iwi fatal error on Dell Inspiron 6000 (debug info attached)
Ted Faber
faber at isi.edu
Thu May 12 10:36:53 PDT 2005
Hi.
I'm getting a new Dell Inspiron 6000 (BIOS version A05) up and
configured and I've run into a problem under -CURRENT. I'm running
-CURRENT as of 13 May 05 with the iwi driver compiled in:
FreeBSD lap.isi.edu 6.0-CURRENT FreeBSD 6.0-CURRENT #0: Thu May 12 08:59:58 PDT 2005 root at lap.isi.edu:/usr/obj/usr/src/sys/LAP i386
and the iwicontol tool from http://damien.bergamini.free.fr/ipw/ version
iwi-freebsd-1.4.2.
I type this:
lap:~$ sudo sysctl net.wlan.debug=-1
Password:
net.wlan.debug: 0 -> -1
lap:~$ sudo sysctl net.wlan.0.debug=-1
net.wlan.0.debug: 0 -> -1
lap:~$ sudo iwicontrol -i iwi0 -d /usr/local/libdata/if_iwi -m bss
lap:~$ sudo iwicontrol -i iwi0 -r
Radio is ON
lap:~$ sudo ifconfig iwi0 inet 192.168.0.20 netmask 0xffffff00 ssid ISI-GUEST wepkey `cat /usr/local/etc/wepkey` weptxkey 1 wepmode on
And get the following on the console (in the logs):
ieee80211_crypto_setkey: WEP keyix 0 flags 0x3 mac 00:12:f0:49:06:96 rsc 0 tsc 0 len 13
begin active scan in auto mode, scangen 2
ieee80211_reset_scan: scan set: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 start chan 255
ieee80211_free_allnodes_locked: free all nodes in scan table
node_reclaim: remove 0xc1fad800<00:12:f0:49:06:96> from scan table, refcnt 1
ieee80211_next_scan: chan 255->1
iwi0: fatal error
Needless to say the wireless doesn't connect. Any ideas what's wrong?
I'm happy to help debug...
Attached are the dmesg from a boot -v and kernel config.
--
Ted Faber
http://www.isi.edu/~faber PGP: http://www.isi.edu/~faber/pubkeys.asc
Unexpected attachment on this mail? See http://www.isi.edu/~faber/FAQ.html#SIG
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #0: Thu May 12 08:59:58 PDT 2005
root at lap.isi.edu:/usr/obj/usr/src/sys/LAP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc07ce000.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc07ce1c4.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc07ce270.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc07ce31c.
Calibrating clock(s) ... i8254 clock: 1193183 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1995009906 Hz
CPU: Intel(R) Pentium(R) M processor 2.00GHz (1995.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8
Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
real memory = 1073557504 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000825000 - 0x000000003eda2fff, 1045946368 bytes (255358 pages)
avail memory = 1045917696 (997 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xbaae
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R > on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000054
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25908086)
pcibios: BIOS version 2.10
Found $PIR table, 9 entries at 0xc00fb7c0
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 3 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 3 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 3 0 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 3 1 A 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 3 1 B 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 3 1 C 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 3 3 A 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 3 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 9 10 11
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 9 10 11
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9 10 11
pci_link1: <ACPI PCI Link LNKB> irq 10 on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 5 7
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 7
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 7
pci_link2: <ACPI PCI Link LNKC> irq 9 on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 9 10 11
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 9 10 11
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 9 10 11
pci_link3: <ACPI PCI Link LNKD> irq 7 on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 7 N 0 5 7 9 10 11
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 7 N 0 5 7 9 10 11
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 5 7 9 10 11
pci_link4: <ACPI PCI Link LNKE> on acpi0
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: <ACPI PCI Link LNKF> on acpi0
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: <ACPI PCI Link LNKH> on acpi0
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x10e0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x2590, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2591, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
