OLDCARD fails with CURRENT

[Damjan Marion]

Dear all,

OLDCARD works fine on my laptop with kernel compiled from 5.0-RELEASE.
After cvsuping to CURRENT PCMCIA fails with some strange message.

Anybody knows why and what to do?

Damjan

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 The Regents of the University of California. All rights reserved.
FreeBSD 5.1-BETA #0: Fri May 23 22:25:40 GMT 2003
    dmarion at damjan.iskon.local:/usr/src/sys/i386/compile/DAMJAN
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04cb000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04cb244.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 999890825 Hz
CPU: Intel(R) Pentium(R) III Mobile CPU      1000MHz (999.89-MHz 686-class
CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1

Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,MMX,FXSR,SSE>
real memory  = 528285696 (503 MB)
avail memory = 507891712 (484 MB)
Pentium Pro MTRR support enabled
VESA: v3.0, 8000k memory, flags:0x1, mode table:0xc04000e0 (1000040)
VESA: Almador Graphics Chip Accelerated VGA BIOS
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <Acer   TM530   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 7 entries at 0xc00fb700
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf108-0xf10b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_tz1: <thermal zone> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82830M (830M GMCH) SVGA controller> mem
0x90100000-0x9017ffff,0x98000000-0x9fffffff irq 11 at device 2.0 on pci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xa4a0-0xa4bf
irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Microsoft Microsoft 3-Button Mouse with IntelliEye?, rev 2.00/0.00,
addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xa4e0-0xa4ff
irq 10 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0xa800-0xa81f
irq 11 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <serial bus, FireWire> at device 3.0 (no driver attached)
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x7000-0x703f mem
0x80101000-0x80101fff irq 10 at device 8.0 on pci1
fxp0: Ethernet address 00:00:e2:64:e5:a2
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcic0: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.0 on pci1
end (ffffffff) > sc->memlimit (801fffff)
pcic0: PCI Memory allocated: 0x88000000
pcic0: Warning: O2micro OZ68xx chips may not work
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <O2micro 6933 PCI-Cardbus Bridge> irq 10 at device 9.1 on pci1
end (ffffffff) > sc->memlimit (801fffff)
pcic1: PCI Memory allocated: 0x88001000
pcic1: Warning: O2micro OZ68xx chips may not work
pccard1: <PC Card 16-bit bus (classic)> on pcic1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port
0xa890-0xa89f,0xa878-0xa87b,0xa860-0xa867,0xa848-0xa84b,0xa830-0xa837 at
device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 8250 or not responding
sio1 port 0x240-0x247,0x2f8-0x2ff irq 3 drq 3 on acpi0
sio1: type 16550A
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ad0: 19077MB <TOSHIBA MK2018GAP> [38760/16/63] at ata0-master UDMA100
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
pcic0: Failed at 5.0V.  Trying 3.3V.  Please report message to
mobile at freebsd.org
pccard: card inserted, slot 0
pcic1: Failed at 5.0V.  Trying 3.3V.  Please report message to
mobile at freebsd.org
pccard: card inserted, slot 1