Vaio 505GL PC-CARD (pccardd) problmes
Chris Collins
collins at collins-ca.com
Mon Aug 4 17:20:06 PDT 2003
I am running 5.1-current and I think that i read somwhere NEWCARD is default.
I am not sure how else to tell or show to switch.
I have two a linksys WPC11 Wireless Card & and Linksys WPC54G card that I am
trying to get working.
Below is my pccard.conf and dmesg.boot
DMESG
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Mon Aug 4 15:57:24 EDT 2003
root at vaio.collins-ca.com:/usr/obj/usr/src/sys/LAPTOP
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0717000. Preloaded elf
module "/boot/kernel/acpi.ko" at 0xc07172bc. Timecounter "i8254" frequency
1193182 Hz Timecounter "TSC" frequency 1193111222 Hz
CPU: Mobile Intel(R) Pentium(R) III CPU - M 1200MHz (1193.11-MHz 686-class
CPU)
Origin = "GenuineIntel" Id = 0x6b4 Stepping = 4
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,MMX,FXSR,SSE>
real memory = 401080320 (382 MB)
avail memory = 381796352 (364 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY C1 > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdf30
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 2 INTA is routed to irq 9
pcib0: slot 29 INTA is routed to irq 9
pcib0: slot 29 INTB is routed to irq 9
pcib0: possible interrupts: 9
pcib0: slot 31 INTB routed to irq 9 via \\_SB_.LNKB
agp0: <Intel 82830M (830M GMCH) SVGA controller> mem 0xe0000000-
0xe007ffff,0xe8000000-0xefffffff irq 9 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq
9 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Microsoft Microsoft 3-Button Mouse with IntelliEye?, rev 2.00/0.00,
addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq
9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f at
device 29.2 on pci0
pcib0: possible interrupts: 9
pcib0: slot 29 INTC routed to irq 9 via \\_SB_.LNKC
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.09, addr 2
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib1
pcib1: possible interrupts: 9
pcib1: slot 5 INTA routed to irq 9 via \\_SB_.LNKF
pcib1: slot 8 INTA is routed to irq 9
fwohci0: <Texas Instruments TSB43AB22/A> mem 0xe0200000-0xe0203fff,0xe0205000-
0xe02057ff at device 2.0 on pci2
pcib1: slot 2 INTA is routed to irq 9
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 08:00:46:03:01:44:0a:2a
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:46:44:0a:2a
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
cbb0: <RF5C475 PCI-CardBus Bridge> irq 9 at device 5.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x3000-0x303f mem
0xe0204000-0xe0204fff irq 9 at device 8.0 on pci2
fxp0: Ethernet address 08:00:46:77:d6:8a
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-
0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe0100000-0xe01003ff at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller: GPE 0x1c> port 0x66,0x62 on acpi0 sio0 port
0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcffff
on isa0 pmtimer0 on isa0 pcic0 at port 0x3e0 iomem 0xd0000-0xd1fff irq 3 on
isa0
pcic_attach: attach found no sockets
device_probe_and_attach: pcic0 attach returned 6
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cbb0: Unsupported card type detected
ad0: 28615MB <HITACHI_DK23DA-30> [58140/16/63] at ata0-master UDMA100
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0
(probe0:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred
(probe0:umass-sim0:0:0:0): Retrying Command (per Sense Data)
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:0): Medium not present
(probe0:umass-sim0:0:0:0): Unretryable error
Mounting root from ufs:/dev/ad0s1a
PCCARD.CONF
#
# Default PCCARD configuration file
#
# $FreeBSD: src/etc/defaults/pccard.conf,v 1.262 2003/07/22 21:23:01 dds Exp
$ # # Please send new entries for this file to imp at freebsd.org. He likes to
# review them before they are committed to make sure they are correct for #
the style of the file. Please attempt to use "auto" for the config # number
whereever possible. Do not commit IRQs in the "config" lines. # Make sure
that you use tabs rather than multiple spaces for new entires # like the old
ones. <tab>keyword<tab>arguments. # # Removing all IRQ conflicts from this
file can't be done because of some # IRQ-selfish PC-cards. So if you want to
use some of those cards in # your machine, you may need to modify the IRQ
list below. Please put # such overrides in /etc/pccard.conf. You can also
place override # card entries in /etc/pccard.conf, since the first match is
the one that # pccardd will use to configure the card. #
# Generally available IO ports
io 0x240-0x360
# on i386 IRQs can be any of 3 4 5 7 9 10 11 12 14 15
# on pc98 IRQs can be any of 3 5 6 9 10 11 12 13
# but *MUST* *NOT* be used by anything else, unless you are using current #
and a PCI cardbus bridge that allows sharing. Even then, the rules # for
interrupt sharing can be tricky. # Generally available IRQs (Built-in sound-
card owners remove 5)
irq 4 10 11 13
# Available memory slots
memory 0xd4000 96k
# Debug level, so you know how to get more info for maintainers. Put it #
in /etc/pccard.conf #debuglevel 4
# Include user configration file
# This allow you to override or add configurations.
include /etc/pccard.conf
#
# PLEASE KEEP THIS FILE IN ORDER
#
# In order is defined as follows. We sort first by driver type (an, ed, etc)
# and then by CIS strings. Do not commit to this file entries out of #
order. #
########## aic ##########
# Adaptec SlimSCSI (also included with Sony CD-ROM players) card "Adaptec,
Inc." "/APA-1460 .*/"
config 0x9 "aic" ?
insert camcontrol rescan all
# NewMedia Bustoaster SCSI
card "New Media" "SCSI"
config 0x22 "aic" ?
insert camcontrol rescan all
########## an ##########
# Aironet PC4500 2Mbps 802.11 wireless NIC
card "Aironet" "PC4500"
config 0x5 "an" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Aironet PC4800 11Mbps 802.11 wireless NIC
card "Aironet" "PC4800"
config 0x5 "an" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Aironet 340 Series 11Mbps 802.11 wireless NIC
card "Cisco Systems" "340 Series Wireless LAN Adapter"
config auto "an" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Aironet 350 Series 11Mbps 802.11 wireless NIC
card "Cisco Systems" "350 Series Wireless LAN Adapter"
config auto "an" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom sells a rebaded unit
card "Xircom" "Wireless Ethernet Adapter"
config 0x5 "an" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## ata ##########
# Sony VAIO cdrom, Ninja-ATA CD-ROM Drive, MELCO CDN-D12EX
card " " "NinjaATA-"
config auto "ata" ?
logstr "NinjaATA"
# Non-brand Compact Flash Card(32MB)
card " " "KCF 32M"
config 0x1 "ata" ? iosize 16
logstr "Compact Flash Card 32M"
# pc-card from ARCHOS CD-224E cdrom
card "ARC" "ATAPI"
config auto "ata" ?
# Caravelle PSC-IDE 6x ATAPI CD-ROM
card "Caravelle" "/PSC-IDE */"
config 0x2a "ata" ? # 0x1 (flags for wd, not sure for ata)
# <Vendor Unknown> MCD-601p 6x CD-ROM drive.
card "CDROM" "IDE"
config auto "ata" ?
logstr "MCD-601p"
# Lexar Media compact flash
card "/CL ATA FLASH CARD LEXAR */" "TIDALWV"
# auto does not work
config 0x1 "ata" ?
# CNF CD-M
card "CNF CD-M" "CD-ROM"
config auto "ata" ?
logstr "CNF CD-M"
# DATAFAB PCMMD2
card "DATAFAB" "PCMCIA-TO-IDE"
config 0x1 "ata" ?
# DHU Mobile Media CD-ROM
# (no hotplug support)
card "Digital Equipment Corporation." "Digital Mobile Media CD-ROM"
config auto "ata" ?