found-> vendor=0x8086, dev=0x2658, revid=0x03
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 0000bf80, size 5, enabled
pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 29 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found-> vendor=0x8086, dev=0x2659, revid=0x03
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
map[20]: type 4, range 32, base 0000bf60, size 5, enabled
pcib0: matched entry for 0.29.INTB (src \\_SB_.PCI0.LNKB:0)
pci_link1: Picked IRQ 9 with weight 0
pcib0: slot 29 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
found-> vendor=0x8086, dev=0x265a, revid=0x03
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=9
map[20]: type 4, range 32, base 0000bf40, size 5, enabled
pcib0: matched entry for 0.29.INTC (src \\_SB_.PCI0.LNKC:0)
pcib0: slot 29 INTC routed to irq 9 via \\_SB_.PCI0.LNKC
found-> vendor=0x8086, dev=0x265b, revid=0x03
bus=0, slot=29, func=3
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=7
map[20]: type 4, range 32, base 0000bf20, size 5, enabled
pcib0: matched entry for 0.29.INTD (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 29 INTD routed to irq 7 via \\_SB_.PCI0.LNKD
found-> vendor=0x8086, dev=0x265c, revid=0x03
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base ffa80800, size 10, enabled
pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 29 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found-> vendor=0x8086, dev=0x2448, revid=0xd3
bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=1
cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x266e, revid=0x03
bus=0, slot=30, func=2
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ed00, size 8, enabled
map[14]: type 4, range 32, base 0000ec40, size 6, enabled
map[18]: type 1, range 32, base dffffe00, size 9, enabled
map[1c]: type 1, range 32, base dffffd00, size 8, enabled
pcib0: matched entry for 0.30.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 30 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found-> vendor=0x8086, dev=0x266d, revid=0x03
bus=0, slot=30, func=3
class=07-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ee00, size 8, enabled
map[14]: type 4, range 32, base 0000ec80, size 7, enabled
pcib0: matched entry for 0.30.INTB (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 30 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
found-> vendor=0x8086, dev=0x2641, revid=0x03
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0107, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2653, revid=0x03
bus=0, slot=31, func=2
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000bfa0, size 4, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 31 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
found-> vendor=0x8086, dev=0x266a, revid=0x03
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0101, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
map[20]: type 4, range 32, base 000010c0, size 5, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 31 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xdfd00000-0xdfefffff
pcib1: prefetched decode 0xd0000000-0xd7ffffff
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1002, dev=0x5460, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 3, range 32, base d0000000, size 27, enabled
pcib1: (null) requested memory range 0xd0000000-0xd7ffffff: good
map[14]: type 4, range 32, base 0000de00, size 8, enabled
pcib1: (null) requested I/O range 0xde00-0xdeff: in range
map[18]: type 1, range 32, base dfdf0000, size 16, enabled
pcib1: (null) requested memory range 0xdfdf0000-0xdfdfffff: good
pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.LNKA:0)
pcib1: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbf80
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0xbf60-0xbf7f irq 9 at device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbf60
uhci1: [GIANT-LOCKED]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0xbf40-0xbf5f irq 9 at device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbf40
uhci2: [GIANT-LOCKED]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0xbf20-0xbf3f irq 7 at device 29.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbf20
uhci3: [GIANT-LOCKED]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xffa80800-0xffa80bff irq 11 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xffa80800
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2: secondary bus 3
pcib2: subordinate bus 4
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xdfc00000-0xdfcfffff
pcib2: prefetched decode 0xfff00000-0xfffff
pcib2: Subtractively decoded bridge.
