IBM X24 and PCMCIA

[Lutz Bichler]

On Thursday 31 July 2003 19:58, Kevin Oberman wrote:
> You probably need to add:
> hw.cbb.start_memory="0x20000000"
> to /boot/loader.conf. You might also need
> hw.pci.allow_unsupported_io_range="1" and
> hw.ata.atapi_dma="1"
> (The last is not related to this problem, but is important if you want
> to get decent performance from a CD reader.)
>
> Use NEWCARD. I am guessing that you meant pccardd on the fatal
> message. If that's the case, don't worry on NEWCARD as pccardd is not
> used with NEWCARD. You do still need pccard_enable="YES" in rc.config.
>
> If you still can't get things working, be sure to include your dmesg
> in further inquiries.

Hi,

i have done the things you suggested but it still does not work. I have the 
demsg attached. The drive is a Hitachi DVD-ROM, Model No. GDR-8081N in an IBM 
Portable Drive Bay 2000. This combination worked under 4.8 using the PCMCIA 
adapter. Alternatively i can attach the drive using USB. But then i get 

umass0: USB to IDE USB to IDE, rev 1.10/2.60, addr 2
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): error code 64 at block no. 134217984 (decimal)
(probe0:umass-sim0:0:0:0): No Recovery Action Needed


and things do not work. Any more ideas what i could try?

Lutz
-------------- next part --------------
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE #52: Thu Jul 31 19:46:51 CEST 2003
    lutz at chrysaor.informatik.unibw-muenchen.de:/usr/obj/usr/src/sys/CHRYSAOR
Preloaded elf kernel "/boot/kernel/kernel" at 0xc048c000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc048c244.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 1129574146 Hz
CPU: Intel(R) Pentium(R) III Mobile CPU      1133MHz (1129.57-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 267845632 (255 MB)
avail memory = 255164416 (243 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <IBM    TP-1D   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 14 entries at 0xc00fdeb0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.FDC_._INI] (Node 0xc25f3ac0), AE_NOT_EXIST
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__._INI] (Node 0xc25ec8c0), AE_NOT_EXIST
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> port 0x530-0x537 on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
    ACPI-1287: *** Error: Method execution failed [\\_SB_.LID_._PSW] (Node 0xc0eb7480), AE_NOT_EXIST
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82830 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
drm0: <ATI Radeon LY Mobility M6> port 0x3000-0x30ff mem 0xc0100000-0xc010ffff,0xe0000000-0xe7ffffff irq 3 at device 0.0 on pci1
info: [drm] AGP at 0xd0000000 256MB
info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 3 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f irq 5 at device 29.2 on pci0
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 3 at device 3.0 on pci2
start (50000000) < sc->membase (c0200000)
start (50000000) < sc->pmembase (e8000000)
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <RF5C476 PCI-CardBus Bridge> mem 0x50100000-0x50100fff irq 4 at device 3.1 on pci2
start (50100000) < sc->membase (c0200000)
start (50100000) < sc->pmembase (e8000000)
pccard1: <16-bit PCCard bus> on cbb1
pci2: <network> at device 5.0 (no driver attached)
fxp0: <Intel 82801CAM (ICH3) Pro/100 VE Ethernet> port 0x8000-0x803f mem 0xc0200000-0xc0200fff irq 10 at device 8.0 on pci2
fxp0: Ethernet address 00:d0:59:cc:fc:e8
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel 82801CA (ICH3)> port 0x18c0-0x18ff,0x1c00-0x1cff irq 4 at device 31.5 on pci0
pcm0: <Cirrus Logic CS4299 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 8250 or not responding
ppc0 port 0x3bc-0x3c3 irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
orm0: <Option ROMs> at iomem 0xe0000-0xeffff,0xdc000-0xdffff,0xcd000-0xcdfff,0xcc000-0xccfff,0xc0000-0xcbfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acpi_cmbat0: battery initialization start
acpi_acad0: acline initialization start
ad0: 28615MB <HITACHI_DK23DA-30B> [62016/15/63] at ata0-master UDMA100
acpi_ec0: EcRead: Failed waiting for EC to send data.
    ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
    ACPI-1287: *** Error: Method execution failed [\\_SB_.PCI0.LPC_.EC__.AC__._PSR] (Node 0xc25ef140), AE_ERROR
acpi_acad0: acline initialization done, tried 1 times
acpi_ec0: EcWaitEventIntr called without EC lock!
acpi_cmbat0: battery initialization done, tried 1 times
Mounting root from ufs:/dev/ad0s1a
acpi_acad0: On Line
WARNING: driver "rtc" used unreserved major device number 202
WARNING: driver "vmmon" used unreserved major device number 200
/dev/vmmon: Module vmmon: registered with major=200 minor=0 tag=$Name: build-570+ $
/dev/vmmon: Module vmmon: initialized
start (20000000) < sc->membase (c0200000)
end (ffffffff) > sc->memlimit (cfffffff)
start (20000000) < sc->pmembase (e8000000)
end (ffffffff) > sc->pmemlimit (cfffffff)
start (20000000) < sc->membase (c0200000)
end (ffffffff) > sc->memlimit (cfffffff)
start (20000000) < sc->pmembase (e8000000)
end (ffffffff) > sc->pmemlimit (cfffffff)
pccard0: <unknown card> (manufacturer=0xffffffff, product=0xffffffff) at function 0
pccard0:    CIS info: PCMCIA, IDE CARD, F1