# EXP DVD-780 DVD-ROM drive
card "/EXP */" "PnPIDE"
config auto "ata" ?
# Toshiba mobile CD-ROM (Bundled with Portege 3110CT)
card "FREECOM" "PCCARD-IDE"
config auto "ata" ? iosize 16
# FUJITSU FlashDiskCard ZEBO-ATA40
card "FUJITSU" "ZEBO-ATA"
config 0x03 "ata" ?
# Greystone Diskdock
card "GREYSTONE PERIPHERAL DISKDOCK" "/.*/"
config default "ata" ?
# HAGIWARA FLASH
card "HAGIWARA" "FLASH"
config default "ata" ?
# Hitachi Flash ATA
card "HITACHI" "/.*FLASH.*/"
config 0x01 "ata" ? iosize 16
# IBM Flash ATA (Ricoh Flash ATA 10MB)
card "IBM" "IBM17JSSFP10"
config auto "ata" ? iosize 16
# IBM IDE PC-CARD CDROM (ThinkPad 240 and others)
card "PCMCIA" "IDE CARD"
config auto "ata" ?
# IBM Portable 4X Speed CD-ROM Drive CD-400
#card "IBM" "PCMCIA CD-ROM Drive CD-400"
# config 0x1 "ata" ? iosize 0x20 # 0x10000 (flags for wd, not sure for
ata)
# IBM CD-20XSeries(IDE PC Card)
card "IBM" "PCMCIA Portable CD-ROM Drive"
config auto "ata" ? iosize 0x1
# IBM Microdrive (CF+ Type II)
card "IBM" "microdrive"
# config 0x03 "ata" ?
config 0x01 "ata" ? iosize 16
# Integral Peripherals Viper HDD Series
card "INTEGRAL PERIPHERALS" "ATA CARD"
# config default "ata" ?
config 0x01 "ata" ? iosize 16
# IO DATA PCMF144/20 (as Flash ATA only)
card "IO DATA" "ATA&MODEM"
config 0x7 "ata" ?
# config auto "sio" ?
# IO DATA CBIDE2 in 16 bit mode
# (bundled with IO DATA CDP-AX24T, Panasonic DVD-ROM LK-RV8171D) card "IO
DATA" "/CBIDE2 */"
config default "ata" ?
# IO Data PCIDE-II (bundled with CDP-TX6, etc.)
card "IO DATA" "PCIDEII"
config auto "ata" ?
# Iomega Zip Drive
card "Iomega" "PCMCIA to 16 bit ATAPI Adapter"
config 0x2 "ata" ?
# KODAK Picture Card
card "KODAK Picture Card" "KODAK"
config default "ata" ?
# TOSHIBA Portable 24X Speed CD-ROM Drive PA2673UJ
card "LOOKMEET" "/CBIDE2 */"
config default "ata" ?
# Maxtor ATA HDD
card "Maxtor" "/MXL.*/"
config 0x03 "ata" ?
# Microtech XpressDock
card "Microtech International Inc." "IDE PCCARD"
config auto "ata" ? 0x20000 iosize 16
# Midori Elec. Flash ATA
card "Midori Elec." "/.*FLASH.*/"
config 0x03 "ata" ?
# Panasonic Flash ATA BN-040ABP3
card "Panasonic" "ATA" "/BN-040AB-M */"
# auto does not work
config 0x1 "ata" ?
logstr "Panasonic Flash ATA BN-040ABP3"
# LK-RM120
card "Panasonic" "LMEK0406"
config 0x22 "ata" ? 0x1
# Another boring, generic ata atapter
card "PC CARD MANUFACTURER" "PCMCIA ATA/ATAPI Adapter"
config auto "ata" ?
# pc-card from PSCD-740 cdrom
card "PCMCIA" "CD-ROM"
config 0x1 "ata" ?
# Novac DVD/CD Station
card "PCMCIA" "PnPIDE"
config auto "ata" ?
# Shining PMIDE-ASC CDROM / Road Warrior Bullet Disk
card "Shining" "PMIDE-ASC"
config auto "ata" ? 0x20000
# Microtech PortableDRIVE25/PCMCIA
card "SHUTTLE TECHNOLOGY LTD." "PCCARD-IDE/ATAPI Adapter"
config auto "ata" ? 0x20000
# XXX NOT SURE SUPPORTED
# CitiDISK & Addonics PocketZIP
#card "Shining" "PMIDE-ASC"
# config default "ata" ? # 0x20000 (flags for wd, not sure for ata)
# Sicon Peripheral PCMCIA ATA/ATAPI Adapter
card "Sicon Peripheral" "PCMCIA ATA/ATAPI Adapter"
config default "ata" ?
# SiliconTech,Inc. Compact PC Card
card "SiliconTech,Inc." "/[0-9]+MB Compact PC Card/"
config 0x1 "ata" ?
# Simple Technology ata flash
card "/Simple Technology */" "STI-ATA"
config auto "ata" ?
# SONY Memory Stick PC Card Adaptor
card "SONY" "/MEMORYSTICK.*/"
config 0x01 "ata" ?
iosize 16
# SunDisk Flash ATA
# (OEM: Epson Flash Packer)
card "SunDisk" "/.*/"
config 0x1 "ata" ?
# T-POWER Flash ATA
card "/T-POWER */" "/.*/"
config 0x1 "ata" ?
# TDK Flash ATA
card "TDK TC_H." "/.*/"
config 0x1 "ata" ?
# IO Data CBIDE (bundled with CDP-FX24, etc.)
card "WIT" "IDE16"
config auto "ata" ?
# LIP-32B attached to Logitec LCW-PD648PI
card "WORKBIT" "ATA-32Bi(16)"
config default "ata" ?
# Viking ATA Flash card
card "/VIKING ATA/CF FLASH CARD */" "/TOR/AM */"
config 0x2 "ata" ?
########## awi ##########
# Generic AMD Am79c930 based card
# Melco WLI-PCM
card "AMD" "Am79C930"
config 0x1 "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Bay Networks Baystack 650 Wireless LAN
card "Bay Networks" "BayStack 650 Wireless LAN"
config 0x1 "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Bay Networks Baystack 660 Wireless LAN
card "Bay Networks" "BayStack 660 Wireless LAN"
config auto "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Farallon SkyLINE Wireless
card "Farallon" "SkyLINE Wireless"
config auto "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ICom SL-200
card "Icom" "SL-200"
config auto "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Teletronics WL2000D 2Mbps wireless card
# Might not be right, reports are that it reports ether of 0:0:0:0:0:0
card "OEM" "WLAN/WPMCIA"
config auto "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ZoomAir 4000
card "Zoom" "Air-4000"
config auto "awi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## cnw ##########
# NetWave AirSurfer
# NOTE: For some machines, wait cycle for memory access is required. # you
should change "0x40" on the last part of "cardmem" line to "0x44", # like:
# cardmem 0xd4000 0x20000 0x9000 0x44
# IBM ThinkPads are known to require this change.
# Xircom CreditCard Netwave
card "Xircom" "CreditCard Netwave"
config 0x01 "cnw" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## cs ##########