pci3: <ACPI PCI bus> on pcib2
pci3: physical bus=3
found-> vendor=0x14e4, dev=0x170c, revid=0x02
bus=3, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dfcfe000, size 13, enabled
pcib2: (null) requested memory range 0xdfcfe000-0xdfcfffff: good
pcib2: matched entry for 3.0.INTA (src \\_SB_.PCI0.LNKC:0)
pcib2: slot 0 INTA routed to irq 9 via \\_SB_.PCI0.LNKC
found-> vendor=0x1180, dev=0x0476, revid=0xb3
bus=3, slot=1, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found-> vendor=0x1180, dev=0x0552, revid=0x08
bus=3, slot=1, func=1
class=0c-00-10, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns)
intpin=b, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dfcfc800, size 11, enabled
pcib2: (null) requested memory range 0xdfcfc800-0xdfcfcfff: good
pcib2: matched entry for 3.1.INTB (src \\_SB_.PCI0.LNKC:0)
pcib2: slot 1 INTB routed to irq 9 via \\_SB_.PCI0.LNKC
found-> vendor=0x1180, dev=0x0822, revid=0x17
bus=3, slot=1, func=2
class=08-05-01, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base dfcfc700, size 8, enabled
pcib2: (null) requested memory range 0xdfcfc700-0xdfcfc7ff: good
pcib2: matched entry for 3.1.INTC (src \\_SB_.PCI0.LNKB:0)
pcib2: slot 1 INTC routed to irq 9 via \\_SB_.PCI0.LNKB
found-> vendor=0x8086, dev=0x4223, revid=0x05
bus=3, slot=3, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0116, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base dfcfd000, size 12, enabled
pcib2: (null) requested memory range 0xdfcfd000-0xdfcfdfff: good
pcib2: matched entry for 3.3.INTA (src \\_SB_.PCI0.LNKB:0)
pcib2: slot 3 INTA routed to irq 9 via \\_SB_.PCI0.LNKB
pci3: <network, ethernet> at device 0.0 (no driver attached)
pci3:0:0: Transition from D0 to D3
cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci3
pcib2: cbb0 requested memory range 0xdfc00000-0xdfcfffff: good
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xdfc00000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: matched entry for 3.1.INTA (src \\_SB_.PCI0.LNKD:0)
pcib2: slot 1 INTA routed to irq 7 via \\_SB_.PCI0.LNKD
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x04761180 0x02100007 0x060700b3 0x00824000
0x10: 0xdfc00000 0x020000dc 0x20040403 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc
0x30: 0x00000000 0xfffffffc 0x00000000 0x07400107
0x40: 0x01881028 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x30a00001 0x00000000 0x04630463 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000008 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0xb2000000 0x00003000 0x00000000
0xc0: 0x01881028 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001
0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
fwohci0: <Ricoh R5C552> mem 0xdfcfc800-0xdfcfcfff irq 9 at device 1.1 on pci3
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xdfcfc800
fwohci0: [MPSAFE]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 35:4f:c0:00:0f:27:a8:e1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci3: <base peripheral> at device 1.2 (no driver attached)
iwi0: <Intel(R) PRO/Wireless 2915ABG> mem 0xdfcfd000-0xdfcfdfff irq 9 at device 3.0 on pci3
iwi0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdfcfd000
iwi0: bpf attached
iwi0: Ethernet address: 00:12:f0:49:06:96
iwi0: bpf attached
iwi0: bpf attached
iwi0: [MPSAFE]
iwi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
pcm0: <Intel ICH6 (82801FB)> port 0xed00-0xedff,0xec40-0xec7f mem 0xdffffe00-0xdfffffff,0xdffffd00-0xdffffdff irq 11 at device 30.2 on pci0
pcm0: Reserved 0x200 bytes for rid 0x18 type 3 at 0xdffffe00
pcm0: Reserved 0x100 bytes for rid 0x1c type 3 at 0xdffffd00
pcm0: [GIANT-LOCKED]
pcm0: <SigmaTel STAC9752/53 AC97 Codec (id = 0x83847652)>
pcm0: Codec features headphone, 20 bit DAC, 20 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features variable rate PCM, AMAP, reserved 5
pcm0: sndbuf_setmap 3e9c5000, 4000; 0xe4cd8000 -> 3e9c5000
pcm0: sndbuf_setmap 3e9a4000, 4000; 0xe4cdc000 -> 3e9a4000
pci0: <simple comms, generic modem> at device 30.3 (no driver attached)
pci0:30:3: Transition from D0 to D3
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 SATA150 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xbfa0-0xbfaf irq 9 at device 31.2 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xbfa0
atapci0: failed to enable memory mapping!
