20050624)
[ 15.582760] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 15.582770] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 15.582800] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 15.582821] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 15.586814] ACPI: Thermal Zone [THM0] (39 C)
[ 15.589995] ACPI: Thermal Zone [THM1] (30 C)
[ 15.625052] device-mapper: uevent: version 1.0.3
[ 15.625162] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel at redhat.com
[ 15.964306] usbcore: registered new interface driver usbfs
[ 15.964349] usbcore: registered new interface driver hub
[ 15.976187] usbcore: registered new device driver usb
[ 15.988203] USB Universal Host Controller Interface driver v3.0
[ 15.988292] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 15.988309] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 15.988317] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 15.988648] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 15.988692] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001860
[ 15.988938] usb usb1: configuration #1 chosen from 1 choice
[ 15.988983] hub 1-0:1.0: USB hub found
[ 15.988993] hub 1-0:1.0: 2 ports detected
[ 16.092075] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 17
[ 16.092094] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 16.092102] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 16.092143] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 16.092185] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00001880
[ 16.092396] usb usb2: configuration #1 chosen from 1 choice
[ 16.092441] hub 2-0:1.0: USB hub found
[ 16.092451] hub 2-0:1.0: 2 ports detected
[ 16.195891] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 22 (level, low) -> IRQ 20
[ 16.195909] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 16.195917] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 16.195959] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 16.195999] uhci_hcd 0000:00:1a.2: irq 20, io base 0x000018a0
[ 16.196209] usb usb3: configuration #1 chosen from 1 choice
[ 16.196255] hub 3-0:1.0: USB hub found
[ 16.196265] hub 3-0:1.0: 2 ports detected
[ 16.299658] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19
[ 16.299677] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 16.299685] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 16.299732] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 16.299775] uhci_hcd 0000:00:1d.0: irq 19, io base 0x000018c0
[ 16.299996] usb usb4: configuration #1 chosen from 1 choice
[ 16.300043] hub 4-0:1.0: USB hub found
[ 16.300053] hub 4-0:1.0: 2 ports detected
[ 16.403449] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 21
[ 16.403468] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 16.403476] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 16.403524] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 16.403565] uhci_hcd 0000:00:1d.1: irq 21, io base 0x000018e0
[ 16.403778] usb usb5: configuration #1 chosen from 1 choice
[ 16.403825] hub 5-0:1.0: USB hub found
[ 16.403835] hub 5-0:1.0: 2 ports detected
[ 16.435234] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 16.507276] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
[ 16.507296] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 16.507304] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 16.507349] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 16.507389] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001c00
[ 16.507602] usb usb6: configuration #1 chosen from 1 choice
[ 16.507651] hub 6-0:1.0: USB hub found
[ 16.507662] hub 6-0:1.0: 2 ports detected
[ 16.597414] usb 2-2: configuration #1 chosen from 1 choice
[ 16.611442] ACPI: PCI Interrupt 0000:00:1a.7[D] -> GSI 23 (level, low) -> IRQ 18
[ 16.611465] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 16.611472] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 16.611534] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
[ 16.615445] ehci_hcd 0000:00:1a.7: debug port 1
[ 16.615455] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 16.615473] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfc226c00
[ 16.631824] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 16.632019] usb usb7: configuration #1 chosen from 1 choice
[ 16.632068] hub 7-0:1.0: USB hub found
[ 16.632078] hub 7-0:1.0: 6 ports detected
[ 16.733114] SCSI subsystem initialized
[ 16.736116] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 23
[ 16.736138] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 16.736145] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 16.736200] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 16.740133] ehci_hcd 0000:00:1d.7: debug port 1
[ 16.740143] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 16.740158] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc227000
[ 16.755574] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 16.755768] usb usb8: configuration #1 chosen from 1 choice
[ 16.755817] hub 8-0:1.0: USB hub found
[ 16.755827] hub 8-0:1.0: 6 ports detected
[ 16.801176] libata version 3.00 loaded.