# NOTE: This likely doesn't work, but might.
# IBM EtherJet PC Card 16bit version
card "IBM" "EtherJet PC Card"
config auto "cs" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## ed ##########
# No-brand NE2000 compatible card (FCC ID: LXLC1LANTB)
card " " "Ethernet Combo card"
config auto "ed" ? 0x10
logstr "NE2000 compatible card"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Map Japan MPL-972
card "2408LAN" "Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Accton EN2212
# Very slow! (PIO mode)
card "ACCTON" "EN2212"
config auto "ed" ? 0x30
ether 0xff0 # 00:00:e8
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Accton EN2216
card "ACCTON" "EN2216-PCMCIA-ETHERNET"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Allied Telesis CentreCOM LA-PCM
card "Allied Telesis,K.K" "Ethernet LAN Card"
config default "ed" ? 0x10
ether 0xff0 # 00:00:f4
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Allied Telesis CentreCOM LA-PCM_V2 ethernet card
# NTT-DATA ASTROWINK-M/MMOIL(IrLAN) ethernet card
card "Allied Telesis, K.K." "CentreCOM LA-PCM_V2"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Allied Telesis CentreCOM LA100-PCM-T V2
card "Allied Telesis, K.K." "CentreCOM LA100-PCM-T V2 100/10M LAN PC Card"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Allied Telesis CentreCOM LA-PCM V3
card "Allied Telesis K.K." "LA-PCM V3"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# AmbiCom 10BaseT card
card "AmbiCom Inc" "AMB8002T"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Belkin F5D5020
card "Belkin" "F5D5020-PCMCIA-Network-Card"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Billionton LNA-100B
card "Billionton" "LNA-100B"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Billionton LNT-10TB
card "Billionton" "LNT-10TB"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Billionton LNT-10TN
card "Billionton" "LNT-10TN"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BUFFALO LPC-CF-CLT
card "BUFFALO" "LPC-CF-CLT"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BUFFALO LPC2-CLT
card "BUFFALO" "LPC2-CLT"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BUFFALO LPC3-CLT
card "BUFFALO" "LPC3-CLT"
config auto "ed" ? 0x30000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BUFFALO LPC3-CLX
card "BUFFALO" "LPC3-CLX"
config auto "ed" ? 0x30000
ether 0x1c8
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# CNet BC40 adapter
card "CNet" "CN40BC Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# COREGA FEther PCC-TXF
card "corega" "FEther PCC-TXF"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# COREGA Ether PCC-T and COREGA EtherII PCC-T
card "corega K.K." "/corega Ether(II)? PCC-T/"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# COREGA FastEther PCC-TX
card "corega K.K." "corega FastEther PCC-TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# COREGA FEther PCC-TXD
card "corega K.K." "corega FEther PCC-TXD"
config auto "ed" ? 0x30000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Corega PCM-T
card "Corega,K.K." "Ethernet LAN Card"
config auto "ed" ?
ether 0xff0 # 00:00:f4
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Surecome EP-427X PCMCIA ethernet
card "CouplerlessPCMCIA" "100BASE"
config auto "ed" ? 0x30000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# CyQ've ELA-010
card "CyQ've" "ELA-010"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# CyQ've ELA-110 and ELA-110E
card "CyQ've" "/ELA-110E? 10/100M LAN Card/"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# D-Link DE-650 and DE-660
card "D-Link" "/DE-6[56]0/"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# D-Link DFE-650 Fast Ethernet Card
card "D-Link" "DFE-650"
config auto "ed" ? 0x80010
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# D-Link DFE-670 Fast Ethernet Card
card "D-Link" "DFE-670TXD"
config auto "ed" ? 0x80010
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# D-Link DME-560T LAN/FAX/MODEM Card (as Ethernet)
card "D-Link" "DME560T"
config default "ed" ?
# config auto "sio" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Danpex (Alloy, etc.) EN-6200P2
card "DANPEX" "EN-6200P2"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Dayna Communications CommuniCard E
card "Dayna Communications, Inc." "CommuniCard E"
config auto "ed" ? 0x10
ether 0x110 # 00:80:19
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Digital DEPCM-BA Ethernet
card "DIGITAL" "DEPCM-XX"
config auto "ed" ? 0x10
ether 0xff0 # 00:00:e8
# ether 0x1c0 # 00:00:e8 -- seen on a rev. C01 card
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Planex FNW-3600-T and FNW-3600-TX DirectDock (second model) card "Dual
Speed" "/10/100( Port Attached)? PC Card/"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Dynalink L100C16
card "Dynalink" "L100C16"
config auto "ed" ?
insert /etc/pccard_ether $device
remove /etc/pccard_ether $device stop
# Linksys Combo PCMCIA Ethernet Card
card "E-CARD" "E-CARD"
config auto "ed" ?
logstr "Linksys Combo Ethernet Card"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Eiger Labs Ethernet COMBO
card "EIGER Labs Inc." "Ethernet COMBO Card"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# XXX Compex Net-A adapter, Telecom SuperSocket RE450T,
# Apollo PCMCIA Ethernet Adapter, PLANEX ENW-3503-T and
# Fiber line 10M Ethernet COMBO have same manufacturer and
# card version string. They should be distinguished by
# other info. (such as additional information or OEM-ID/product-ID).
# Note: There are several revisions of the card on the market.
# Type A needs no "ether" line.
# Type B needs "ether 0x110" line.
# Type C needs "ether 0xff0" line.
# Yet more revisions exist, reportedly.
# If you see strange MAC address shown by ifconfig command,
# try other config.
card "Ethernet" "Adapter"
config auto "ed" ?
# ether 0x110 # 00:e0:98
ether 0xff0 # 00:e0:98
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# pci Ethernet Adapter Card
card "Ethernet" "CF Size PC Card"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# "Ethernet Adapter" "E2000 PCMCIA Ethernet"
card "Ethernet Adapter" "E2000 PCMCIA Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ADDTRON EP-210A
card "EP-210 PCMCIA LAN CARD." "/.*/"
config auto "ed" ? 0x10
ether 0x110 # 00:40:33
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Planex FNW-3700-T Fast Ethernet
card "Fast Ethernet" "16-bit PC Card"
config auto "ed" ? 0x30000
logstr "Planex FNW-3700-T"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Planex FNW-3600-T 16bit Fast Ethernet (old model)
card "Fast Ethernet" "Adapter"
config auto "ed" ? 0x80000
logstr "Planex FNW-3600-T"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# TDK Grey Cell GCS2000 and GCS2220
card "Grey Cell" "/GCS2(00|22)0/"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# GVC NIC-2000P Ethernet Card
card "GVC" "NIC-2000p"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# IBM PCMCIA Ethernet I/II, RIOS PC CARD II ETHERNET
card "IBM Corp." "Ethernet"
config auto "ed" ?
ether 0xff0 # 08:00:5a 00:04:ac 00:06:29
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# AR-P500 ethernet card, Planet Communications Smart COM 3500 same as # model
ENW-3500 and ENW-3501-T, IC-CARD Ethernet, SYSCOM SC100 Ethernet Card #
ELECOM Laneed LD-CDY, IC-CARD+ Ethernet card card "/^IC-CARD\+?$/" "/^IC-
CARD\+?$/"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# I/O DATA PCLA/T
card "I-O DATA" "PCLA"
config auto "ed" ? 0x10
# ether 0x1c0 # 00:a0:b0
ether 0xff0 # 00:a0:b0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# I-O DATA PCET/100-CL
card "IO DATA" "PCET100CL"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# I-O DATA PCET/TX
card "IO DATA" "PCETTX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# I-O DATA PCET/TX-R
card "IO DATA" "PCETTXR"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# I-O DATA PCLA/TE
card "IO DATA" "PCLATE"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# KANSAI ELECTRIC KLA-PCM/T
card "KANSAI ELECTRIC CO.,LTD" "KLA-PCM/T"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Kingston KNE-PC2
card "Kingston" "KNE-PC2"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Kingston KNE-PCM/x Ethernet
card "Kingston Technology Corp." "/EtheRx PC Card Ethernet.*/"
config auto "ed" ?