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=01 ostat0=80 ostat1=00
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x80 err=0xff lsb=0xff msb=0xff
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=01 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64,0x62,0x66 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x601 0x601 0x601 0x601
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x601 0x601 0x601 0x601
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1995009906 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: 57231MB <HTS726060M9AT00 MH4OA6EA> at ata0-master UDMA100
ad0: 117210240 sectors [116280C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acpi_cmbat0: battery initialization done, tried 1 times
acd0: <HL-DT-STDVD-ROM GDR8082N/0106> DVDROM drive at ata1 as master
acd0: read 1722KB/s (4134KB/s), 256KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
pcm0: measured ac97 link rate at 47998 Hz, will use 48000 Hz
(probe0:sbp0:0:0:0): error 22
(probe0:sbp0:0:0:0): Unretryable Error
(probe1:sbp0:0:1:0): error 22
(probe1:sbp0:0:1:0): Unretryable Error
(probe3:sbp0:0:3:0): error 22
(probe3:sbp0:0:3:0): Unretryable Error
(probe4:sbp0:0:4:0): error 22
(probe4:sbp0:0:4:0): Unretryable Error
(probe5:sbp0:0:5:0): error 22
(probe5:sbp0:0:5:0): Unretryable Error
(probe6:sbp0:0:6:0): error 22
(probe6:sbp0:0:6:0): Unretryable Error
(probe2:sbp0:0:2:0): error 22
(probe2:sbp0:0:2:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled, default to deny, logging disabled
pci0: driver added
found-> vendor=0x8086, dev=0x266d, revid=0x03
bus=0, slot=30, func=3
class=07-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=9
powerspec 2 supports D0 D3 current D3
pci0:30:3: reprobing on driver added
pci0:30:3: Transition from D3 to D0
pci0:30:3: Transition from D0 to D3
found-> vendor=0x8086, dev=0x266a, revid=0x03
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0101, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=9
pci0:31:3: reprobing on driver added
pci1: driver added
found-> vendor=0x1002, dev=0x5460, revid=0x00
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
pci1:0:0: reprobing on driver added
pci3: driver added
found-> vendor=0x14e4, dev=0x170c, revid=0x02
bus=3, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D3
pci3:0:0: reprobing on driver added
pci3:0:0: Transition from D3 to D0
bfe0: <Broadcom BCM4401-B0 Fast Ethernet> mem 0xdfcfe000-0xdfcfffff irq 9 at device 0.0 on pci3
bfe0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xdfcfe000
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: bpf attached
bfe0: Ethernet address: 00:11:43:79:36:82
bfe0: [MPSAFE]
found-> vendor=0x1180, dev=0x0822, revid=0x17
bus=3, slot=1, func=2
class=08-05-01, hdrtype=0x00, mfdev=1
cmdreg=0x0106, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
pci3:1:2: reprobing on driver added
nfslock: pseudo-device
Linux ELF exec handler installed
-------------- next part --------------
#
# LAP -- kernel configuration file for FreeBSD/i386 for lap.isi.edu
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.428 2005/03/31 20:21:42 scottl Exp $
machine i386
cpu I686_CPU
ident LAP
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.
makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
#options SCHED_ULE # ULE scheduler
options SCHED_4BSD # 4BSD scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
options INET6 # IPv6 communications protocols
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options ADAPTIVE_GIANT # Giant mutex is adaptive.
# Debugging for use in -current
options KDB # Enable kernel debugger support.
options DDB # Support DDB.
options GDB # Support remote GDB.
#options INVARIANTS # Enable calls of extra sanity checking
#options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS
#options WITNESS # Enable checks to detect deadlocks and cycles
#options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed
# Bus support. Do not remove isa, even if you have no isa slots
device isa
device eisa
device pci
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
options ATA_STATIC_ID # Static device numbering
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device da # Direct Access (disks)
device pass # Passthrough device (direct SCSI access)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
device sc
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx
# Power management support (see NOTES for more options)
device apm
# Add suspend/resume support for the i8254.
device pmtimer
# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus
device cardbus # CardBus (32-bit) bus
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device ppi # Parallel port interface device
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
#device miibus # MII bus support
#device bfe # Broadcom BCM440x 10/100 Ethernet
# Wireless NIC cards
device wlan # 802.11 support
device wlan_wep # WEP crypto
device an # Aironet 4500/4800 802.11 wireless NICs.
device iwi # BayStack 660 and others
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
# Pseudo devices.
device loop # Network loopback
device mem # Memory and kernel memory devices
device io # I/O device
device random # Entropy device
device ether # Ethernet support
device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Note that 'bpf' is required for DHCP.
device bpf # Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device ehci # EHCI PCI->USB interface (USB 2.0)
device usb # USB Bus (required)
device ugen # Generic
device umass # Disks/Mass storage - Requires scbus and da
# FireWire support
device firewire # FireWire bus code
device sbp # SCSI over FireWire (Requires scbus and da)
# device fwe # Ethernet over FireWire (non-standard!)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 187 bytes
Desc: not available
Url : http://lists.freebsd.org/pipermail/freebsd-mobile/attachments/20050512/a9cf90b1/attachment.bin
More information about the freebsd-mobile
mailing list