[Wireless] Can't connect to wlan
Mel
fbsd.questions at rachie.is-a-geek.net
Sun Feb 24 16:47:01 UTC 2008
Redirect -> freebsd-mobile, cc Ben
Ref:
http://lists.freebsd.org/pipermail/freebsd-current/2007-November/080653.html
On Sunday 24 February 2008 16:50:47 Alphons "Fonz" van Werven wrote:
> Okay, so here goes:
>
> SYNOPSIS
>
> Wireless network gets detected, but has "no carrier". So I can't connect.
>
> PROMPT
>
> All prompts are indicated as $ to avoid confusion with #-comment lines, but
> in reality most things are done by root.
>
> THE NETWORK
>
> SSID: SpeedTouch1EC5E8
> radio type: 11g
> security type: WPA2-PSK
> PSK: known
> Station: Thomson ST 780 WL Wireless modem
> Signal: present (Windows picks it up right away) and generally excellent
>
> THE COMPUTER
>
> Thoshiba Satellite P200 1A4 notebook
> Wireless card: Intel 3945ABG
> OS: FreeBSD 7.0-RC3
>
> KERNEL
>
> The driver for the Intel 3945ABG card is wpi.
> As instructed by its manpage, my /boot/loader.conf reads:
>
> $ cat /boot/loader.conf
> if_wpi_load="YES"
> wlan_load="YES"
> wlan_amrr_load="YES"
> firmware_load="YES"
> wpifw_load="YES"
> wlan_xauth_load="YES"
>
> legal.intel_wpi.license_ack=1
> $
>
> Relevant dmesg greps:
>
> $ dmesg|grep wpi
> wpi0: <Intel(R) PRO/Wireless 3945ABG> mem 0xd8000000-0xd8000fff irq 17 at
> device 0.0 on pci4
> wpi0: Ethernet address: 00:1b:77:b5:98:bd
> wpi0: [ITHREAD]
> wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
> wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
> 24Mbps 36Mbps 48Mbps 54Mbps
> $ dmesg|grep wlan
> $ dmesg|grep firmware
> $
>
> CONFIGURATION
>
> My /etc/wpa_supplicant.conf:
As you can see in the aboved mentioned URL, wpi and wpa_supplicant don't play
nice. I had the same problem yesterday, setting wpi through ifconfig (WEP in
my case) and the card just works.
I also had the bluetooth message, but Fonz doesn't seem to have that.
# ident /boot/kernel/if_wpi.ko
/boot/kernel/if_wpi.ko:
$FreeBSD: src/sys/dev/wpi/if_wpi.c,v 1.5.2.2 2008/02/02 06:49:57 sam Exp
$
My kernel is GENERIC with ULE scheduler rather then 4BSD. I want to
investigate more this week, with a debug kernel and/or wpi in debug mode.
Since RELENG_7 is probably thawed/frozen, is there patches from -current you
can backport to have tested?
Leaving the rest of the email in tact so you have a full report.
> $ cat /etc/wpa_supplicant.conf
> #eapol_version=2
>
> network={
> ssid="SpeedTouch1EC5E8"
> psk="********" (the correct preshared key, that is)
> # bssid=00:90:d0:f3:e1:d2
> mode=0
> proto=WPA RSN
> # key_mgmt=WPA-PSK
> # pairwise=CCMP
> # group=CCMP
> scan_ssid=1
> }
> $
>
> STEPS
>
> $ wpa_supplicant -d -i wpi0 -c /etc/wpa_supplicant
> Initializing interface 'wpi0' conf '/etc/wpa_supplicant.conf' driver
> 'default' ctrl_interface 'N/A' bridge 'N/A'
> Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
> Reading configuration file '/etc/wpa_supplicant.conf'
> Priority group 0
> id=0 ssid='SpeedTouch1EC5E8'
> Initializing interface (2) 'wpi0'
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> EAPOL: SUPP_BE entering state INITIALIZE
> EAP: EAP entering state DISABLED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> Own MAC address: 00:1b:77:b5:98:bd
> wpa_driver_bsd_set_wpa: enabled=1
> wpa_driver_bsd_set_wpa_internal: wpa=3 privacy=1
> wpa_driver_bsd_del_key: keyidx=0
> wpa_driver_bsd_del_key: keyidx=1
> wpa_driver_bsd_del_key: keyidx=2
> wpa_driver_bsd_del_key: keyidx=3
> wpa_driver_bsd_set_countermeasures: enabled=0
> wpa_driver_bsd_set_drop_unencrypted: enabled=1
> Setting scan request: 0 sec 100000 usec
> Added interface wpi0
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> State: DISCONNECTED -> SCANNING
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Trying to get current scan results first without requesting a new scan to
> speed up initial association
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 0 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> Try to find non-WPA AP
> No suitable AP found.