ether 0xff0 # 00:c0:f0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Laneed LD-10/100CD
card "Laneed" "LD-10/100CD"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Laneed LD-CDF, LD-CDS
card "Laneed" "/LD-CD[FS]/"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Laneed LD-CDL/TX
card "Laneed" "LD-CDL/TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys Combo PCMCIA EthernetCard (model EC2T on box)
card "Linksys" "Combo PCMCIA EthernetCard (EC2T)"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys Combo PCMCIA Ethernet Card
card "LINKSYS" "E-CARD"
config auto "ed" ? 0x10
logstr "Linksys Combo Ethernet Card"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys PCMLM56
# Not currently working for me, but others say it does.
card "Linksys" "EtherFast 10&100 + 56K PC Card (PCMLM56)"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys EtherFast 10/100 Intergrated PC Card (PCM100)
card "Linksys" "EtherFast 10/100 Integrated PC Card (PCM100)"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys EtherFast 10/100 PC Card (PCMPC100), model V2 and V3
card "Linksys" "/Ether[Ff]ast 10/100 PC Card \(PCMPC100.*\)/"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Logitec LPM-LN100TX 100BASE-TX Ethernet LAN CARD
card "Logitec" "LPM-LN100TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Logitec LPM-LN20T
card "Logitec" "LPM-LN20T"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Socket LP-E (WinCE Low Power Ethernet)
card "Low Power Ethernet LAN Adapter" "Socket Communications, Inc"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Laneed LD-CDWA (DP83902A), MACNICA Ethernet ME1 for JEIDA
card "MACNICA" "ME1-JEIDA"
config auto "ed" ?
ether 0xb8 # 08:00:42
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Matsushita Electric Industrial Co.,LTD. CF-VEL211P-B
card "Matsushita Electric Industrial Co.,LTD." "CF-VEL211"
config auto "ed" ?
ether 0xff0 # 00:80:45
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# MELCO LPC2-T
card "MELCO" "LPC2-T"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# MELCO LPC2-TX
card "MELCO" "LPC2-TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# MELCO LPC3-TX
card "MELCO" "LPC3-TX"
config auto "ed" ? 0x30000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# National Semiconductor InfoMover 4100 and NE4100
card "National Semiconductor" "/InfoMover (NE)?4100/"
config auto "ed" ?
ether 0xff0 # 08:00:17
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NDC Ethernet Instant-Link NE2000 clone
card "NDC" "Ethernet"
config auto "ed" ? 0x30
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Addtron NE-2000 compatible NIC
card "NE2000 Compatible PC Card" "PCMCIA"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NEC PC-9801N-J12
card "NEC" "PC-9801N-J12"
config auto "ed" ?
ether 0xff0 # 00:00:4c
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BayNetworks NETGEAR FA410TXC Fast Ethernet
card "NETGEAR" "FA410TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BayNetworks NETGEAR FA411 Fast Ethernet
card "NETGEAR" "FA411"
config auto "ed" ? 0x30000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Network Everywhere Ethernet 10BaseT PC Card
card "Network Everywhere" "Ethernet 10BaseT PC Card"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Network Everywhere Ethernet Fast Ethernet 10/100 PC Card
card "Network Everywhere" "Fast Ethernet 10/100 PC Card"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# New Media Corporation LiveWire 10/100
card "New Media Corporation" "LiveWire 10/100"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NextCom Next Hawk Etherneet Adapter
card "NextCom K.K." "Next Hawk"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Nihon Unisys, Ltd. JPF0400-ETH and JPF0400-LAN
card "Nihon Unisys, Ltd." "/JPF0400-(ETH|LAN)/"
config auto "ed" ?
ether 0xff0 # 00:80:45
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Nortel Networks BayStack 22 Ethernet 10/100 PC Card
card "Nortel" "BAYSTACK22-PCMCIA-ETHERNET"
config auto "ed" ? 0x30000
ether 0x1c8
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Longshine LCS-8534TB
card "PCMCIA" "/^Ethernet$/"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# No-brand NE-2000 compatible card
card "PCMCIA" "ETHERNET V1.0"
config auto "ed" ? 0x10
ether 0xff0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Telecom Device SuperSocket HPC100
card "PCMCIA" "FastEthernet"
config auto "ed" ? 0x30000
logstr "Telecom Device SuperSocket HPC100"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Billionton 10Base-TX ETHERNET PCCARD (aka UE2216)
# Also Genuius "Ethernet ME3000II SE"
card "PCMCIA" "PCMCIA-ETHERNET-CARD"
config auto "ed" ? 0x10
logstr "UE2216"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Planet Smart COM 2000, Melco LPC-T
card "PCMCIA" "UE2212"
config auto "ed" ? 0x10
ether 0xff0 # 00:00:e8
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# GVC 10Mbps Ethernet Card
card "PCMCIA" "Ethernet Card"
config auto "ed" ?
logstr "Generic PCMCIA Ethernet Card"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Billionton LM5LT-10N
# Works as an Ethernet card
card "PCMCIA 10+56Combo" "LM5LT-10N"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# EXPsys PCMCIA Ethernet Combo, Relia PCMCIA Ethernet
card "PCMCIA LAN" "Ethernet"
config auto "ed" ?
logstr "EXPsys Ethernet"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# LinkMates LM 336 LAN Fax/Modem PC Card (as Ethernet only)
card "PCMCIAs" "ComboCard"
config 0x24 "ed" ? 0x10
# config auto "sio" ?
logstr "LinkMates LM 336"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Telecom Device SuperSocket LM336 (as Ethernet only)
card "PCMCIAs" "LanModem"
config default "ed" ?
# config auto "sio" ?
logstr "SuperSocket LM336"
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# PreMax PE-200 Ethernet Card
card "/PMX */" "PE-200"
config auto "ed" ? 0x10
ether 0x7f0 # 00:20:e0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Psion Dacom Gold Card Ethernet
card "Psion Dacom" "Gold Card Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Psion Dacom Gold Card V34 Ethernet GSM
# as ethernet
card "Psion Dacom" "Gold Card V34 Ethernet GSM"
config auto "ed" ?
# config auto "sio" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# RIOS PC CARD3 ETHERNET
card "RIOS Systems Co." "PC CARD3 ETHERNET"
config auto "ed" ?
ether 0xff0 # 00:00:48
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# RPTI EP401 Ethernet card
card "RPTI" "EP401 Ethernet NE2000 Compatible"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# SCM Ethernet Combo (*Not SMC :-)*)
card "SCM" "Ethernet Combo card"
config auto "ed" ? 0x10
ether 0xff0 # 00:20:cb
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Epson EEN10B Ethernet Card
card "Seiko Epson Corp." "Ethernet"
config auto "ed" ? 0x10
ether 0xff0 # 00:00:48
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# SMC EXCard-10-PCMCIA
card "SMC" "EZCard-10-PCMCIA"
config 0x20 "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3way 3WL-847-TX
card "SUN WAY" "3WL-847-TX 100BASE-TX"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Surecom EtherPerfect EP-427
card "TAMARACK" "Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# TDK LAK-CD031
card "TDK" "/LAK-CD031.*/"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Telecom Device SuperSocket RE450T
card "Telecom Device K.K." "SuperSocket RE450T"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Telecom Device SuperSocket RE550T
card "Telecom Device K.K." "SuperSocket RE550T"
config auto "ed" ? 0x80000
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Toshiba Joho System PTJ-LAN/T
card "TJ" "Ethernet"
config auto "ed" ? 0x10
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# XXX NOT SUPPORTED YET
# TOSHIBA LABCTA00A (Add `option TOSH_ETHER' line to your kernel #
configuration file and rebuilding kernel.) #card "TOSHIBA" "LANCT00A"
# config default "ed" ? 0x10
# cardmem 0xd0000 0x0000 32k
## cardmem 0xd8000 0x0000 32k
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# Xircom CompactCard Ethernet 10 (CFE-10)
card "Xircom" "CompactCard Ethernet"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## ep ##########
# 3Com Fast Etherlink 3C574TX
card "3Com" "3C574-TX Fast EtherLink PC Card"
config auto "ep" ? 0x1
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3Com Megahertz 3CCFEM556BI, 3CXEM556 and model B
# as ethernet
card "3Com" "/Megahertz 3C(CF|X)EM556/"
config default "ep" ? 0x1
# config auto "sio" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3Com Megahertz 574B same as 3Com Fast Etherlink 3C574B
card "3Com" "Megahertz 574B"
config auto "ep" ? 0x1
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3Com Etherlink III 3CXE589EC and 3CXE589ET
card "3Com" "Megahertz 589E"
config auto "ep" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3Com OfficeConnect 3CXSH572BT
card "3Com" "OfficeConnect 572B"
config auto "ep" ? 0x1
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3Com Etherlink III 3C562 (as Network)
