acpi_perf error, powerd exiting

[Stefan Farfeleder]

Hi,

on my ThinkPad R32 (dmesg attached), acpi_perf reports the following
error at times, usually after a period of inactivity:

acpi_perf0: Px transition to 1200 failed
acpi_perf0: set freq failed, err 6

This causes powerd to terminate.  It seems to be a temporary error,
because if I restart powerd, it works again.  Should powerd be more
fault-tolerant, is this an acpi_perf bug or my hardware broken?

I've also attached sysctl dev.cpu and hw.acpi.

Stefan
-------------- next part --------------
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=\_PR_.CPU_
dev.cpu.0.%pnpinfo: _HID=none _UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.freq: 2000
dev.cpu.0.freq_levels: 2000/0 1750/0 1500/0 1250/0 1200/0 1050/0 1000/0 900/0 750/0 600/0 500/0 450/0 300/0 250/0 150/0
hw.acpi.supported_sleep_state: S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S3
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 0
hw.acpi.reset_video: 1
hw.acpi.cpu.cx_supported: C1/0 C2/1 C3/85
hw.acpi.cpu.cx_lowest: C1
hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00%
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.tz0.temperature: 62.0C
hw.acpi.thermal.tz0.active: -1
hw.acpi.thermal.tz0.passive_cooling: 0
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: 76.5C
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 78.0C
hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.thermal.tz1.temperature: 49.8C
hw.acpi.thermal.tz1.active: -1
hw.acpi.thermal.tz1.passive_cooling: 0
hw.acpi.thermal.tz1.thermal_flags: 0
hw.acpi.thermal.tz1._PSV: -1
hw.acpi.thermal.tz1._HOT: -1
hw.acpi.thermal.tz1._CRT: 50.0C
hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.battery.life: 98
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 2
hw.acpi.battery.info_expire: 5
hw.acpi.acline: 1
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 7.0-CURRENT #58: Thu Aug  4 18:17:40 CEST 2005
    stefan at wombat.fafoe.narf.at:/usr/home/stefan/freebsd/obj/usr/home/stefan/freebsd/src/sys/WOMBAT
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz (1999.78-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x400<CNTX-ID>
real memory  = 804716544 (767 MB)
avail memory = 778219520 (742 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM TP-1M> on motherboard
acpi_ec0: <Embedded Controller: GPE 0x1c, ECDT> port 0x62,0x66 on acpi0
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 3 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 11 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 5 on acpi0
pci_link4: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link5: <ACPI PCI Link LNKF> on acpi0
pci_link6: <ACPI PCI Link LNKG> on acpi0
pci_link7: <ACPI PCI Link LNKH> on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
pci0: <serial bus, USB> at device 29.0 (no driver attached)
pci0: <serial bus, USB> at device 29.1 (no driver attached)
pci0: <serial bus, USB> at device 29.2 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
wi0: <Intersil Prism2.5> mem 0xf8000000-0xf8000fff irq 11 at device 7.0 on pci2
wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.7.4)
wi0: Ethernet address: 00:20:e0:8f:fb:05
pci2: <network, ethernet> at device 8.0 (no driver attached)
pci2: <bridge, PCI-CardBus> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel ICH3 (82801CA)> port 0x1c00-0x1cff,0x18c0-0x18ff irq 3 at device 31.5 on pci0
pcm0: [GIANT-LOCKED]
pcm0: <Analog Devices AD1881A AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
ppc0: <Standard parallel printer port> port 0x3bc-0x3be irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd17ff,0xdc000-0xdffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1999784340 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 28615MB <IC25N030ATCS04 0 CA3OA71A> at ata0-master UDMA100
acd0: DVDROM <HL-DT-STDVD-ROM GDR8081N/0012> at ata1-master UDMA33
Trying to mount root from ufs:/dev/ad0s3a