> Setting scan request: 5 sec 0 usec
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (1 BSSes)
> Scan results: 1
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> 0: 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8' wpa_ie_len=30 rsn_ie_len=26
> caps=0x11
> selected based on RSN IE
> selected WPA AP 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8'
> Try to find non-WPA AP
> Trying to associate with 00:90:d0:f3:e1:d2 (SSID='SpeedTouch1EC5E8'
> freq=2437 MHz)
> Cancelling scan request
> WPA: clearing own WPA/RSN IE
> Automatic auth_alg selection: 0x1
> wpa_driver_bsd_set_auth_alg alg 0x1 authmode 1
> RSN: using IEEE 802.11i/D9.0
> WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
> WPA: set AP WPA IE - hexdump(len=30): dd 1c 00 50 f2 01 01 00 00 50 f2 02
> 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2 02 0c 00
> WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f
> ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00
> WPA: using GTK TKIP
> WPA: using PTK CCMP
> WPA: using KEY_MGMT WPA-PSK
> WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01
> 00 00 0f ac 04 01 00 00 0f ac 02 00 00
> No keys have been configured - skip key clearing
> wpa_driver_bsd_set_drop_unencrypted: enabled=1
> State: SCANNING -> ASSOCIATING
> wpa_driver_bsd_associate: ssid 'SpeedTouch1EC5E8' wpa ie len 22 pairwise 3
> group 2 key mgmt 1
> wpa_driver_bsd_associate: set PRIVACY 1
> Setting authentication timeout: 10 sec 0 usec
> EAPOL: External notification - EAP success=0
> EAPOL: External notification - EAP fail=0
> EAPOL: External notification - portControl=Auto
> RSN: Ignored PMKID candidate without preauth flag
> Authentication with 00:00:00:00:00:00 timed out.
> Added BSSID 00:90:d0:f3:e1:d2 into blacklist
> No keys have been configured - skip key clearing
> State: ASSOCIATING -> DISCONNECTED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> EAPOL: External notification - EAP success=0
> Setting scan request: 0 sec 0 usec
> State: DISCONNECTED -> SCANNING
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=16):
> 53 70 65 65 64 54 6f 75 63 68 31 45 43 35 45 38 SpeedTouch1EC5E8
> Received 0 bytes of scan results (1 BSSes)
> Scan results: 1
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> 0: 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8' wpa_ie_len=30 rsn_ie_len=26
> caps=0x11
> selected based on RSN IE
> selected WPA AP 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8'
> Try to find non-WPA AP
> Trying to associate with 00:90:d0:f3:e1:d2 (SSID='SpeedTouch1EC5E8'
> freq=2437 MHz)
> Cancelling scan request
> WPA: clearing own WPA/RSN IE
> Automatic auth_alg selection: 0x1
> wpa_driver_bsd_set_auth_alg alg 0x1 authmode 1
> RSN: using IEEE 802.11i/D9.0
> WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
> WPA: set AP WPA IE - hexdump(len=30): dd 1c 00 50 f2 01 01 00 00 50 f2 02
> 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2 02 0c 00
> WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f
> ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00
> WPA: using GTK TKIP
> WPA: using PTK CCMP
> WPA: using KEY_MGMT WPA-PSK
> WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01
> 00 00 0f ac 04 01 00 00 0f ac 02 00 00
> No keys have been configured - skip key clearing
> wpa_driver_bsd_set_drop_unencrypted: enabled=1
> State: SCANNING -> ASSOCIATING
> wpa_driver_bsd_associate: ssid 'SpeedTouch1EC5E8' wpa ie len 22 pairwise 3
> group 2 key mgmt 1
> wpa_driver_bsd_associate: set PRIVACY 1
> Setting authentication timeout: 10 sec 0 usec
> EAPOL: External notification - EAP success=0
> EAPOL: External notification - EAP fail=0
> EAPOL: External notification - portControl=Auto
> RSN: Ignored PMKID candidate without preauth flag
> Authentication with 00:00:00:00:00:00 timed out.