# Don't think this will work.
#card "3Com Corporation" "3C562"
# config 0x9 "ep" ?
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# 3Com Etherlink III 3C589, 3C589B, 3C589C, 3C589D
card "3Com Corporation" "/3C589/"
config auto "ep" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Farallon EtherMac
card "Farallon" "ENet"
config auto "ep" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## ex ##########
# Olicom OC2220
card "Olicom" "Ethernet"
config 0x1 "ex" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## fe ##########
# CONTEC C-NET(PC)C Ethernet
card "CONTEC Co.,Ltd." "/C-NET\(PC\)C.*/"
config auto "fe" ?
ether 0x58 # 00:80:4c
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Fujitsu MBH10303 Ethernet PCMCIA
card "EAGLE Technology" "/NE200 ETHERNET LAN MBH10303 */"
config auto "fe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Eiger Labs EPX-10BT
card "Eiger labs,Inc." "EPX-10BT PC Card Ethernet 10BT"
config auto "fe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Fujitsu FMV-J182, FMV-J182A
card "FUJITSU" "LAN Card(FMV-J182)"
config auto "fe" ?
# These cards have same ID strings, and different MAC address
# locations.
# ether 0xf2c # 00:00:0e #FMV-J182
ether 0x1cc # 00:00:0e #FMV-J182A
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Fujitsu Towa LA501 Ethernet
card "FUJITSU TOWA" "LA501"
config auto "fe" ? 0x10
ether 0x332 # 00:00:0e
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# HITACHI HT-4840-11
card "HITACHI" "HT-4840-11"
config auto "fe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NextCom J Link NC5310
card "NextComK.K." "/NC5310 Ver1\.0.*/"
config auto "fe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# RATOC REX-5588, REX-9822, REX-4886
card "PCMCIA LAN MBH10304 ES" " 01"
config auto "fe" ?
# ether 0x32c # 00:c0:d0 # many minor revs....
# ether 0x328 # 00:c0:d0
ether 0x200 # 00:c0:d0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Fujitsu MBH10302
card "PCMCIA MBH10302" "01"
config auto "fe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# RATOC REX-R280
card "RATOC System Inc." "10BASE_T CARD R280"
config auto "fe" ?
ether 0x1fc # 00:c0:d0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# TDK LAK-CD021, LAK-CD021A, LAK-CD021BX
card "TDK" "LAC-CD02x"
config auto "fe" ?
# These cards have same ID strings, and different MAC address
# locations.
# ether 0x92 # 00:80:98 # LAC-CD021, LAC-021A
# ether 0x96 # 00:80:98 # LAC-CD021BX
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## fdc ##########
# Libretto Floppy disk
card "Y-E DATA" "External FDD"
config 0x4 "fdc" ?
########## gp ##########
# XXX NOT SUPPORTED YET
# National Instruments PCMCIA-GPIB Cards
#card "National Instruments" "PCMCIA-GPIB"
# config default "gp" pio
########## hss ##########
# XXX NOT SUPPORTED YET
# Hitachi microcomputer speech synthesizer card
#card "/HITACHI MICROCOMPUTER SYSTEM LTD.*/" "MSSHVPC02"
# config default "hss" pio
########## joy ##########
# IO DATA PCJOY
card "IO DATA" "PCJOY"
config auto "joy" ?
# config 0x1 "joy" pio
# config 0x2 "joy" pio
# Game Card B236 by BONDWELL
card "BONDWELL" "B236"
config auto "joy" ?
########## ncv ##########
# New Media Corporation BASICS SCSI
# (Do not put this entry under Bustoaster)
card "BASICS by New Media Corporation" "SCSI Sym53C500"
config auto "ncv" ?
# Media Intelligent SCSI-2 PC Card MSC-200
card "EPSON" "SCSI-2 PC Card SC200"
config auto "ncv" ?
# KME (TAXAN ICD-400PN, etc.)
card "KME" "KXLC002"
config auto "ncv" ? 0xb4d00000
# KME KXLC004
card "KME" "KXLC004"
config auto "ncv" ? 0xb4d00100
# IO DATA PCSC-DV
# Macnica Miracle SCSI mPS100
card "MACNICA" "MIRACLE SCSI" "mPS100" "D.0"
config auto "ncv" ? 0xb6250000
# Macnica Miracle SCSI-II mPS110
card "MACNICA" "MIRACLE SCSI-II mPS110"
config auto "ncv" ? 0
# NEC PC-9801N-J03R
card "NEC" "PC-9801N-J03R"
config auto "ncv" ? 0
# Qlogic Fast SCSI
card "QLOGIC CORPORATION" "pc05"
config auto "ncv" ? 0x84d00000
# RATOC REX-9530
card "RATOC System Inc." "/SCSI2 CARD.*/"
config auto "ncv" ? 0x84d00000
# RATOC REX-5572 (as SCSI only)
card "RATOC System Inc." "/SOUND/SCSI2 CARD.*/"
config auto "ncv" ? 0x84d00000
# cardio 0x640 0x10
iosize 16
########## nsp ##########
# WORKBIT Ninja SCSI series
card "IO DATA" "/CBSC16 */"
config auto "nsp" ?
# Hewlett Packard M820e (CD-writer)
card "/KME */" "SCSI-CARD-001"
config auto "nsp" ?
# WORKBIT Ninja SCSI series
card "WBT" "NinjaSCSI-3"
config auto "nsp" ?
# WORKBIT Ninja SCSI series (PIO mode)
# (If you want to use them in PIO mode comment out above and uncommnet
below.) #card "WBT" "NinjaSCSI-3"
# config auto "nsp" ? 0x100
########## opl ##########
# XXX NOT SUPPORTED YET
# RATOC REX-5570 Sound Card
#card "1195 RATOC System Inc." "REX5570 SOUND CARD"
# config default "opl" ?
########## ray ##########
# WebGEAR Aviator 2.4
card "WebGear" "PC Card WLAN Adapter"
config auto "ray" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Raytheon Raylink 802.11 Wireless LAN
card "RAYTHEON" "RayLink PC Card WLAN Adapter"
config auto "ray" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## scc ##########
# XXX NOT SUPPORTED YET
# IBM Smart Capture Card
#card "IBM Corp." "Video Capture"
# config default "scc" pio
# cardmem 0xd4000 0x0 0x8000
########## sio ##########
# 3Com/USR/MegaHertz 3CCM156
card "3COM" "3CCM156"
config auto "sio" ?
# 3com/USR/Megahertz 3CCM556
card "3Com" "3CXM/3CCM556"
config auto "sio" ?
# 3Com Etherlink III 3C562 and 3C563 (as Modem)
card "3Com Corporation" "/3C56[23]/"
config 0x09 "sio" ?