[ 16.859713] ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) -> IRQ 21
[ 16.912406] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[f4801000-f48017ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 16.917732] ahci 0000:00:1f.2: version 3.0
[ 16.917770] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 19
[ 16.917833] ahci 0000:00:1f.2: nr_ports (4) and implemented port map (0x3) don't match, using nr_ports
[ 16.917839] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
[ 17.027096] usb 2-2: USB disconnect, address 2
[ 17.266579] usb 2-2: new full speed USB device using uhci_hcd and address 3
[ 17.436774] usb 2-2: configuration #1 chosen from 1 choice
[ 17.917289] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 17.917299] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part
[ 17.917309] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 17.917833] scsi0 : ahci
[ 17.918241] scsi1 : ahci
[ 17.918553] scsi2 : ahci
[ 17.918834] scsi3 : ahci
[ 17.920611] ata1: SATA max UDMA/133 abar m2048 at 0xfc226000 port 0xfc226100 irq 219
[ 17.920618] ata2: SATA max UDMA/133 abar m2048 at 0xfc226000 port 0xfc226180 irq 219
[ 17.920624] ata3: SATA max UDMA/133 abar m2048 at 0xfc226000 port 0xfc226200 irq 219
[ 17.920629] ata4: SATA max UDMA/133 abar m2048 at 0xfc226000 port 0xfc226280 irq 219
[ 18.185468] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00061b032a2f8c15]
[ 18.231616] Clocksource tsc unstable (delta = -19337252550 ns)
[ 18.235700] Time: hpet clocksource has been installed.
[ 18.256351] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 18.256826] ata1.00: ATA-8: HITACHI HTS722016K9SA00, DCDZC75A, max UDMA/133
[ 18.256834] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 18.257603] ata1.00: configured for UDMA/133
[ 18.307144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 18.325927] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE MU10N, 1.05, max UDMA/33
[ 18.339787] ata2.00: configured for UDMA/33
[ 18.373737] ata3: SATA link down (SStatus 0 SControl 0)
[ 18.413413] ata4: SATA link down (SStatus 0 SControl 0)
[ 18.413724] scsi 0:0:0:0: Direct-Access ATA HITACHI HTS72201 DCDZ PQ: 0 ANSI: 5
[ 18.415407] scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD MU10N 1.05 PQ: 0 ANSI: 5
[ 18.439317] Driver 'sd' needs updating - please use bus_type methods
[ 18.439449] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 18.439472] sd 0:0:0:0: [sda] Write Protect is off
[ 18.439477] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 18.439509] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 18.439592] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 18.439613] sd 0:0:0:0: [sda] Write Protect is off
[ 18.439618] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 18.439651] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 18.439657] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 18.492532] sda1 sda2 sda3 < sda5 sda6 >
[ 18.501693] sd 0:0:0:0: [sda] Attached SCSI disk
[ 18.511859] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 18.511898] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 18.521885] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 18.521893] Uniform CD-ROM driver Revision: 3.20
[ 18.521983] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 18.968072] Attempting manual resume
[ 18.968079] swsusp: Resume From Partition 254:1
[ 18.968082] PM: Checking swsusp image.
[ 18.968334] PM: Resume from disk failed.
[ 18.998663] kjournald starting. Commit interval 5 seconds
[ 18.998684] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.319047] Linux agpgart interface v0.102
[ 22.405483] agpgart: Detected an Intel Intel Integrated Graphics Device Chipset.
[ 22.409662] agpgart: Detected 32252K stolen memory.
[ 22.542592] e1000e-ich9m: Intel(R) PRO/1000 Network Driver - 0.2.9.5
[ 22.542599] e1000e-ich9m: Copyright (c) 1999-2008 Intel Corporation.
[ 22.590446] agpgart: AGP aperture is 256M @ 0xd0000000
[ 22.591199] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 22.591219] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 22.712887] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:21:86:61:30:eb
[ 22.712894] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 22.712930] 0000:00:19.0: eth0: MAC: 5, PHY: 8, PBA No: 1008ff-0ff
[ 22.794113] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 22.862240] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 23.689484] input: Power Button (FF) as /devices/virtual/input/input2
[ 23.713135] ACPI: Power Button (FF) [PWRF]
[ 23.713260] input: Lid Switch as /devices/virtual/input/input3
[ 23.713588] ACPI: Lid Switch [LID]
[ 23.713728] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 23.732048] ACPI: Sleep Button (CM) [SLPB]
[ 24.316076] ACPI: WMI-Acer: Mapper loaded
[ 24.697020] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 24.719071] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 24.722204] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:07/LNXVIDEO:01/input/input6
[ 24.754974] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 24.940079] ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 21
[ 24.940115] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 25.009014] ath_hal: module license 'Proprietary' taints kernel.
[ 25.042486] ath_hal: 0.10.5.6 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417)
[ 25.190130] wlan: svn r3698
[ 25.332839] ath_pci: svn r3698
[ 25.333029] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 21
[ 25.333048] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 25.823519] MadWifi: ath_attach: HAL managed transmit power control (TPC) disabled.