> BSSID 00:90:d0:f3:e1:d2 blacklist count incremented to 2
> No keys have been configured - skip key clearing
> State: ASSOCIATING -> DISCONNECTED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> EAPOL: External notification - EAP success=0
> Setting scan request: 0 sec 0 usec
> State: DISCONNECTED -> SCANNING
> Starting AP scan (broadcast SSID)
> Received 0 bytes of scan results (1 BSSes)
> Scan results: 1
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> 0: 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8' wpa_ie_len=30 rsn_ie_len=26
> caps=0x11
> skip - blacklisted
> Try to find non-WPA AP
> 0: 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8' wpa_ie_len=30 rsn_ie_len=26
> caps=0x11
> skip - blacklisted
> No APs found - clear blacklist and try again
> Removed BSSID 00:90:d0:f3:e1:d2 from blacklist (clear)
> Selecting BSS from priority group 0
> Try to find WPA-enabled AP
> 0: 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8' wpa_ie_len=30 rsn_ie_len=26
> caps=0x11
> selected based on RSN IE
> selected WPA AP 00:90:d0:f3:e1:d2 ssid='SpeedTouch1EC5E8'
> Try to find non-WPA AP
> Trying to associate with 00:90:d0:f3:e1:d2 (SSID='SpeedTouch1EC5E8'
> freq=2437 MHz)
> Cancelling scan request
> WPA: clearing own WPA/RSN IE
> Automatic auth_alg selection: 0x1
> wpa_driver_bsd_set_auth_alg alg 0x1 authmode 1
> RSN: using IEEE 802.11i/D9.0
> WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2
> WPA: set AP WPA IE - hexdump(len=30): dd 1c 00 50 f2 01 01 00 00 50 f2 02
> 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2 02 0c 00
> WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00 00 0f ac 02 02 00 00 0f
> ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00
> WPA: using GTK TKIP
> WPA: using PTK CCMP
> WPA: using KEY_MGMT WPA-PSK
> WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 02 01
> 00 00 0f ac 04 01 00 00 0f ac 02 00 00
> No keys have been configured - skip key clearing
> wpa_driver_bsd_set_drop_unencrypted: enabled=1
> State: SCANNING -> ASSOCIATING
> wpa_driver_bsd_associate: ssid 'SpeedTouch1EC5E8' wpa ie len 22 pairwise 3
> group 2 key mgmt 1
> wpa_driver_bsd_associate: set PRIVACY 1
> Setting authentication timeout: 10 sec 0 usec
> EAPOL: External notification - EAP success=0
> EAPOL: External notification - EAP fail=0
> EAPOL: External notification - portControl=Auto
> RSN: Ignored PMKID candidate without preauth flag
>
> (after which it keeps repeating the above story until I stop it)
>
> CTRL-EVENT-TERMINATING - signal 2 received
> Removing interface wpi0
> State: ASSOCIATING -> DISCONNECTED
> No keys have been configured - skip key clearing
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> wpa_driver_bsd_set_wpa: enabled=0
> wpa_driver_bsd_set_wpa_internal: wpa=0 privacy=0
> wpa_driver_bsd_set_drop_unencrypted: enabled=0
> wpa_driver_bsd_set_countermeasures: enabled=0
> No keys have been configured - skip key clearing
> Cancelling scan request
> Cancelling authentication timeout
> wpa_driver_bsd_set_wpa_internal: wpa=0 privacy=1
> $
>
> After this:
>
> $ ifcondig wpi0
> wpi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
> ether 00:1b:77:b5:98:bd
> media: IEEE 802.11 Wireless Ethernet autoselect mode 11g (DS/1Mbps)
> status: no carrier
> ssid SpeedTouch1EC5E8 channel 6 (2437 Mhz 11g)
> authmode WPA2/802.11i privacy ON deftxkey UNDEF txpower 50 bmiss 7
> scanvalid 60 protmode CTS roaming MANUAL
> $
>
> As you can see, there's still no carrier, so
>
> $ dhclient wpi0
> wpi0: no link .............. giving up
> $
>
> If there's anything else you need to know, just holler.
>
> Thanks in advance,
>
> Alphons
--
Mel
More information about the freebsd-mobile
mailing list