# config auto "sio" ?
# ADVANTECH COMpad-32/85 (dual port, but only one works)
card "ADVANTECH" "COMpad-32/85"
config auto "sio" ? 0x330
# Apex Data 28.8 PC Card "MOBILE PLUS Cellular" modem.
card "AD PC_CARD" "RC288ACL"
config auto "sio" ?
# AIWA PV-JF288
card "AIWA CO.,LTD." "/PV-JF288 */"
config auto "sio" ?
# AIWA PV-JF3356
card "AIWA CO.,LTD. MODEM" "PV-JF3356"
config auto "sio" ? 0x40000
# APEX DATA MultiCard (as Modem only)
card "APEX DATA" "MULTICARD"
config 0xb "sio" ?
# config auto "sio" ?
# Eiger 33.6 modem
card "AT&T" "V34+ Fax Modem"
config auto "sio" ?
# AT&T Paradyne KeepInTouch 14.4 modem
card "AT&T Paradyne" "KeepInTouch Card"
config auto "sio" ?
reset 1000
# BUG Linkboy D64K (ISDN)
card "BUG Inc." "Linkboy D64K"
config auto "sio" ?
# Portable Add Ons FreeSpirit 56K/ISDN Card
card "Portable Add Ons" "FreeSpirit Global 56K"
config auto "sio" ?
# NewMedia 14.4K FAX/Data Modem
card "CIRRUS LOGIC" "FAX MODEM"
config auto "sio" ?
# COM1 SA
card "COM1 SA" "/MC2(18|20) CARD/"
config auto "sio" ?
# Digiteam Expresso 14.4 Modem
card "Digiteam GmbH" "Expresso Modem"
config auto "sio" ?
# Eicon DIVA T/A
# at at menu Config menu
# at>vc View current profile
# at>vd View troubleshooting information
card "Eicon Technology" "DIVA T/A"
config auto "sio" ?
# Ericsson DC23 GSM modem card
card "ERICSSON" "Modem, DC23"
config auto "sio" ?
# GATEWAY 2000 FAX/Data Modem (14.4K)
card "GATEWAY2000" "CC3144"
config auto "sio" ?
# This one does work though
card "HAYES" "OPT288"
config auto "sio" ?
# Hayes OPTIMA 288 FAX/Data Modem
# currently does not work on my machine
card "Hayes" "OPTIMA 288 + FAX fo"
config auto "sio" ?
reset 10000
# IBM Push/Pop Modem (14.4K)
card "IBM" "Push/Pop Modem(14.4K)"
config auto "sio" ?
# IBM 56k PCCCARD modem
card "IBM" "56K PC Card Modem"
config auto "sio" ?
# Intel EtherExpress(TM) PRO/100 LAN/Modem PC Card Adapter (as modem)
card "Intel" "EtherExpress(TM) PRO/100 LAN/Modem PC Card Adapter"
config 0x1f "sio" ?
# config auto "sio" ?
# US Robotics Worldport 14400
card "Intel" "MODEM 2400+"
config auto "sio" ?
# Intelligent SurfCard
card "Intelligent" "PCMCIA FAX+MODEM"
config auto "sio" ?
reset 1000
# Megahertz XJEM3288 (as modem)
card "MEGAHERTZ" "CC/XJEM3288"
config auto "sio" ?
# Megahertz XJEM1336 (as modem)
card "MEGAHERTZ" "CC/XJEM3336"
config auto "sio" ?
# Megahertz XJ1144, XJ2144 (US and JP), XJ2288, XJ3288
card "MEGAHERTZ" "/XJ[0-9]+/"
config auto "sio" ?
# Megahertz XJ-CC4288
card "Megahertz" "XJ-CC4288"
config auto "sio" ?
# Megahertz XJ4336
card "Megahertz" "XJ4336-CC4336"
config auto "sio" ?
# XXX generic serial?
# Megahertz X-Jack Ethernet/Modem 14.4K (as Modem only)
card "Megahertz" "XJEM1144/CCEM1144"
config 0x27 "sio" ?
# config auto "sio" ?
# Motorola Montana
card "Motorola" "MONTANA 33.6 FAX/MODEM"
config auto "sio" ?
# XXX generic serial?
# Motorola Marine multifunction card (as modem)
card "Motorola, Inc." "MARINER MODEM/FAX/LAN"
config 0x35 "sio" ?
# config auto "sio" ?
# NTT ThunderCard Modem
card "NTT-IT CO., LTD" "ThunderCard AVF288, V.34"
config auto "sio" ?
# NTT DoCoMo Mobile D Card 96P1
card "NTT DoCoMo" "Mobile D Card 96P1"
config auto "sio" ? 0x82
# NTT DoCoMo (formerly NTT Personal) Paldio 611S
card "NTT DoCoMo" "PALDIO 611S PC CARD"
config auto "sio" ? 0x40000
# NTT DoCoMo DATA/FAX Adapter
card "NTT DoCoMo" "PCMCIA DATA/FAX ADAPTER 9600 Mark2"
config auto "sio" ?
# NTT DoCoMo DATA/FAX Adapter
card "NTT DoCoMo" "/PCMCIA DATA/FAX.*/"
config auto "sio" ? 0x82
# NTT-IT ThunderCard
card "NTT Intelligent Technology Co., Ltd." "ThunderCard DD128"
config auto "sio" ? 0x80
reset 1000
# NTT DoCoMo (formerly NTT Personal) FAX/Data 32K PHS Card Paldio 321S
card "NTT Personal" "32K Paldio 321S PC CARD"
config auto "sio" ?
# config auto "sio" ? 0x40000
# NTT DoCoMo (formerly NTT Personal) FAX/Data 32K PHS Card Paldio 341S
card "NTT Personal" "32K Paldio 341S PC CARD"
config auto "sio" ?
# NTT Personal Paldio Data Card DC-1S
card "NTT Personal" "/Paldio Data.*/" "DC-1S"
config auto "sio" ? 0x40000
# Nokia Cellular Data Card DTP-2 and DTP-2 ver II
# This Nokia example allows either 1 or 2 Nokia cards to be fitted. # With 2
Mobile Phones and Multilink PPP you can get a 19200 data channel. # Nokia
Cellular Data Card card "Nokia Mobile Phones" "/DTP-2( ver II)?/"
# config 0x23 "sio" ?
# config 0x24 "sio" ?
config auto "sio" ?
# Novalink NovaModem 144
card "NovaLink Tech." "/NovaModem 144 */"
config auto "sio" ?
# Novatel Merlin CDPD card (wireless modem)
card "Novatel Wireless" "Merlin Type II Wireless IP Modem"
config auto "sio" ?
# Omron ME2814 FAX/DATA MODEM
card "OMRON" "ME2814 FAX/DATA MOD"
config auto "sio" ?
# Omron MD24XCA FAX/Data Modem
card "OMRON Corp." "MD24XCA"
config auto "sio" ?
# config auto "sio" pio
reset 10000
# Option International PCMCIA55K06
card "Option International" "GSM Data/Fax/SMS Modem"
config auto "sio" ?
# Banksia CardModem 56
card "PCCardModem" "CardModem 56"
config auto "sio" ?
# Eiger PCCARD modem
# Apparently this modem does not work unless the recommended
# init string (AT&F&C1&D2) is supplied.
card "/PCMCIA */" "/33\.6K Fax/Modem */"
config auto "sio" ?
# Actiontec Datalink with v.90 upgrade
card "/PCMCIA */" "/56K V\.90 Fax Modem (LK) */"
config auto "sio" ?
# Billionton 56Kbps Fax Modem
card "PCMCIA CARD 56KFaxModem" "FM56C-NFS"
config auto "sio" ?
# PREMAX FM288 FAX/Data Modem
card "PREMAX" "/FM288 */"
config auto "sio" ?