[ 25.823545] MadWifi: ath_attach: Interference mitigation is supported. Currently disabled.
[ 25.910460] ACPI: AC Adapter [AC] (off-line)
[ 25.991931] ACPI: Battery Slot [BAT0] (battery present)
[ 26.560209] Bluetooth: Core ver 2.11
[ 26.578403] NET: Registered protocol family 31
[ 26.578408] Bluetooth: HCI device and connection manager initialized
[ 26.578415] Bluetooth: HCI socket layer initialized
[ 26.622265] Bluetooth: HCI USB driver ver 2.9
[ 26.623927] usbcore: registered new interface driver hci_usb
[ 27.332933] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 27.727802] MadWifi: ath_attach: Switching rfkill capability off.
[ 27.795861] ath_rate_sample: 1.2 (svn r3698)
[ 27.797309] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 27.797320] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 27.797338] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 27.797347] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, Radio 10.2)
[ 27.797357] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 27.797361] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 27.797365] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 27.797369] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 27.797372] wifi0: Use hw queue 4 for XR traffic
[ 27.797376] wifi0: Use hw queue 7 for UAPSD traffic
[ 27.797380] wifi0: Use hw queue 8 for CAB traffic
[ 27.797383] wifi0: Use hw queue 9 for beacons
[ 27.812134] Non-volatile memory driver v1.2
[ 27.851039] ath_pci: wifi0: Atheros 5424/2424: mem=0xf4300000, irq=21
[ 27.851098] Yenta: CardBus bridge found at 0000:15:00.0 [17aa:20c6]
[ 27.977251] Yenta: ISA IRQ mask 0x0cb8, PCI irq 19
[ 27.977258] Socket status: 30000006
[ 27.977263] pcmcia: parent PCI bridge I/O window: 0x4000 - 0x7fff
[ 27.977268] cs: IO port probe 0x4000-0x7fff: clean.
[ 27.979399] pcmcia: parent PCI bridge Memory window: 0xf4800000 - 0xf7ffffff
[ 27.979404] pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf3ffffff
[ 28.297779] Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1c0b1, caps: 0xd04791/0xb00000
[ 28.297791] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 28.339270] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[ 28.390215] thinkpad_acpi: ThinkPad ACPI Extras v0.17
[ 28.390220] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 28.390224] thinkpad_acpi: ThinkPad BIOS 7UET43WW (1.13 ), EC 7VHT12WW-1.01
[ 28.390228] thinkpad_acpi: Lenovo ThinkPad T400
[ 28.390833] thinkpad_acpi: radio switch found; radios are enabled
[ 28.399727] thinkpad_acpi: standard ACPI backlight interface available, not loading native one...
[ 28.400176] input: ThinkPad Extra Buttons as /devices/virtual/input/input9
[ 29.860364] cs: IO port probe 0x100-0x3af: clean.
[ 29.862635] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 29.863634] cs: IO port probe 0x820-0x8ff: clean.
[ 29.864427] cs: IO port probe 0xc00-0xcf7: clean.
[ 29.865498] cs: IO port probe 0xa00-0xaff: clean.
[ 30.009920] loop: module loaded
[ 30.091379] lp: driver loaded but no devices found
[ 30.357025] Adding 4194296k swap on /dev/mapper/sys-swap. Priority:-1 extents:1 across:4194296k
[ 30.416903] EXT3 FS on dm-0, internal journal
[ 30.586262] kjournald starting. Commit interval 5 seconds
[ 30.587542] EXT3 FS on sda2, internal journal
[ 30.587556] EXT3-fs: mounted filesystem with ordered data mode.
[ 30.599247] kjournald starting. Commit interval 5 seconds
[ 30.599548] EXT3 FS on dm-3, internal journal
[ 30.599560] EXT3-fs: mounted filesystem with ordered data mode.
[ 30.606631] kjournald starting. Commit interval 5 seconds
[ 30.608631] EXT3 FS on dm-4, internal journal
[ 30.608642] EXT3-fs: mounted filesystem with ordered data mode.
[ 30.615583] kjournald starting. Commit interval 5 seconds
[ 30.615937] EXT3 FS on dm-2, internal journal
[ 30.615948] EXT3-fs: mounted filesystem with ordered data mode.
[ 31.522261] ip_tables: (C) 2000-2006 Netfilter Core Team
More information about the freebsd-mobile
mailing list