# Panasonic FM-RADIO card
card "Panasonic" "CF-JVR101"
config auto "sio" ?
# config auto "sio" pio
# Panasonic KX-PH402D
card "Panasonic" "KX-PH402D"
config auto "sio" ?
# Panasonic Modem Card TO-706C
card "Panasonic" "TO-706C"
config auto "sio" ?
# Panasonic Modem Card TO-706C
card "Panasonic" "TO-CAF288"
config auto "sio" ?
# Panasonic TO-CAF56K FAX/Data Modem
card "Panasonic Co." "TO-CAF56K"
# config auto "sio" pio
config auto "sio" ?
reset 10000
# Random modem bundled with Dell systems
card "Psion Dacom" "Gold Card Global 56K+Fax"
config auto "sio" ?
# RFI HotLine serial card
card "RFI" "RS-232 ComCard Rev.II"
config auto "sio" ?
# SII MC-6530, MC-6550 and MC-P200
card "SII" "/PHS (DATA|LINK) (32S|64)/"
config auto "sio" ? 0x40000
# TDK 14.4 FAX/Data Modem
card "TDK" "/DF1414(EX)? DATA/FAX MODEM/"
config auto "sio" ?
# TDK DN1280R
card "TDK" "DN1280R"
config auto "sio" ?
reset 1000
# TDK DP9600
card "TDK" "DP9600"
config auto "sio" ? 0x40000
# TDK Multifunctioon Card (as Modem)
card "TDK" "GlobalNetworker 3410/3412"
config auto "sio" ? 0x40000
# Toshiba Modem/LAN card IPC5001B (as Modem)
card "TOSHIBA" "Modem/LAN Card"
config 0x25 "sio" ?
# config auto "sio" ?
# 3Com/USR/Toshiba SLIMV90
card "TOSHIBA" "SLIMV90"
config auto "sio" ?
# 3Com/NoteWorthy 56K modem (bundled with Toshiba notebooks) card "Toshiba
America" "3CXM056-BNW"
config auto "sio" ?
# U.S. Robotics XJ1560 and XJ1560J, Megahertz XJ1336
card "U.S. Robotics" "/XJ/CC1(336|560)J?/"
config auto "sio" ?
# US Robotics Sportster PCMCIA V.34
# US Robotics COURIER PCMCIA V.34
card "USRobotics" "PCMCIA 28800 Data/F"
config auto "sio" ?
# Viking V.90/K56Flex modem
card "Viking" "V.90 K56flex"
config auto "sio" ?
# Xircom CreditCard Ethernet 10/100 + modem (modem part)
card "Xircom" "CreditCard Ethernet+Modem 33.6"
config 0x23 "sio" ?
# config auto "sio" ?
# Xircom GlobalACCESS modem
card "Xircom" "CreditCard Modem 56 - GlobalACCESS"
config auto "sio" ?
# Xircom CreditCard Modem
card "Xircom" "CreditCard Modem CM-56T"
config auto "sio" ?
reset 100
# Zonet 56Kbps FAX/Modem PC Card
card "PC CARD" "56Kbps Fax Modem PC Card"
config auto "sio" ?
# Zoom 56K modem
# Freezes your system entirely if you don't have the reset.. card "Zoom
Telephonics, Inc." "PCMCIA 56K LT DataFax"
config auto "sio" ?
reset 1000
########## sn ##########
# Megahertz X-Jack Ethernet
card "Megahertz" "CC10BT/2"
config auto "sn" ?
ether attr2
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Megahertz Ethernet Adapter
card "Megahertz" "ETHERNET ADAPTOR"
config auto "sn" ?
ether attr2
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# MELCO LPC-TX
card "MELCO/SMC" "LPC-TX"
config auto "sn" ?
ether 0x4a # 00:a0:dc
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# SMC EtherEZ Combo(SMC8020BT)
card "SMC" "EtherEZ Ethernet 8020"
config auto "sn" ?
# ether 0x9a # 00:00:c0
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Victor M-MOIL CARD
card "JVC" "MiniMoil Ethernet Card"
config auto "sn" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## spc ##########
# XXX NOT SUPPORTED YET
# REX5535AC, REX5535X SCSI
#card "PCMCIA SCSI MBH10401" "01"
# config 0x3a "spc" ?
########## stg ##########
# RATOC REX-5536, Melco IFC-SC
card "1195 RATOC System Inc." "REX5536 SCSI2 CARD"
config auto "stg" ? 0
# Future Domain SCSI2GO
card "Future Domain Corporation" "SCSI PCMCIA Credit Card Controller"
config auto "stg" ?
# IBM SCSI PCMCIA Card
card "IBM Corp." "SCSI PCMCIA Card"
config auto "stg" ?
# RATOC REX-5536AM, REX-9836A, ICM PSC-2401 SCSI
# There's a buggy revision of this card which has broken CIS tupples. # If
you can't use this card, change config entry from `auto' to
# `default' and try the point enabler. (for example,
# type "pccardc enabler 0 stg0 -a 0x4140 -i 5" from root command prompt)
card "PCMCIA SCSI MBH10404" "01"
# config default "stg" ?
config auto "stg" ?
logstr "RATOC REX-5536AM SCSI"
# RATOC REX-5536M
card "PCMCIA SCSI2 CARD" "01"
config auto "stg" ? 0
logstr "RATOC REX-5536M SCSI"
########## wlp ##########
# XXX NOT SUPPORTED YET
# AT&T GIS Wavelan PCMCIA
# If you want to use Japanese version, uncomment the second config # line and
comment-out the first line. #card "AT&T" "WaveLAN/PCMCIA"
# config default "wlp" ? # US version (915MHz)
## config default "wlp" ? 0x01 # Japanese version (2.4GHz)
## ether wavelan
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# XXX NOT SUPPORTED YET
# Digital RoamAbout
#card "Digital" "RoamAbout/DS"
# config auto "wlp" ?
## ether wavelan
# insert /usr/sbin/wlpconfig -i wlp0 -w 0xaaaa
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# XXX NOT SUPPORTED YET
# Lucent Wavelan
#card "Lucent Technologies" "WaveLAN/PCMCIA"
# config default "wlp" ?
# ether wavelan
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# XXX NOT SUPPORTED YET
# NCR Wavelan PCMCIA
# If you want to use Japanese version, uncomment the second config # line and
comment-out the first line. #card "NCR" "WaveLAN/PCMCIA"
# config default "wlp" ? # US version (915MHz)
## config default "wlp" ? 0x01 # Japanese version (2.4GHz)
# ether wavelan
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
########## wi ##########
# OEM ID 0x5 unlabelled PRISM2.5 card
card " " "IEEE 802.11 Wireless LAN/PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# 3com 3crwe737A AirConnect Wireless LAN PC Card
card "3Com" "3CRWE737A AirConnect Wireless LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Accton airDirect WN3301
card "Accton" "IEEE802.11 PC Card Adapter"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Actiontec PRISM wireless
card "ACTIONTEC" "PRISM Wireless LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Addtron AWP-100
card "Addtron" "AWP-100 Wireless PCMCIA"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ADLINK340APC
card "ADTEC" "ADLINK/340C"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Home Wireless Networks
card "AirWay" "802.11 Adapter (PCMCIA)"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Allied Telesis WR211PCM
card "Allied Telesis K.K." "WR211PCM"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Avaya Wireless PC Card
card "Avaya Communication" "Avaya Wireless PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Belkin wireless card
card "Belkin" "11Mbps Wireless Notebook Network Adapter"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# BreezeNET
card "BreezeNET" "PC-DS.11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Buffalo WLI-CF-S11G
card "BUFFALO" "WLI-CF-S11G"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Melco Airconnect 3.3V version
card "BUFFALO" "WLI-PCM-S11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Melco Airconnect (128bit WEP)
card "BUFFALO" "WLI-PCM-L11G"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Cabletron RoamAbout, WaveLAN/IEEE clone
card "Cabletron" "RoamAbout 802.11 DS"
config 0x1 "wi" ?
# config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Compaq WL100
card "Compaq" "WL100_11Mbps_Wireless_PC_Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Compaq WL110
card "Compaq" "Compaq WL110 PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Compaq WL200
card "Compaq" "WL200_11Mbps_Wireless_PCI_Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Compaq WL200 (might be wrong)
card "Compaq" "Compaq WL200_11Mbps_Wireless_PCI_Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Corega KK Wireless LAN PCC-11
card "corega K.K." "Wireless LAN PCC-11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Corega KK Wireless LAN PCCA-11
card "corega K.K." "Wireless LAN PCCA-11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Corega KK Wireless LAN PCCB-11
card "corega_K.K." "Wireless_LAN_PCCB-11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Corega KK Wireless LAN PCCL-11
card "corega" "WL PCCL-11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# D Link DWL-650 11Mbps WLAN Card
card "D" "Link DWL-650 11Mbps WLAN Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# DLink Air DWL-660 Wireless PC Card
card "D-Link" "D-Link Air DWL-660 Wireless PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Dell TrueMobile (OEMed Lucent WaveLAN/IEEE)
card "Dell" "TrueMobile 1150 Series PC Card"
config 0x1 "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Air at Hawk/LD-WL11/PCC (0.7.5)
card "ELECOM" "Air at Hark/LD-WL11/PCC"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELECOM Air at Hawk/LD-WL11/PCC (0.7.6 and later)
card "ELECOM" "Air at Hawk/LD-WL11/PCC"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ELSA Air Lancer
card "ELSA" "AirLancer MC-11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# PLANEX GeoWave/GW-NS11S
card "Geowave" "GW-NS11S"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys Instant Wireless WPC11
card "/Instant Wireless */" " Network PC CARD"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Intel PRO/Wireless 2011 LAN PC Card
card "Intel" "PRO/Wireless 2011 LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ICOM SL-1100
card "ICOM" "SL-1100"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Farallon Skyline 11Mbps Wireless
card "INTERSIL" "HFA384x/IEEE"
config 0x1 "wi" ?
# config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# IO Data WN-B11/PCM
card "IO DATA" "WNB11PCM"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# IBM's rebadged Lucent WaveLAN/IEEE. The FCC IDs are identical to # those
for the Lucent card, so presumably everything else is as well. card "IBM
Corporation" "IBM High Rate Wireless LAN PC Card"
config 0x1 "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Lucent WaveLAN/IEEE
card "Lucent Technologies" "WaveLAN/IEEE"
config 0x1 "wi" ?
# config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Melco Airconnect
card "MELCO" "WLI-PCM-L11"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# nanospeed card of some flavor.
card "NANOSPEED" "HFA384x/IEEE"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NCR WaveLAN/IEEE
card "NCR" "WaveLAN/IEEE"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NEC Wireless Card CMZ-RT-WP
card "NEC" "Wireless Card CMZ-RT-WP"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NEC WL11C (PC-WL/11C)
card "NEC Aterm" "WL11C (PC-WL/11C)"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NEC Corporation PK-WL001
card "NEC Corporation" "Wireless PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Netgear MA401
card "NETGEAR MA401 Wireless PC" "Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Netgear MA401RA
card "NETGEAR MA401RA Wireless PC" "Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Nortel eMobility
card "Nortel Networks" "emobility 802.11 Wireless LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# NTT-ME SS-LAN CARD MN128
card "NTT-ME" "11Mbps Wireless LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Generic PRISM2.5 card
card "PCMCIA" "11M WLAN Card v2.5"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# PLANEX GeoWave/GW-NS110
card "PLANEX" "GeoWave/GW-NS110"
config 0x1 "wi" ?
# config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# PLANEX GW-NS11H
card "PLANEX" "GW-NS11H Wireless LAN PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Proxim Harmony
card "PROXIM" "Harmony 802.11b/LAN PC CARD"
config 0x1 "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Proxim RangeLAN-DS (OEM of Zcommax - Prism2 card)
card "PROXIM" "RangeLAN-DS/LAN PC CARD"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# SAMSUNG SWL-2000P PCI Card
card "SAMSUNG" "11Mbps WLAN PCI Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# SMC's SMC2632W (also matches the 3.3V SMC2602W)
card "SMC" "SMC2632W"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Sony PCWA-C100 WaveLAN
card "Sony Corporation" "PCWA-C100"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# German Telekom T-Sinus 130card, unknown original manufactor card "T-
Sinus" "130card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# TDK LAK-CD011WL
card "TDK" "LAK-CD011WL for Wireless LAN"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Linksys Instant Wireless WPC11 v2.5
card "The Linksys Group, Inc." "Instant Wireless Network PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Toshibas wireless lan card
card "TOSHIBA" "Wireless LAN Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# U.S. Robotics Wireless Card 2410
card "U.S. Robotics" "IEEE 802.11b PC-CARD"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Taiwanese Blue Concentric Circle CF Wireless LAN Model WL-379F # This is a
card sold in Taiwan. card "Wireless LAN" "11Mbps PC Card"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# YIS YWL-11B
card "YIS Corp." "YWL-11b"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# ZoomAir 802.11
card "ZoomAir 11Mbps High" "Rate wireless Networking"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
########## xe ##########
# Accton EN2226/Fast EtherCard (16-bit verison)
card "Accton" "Fast EtherCard-16"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Compaq Netelligent 10/100 PC Card
card "Compaq" "Netelligent 10/100 PC Card"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Intel EtherExpress PRO/100 Mobile Adapter (16-bit verison)
card "Intel" "EtherExpress(TM) PRO/100 PC Card Mobile Adapter16"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# XXX NOT SURE SUPPORTED
# Toshiba 10/100 Ethernet PC Card IPC5008A
#card "Toshiba" "10/100 Ethernet PC Card"
# config auto "xe" ?
## cardio 0x300 0x10
# iosize 16
# insert /etc/pccard_ether $device start
# remove /etc/pccard_ether $device stop
# Xircom 10/100 Network PC Card
card "Xircom" "10/100 Network PC Card"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom Realport card + modem
card "Xircom" "16-bit Ethernet + Modem 56"
config 0x27 "xe" ?
# config auto "sio" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom CreditCard Ethernet CE3-10/100
card "Xircom" "CreditCard 10/100"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom CreditCard Ethernet Adaptor IIps (PS-CE2-10)
card "Xircom" "CreditCard 10Base-T"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom CreditCard Ethernet 10/100 + modem (Ethernet part) (CEM56)
card "Xircom" "CreditCard Ethernet 10/100 + Modem 56"
config 0x27 "xe" ?
# config auto "sio" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# Xircom RE-10
card "Xircom" "Ethernet Adapter"
config auto "xe" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
# -------------------------------------------------------------------
#
# "Wildcard" entries
#
# -------------------------------------------------------------------
# GENERIC PCMCIA modem
generic serial
config auto "sio" ?
# reset 100 # default
# reset 1000 # safety reset time
reset 10000 # for unstable cards
logstr "GENERIC PCMCIA modem"
# GENERIC Flash ATA / ATA HDD
generic fixed_disk
config 0x1 "ata" ?
logstr "GENERIC Flash ATA / ATA HDD"
On Mon, 04 Aug 2003 16:02:29 -0600 (MDT), M. Warner Losh wrote
> OLDCARD or NEWCARD?
>
> Warner
More information about the freebsd-mobile
mailing list