onion omega2+
Stanislav Galabov
sgalabov at gmail.com
Wed May 10 09:38:47 UTC 2017
Hi Mike,
Alexandr is right, what I described should work for binary kernels and not for ELF ones. I somehow was of the impression that you were using binary. Please try the same with binary kernel per Alexandr's suggestion in an earlier post...
Best wishes
Stanislav
> On May 10, 2017, at 12:31, Mike Wolman <mike at wolman.co.uk> wrote:
>
> Hi Stanislav,
>
> Just rebuild kernel with the original dtsi and made a new uImage with:
>
>
> [mike at f64-current ~/omega2/tftpboot]$ mkimage -A mips -C none -O linux -T kernel -a 0x80001100 -e 0x80001100 -n "FreeBSD" -d kernel.MT7628_FDT kernel.MT7628_FDT.uImage
> Image Name: FreeBSD
> Created: Wed May 10 10:10:37 2017
> Image Type: MIPS Linux Kernel Image (uncompressed)
> Data Size: 5654760 Bytes = 5522.23 kB = 5.39 MB
> Load Address: 80001100
> Entry Point: 80001100
>
>
> On the Omega:
>
>
> Omega2 # fatload usb 0:1 0x80800000 kernel.MT7628_FDT.uImage
> *
> *
> Reading file "kernel.MT7628_FDT.uImage"
> *
> **
> ******
> ...
> ****
> *
> FAT: 5654824 Bytes read
> Omega2 # bootm 0x80800000
> ## Booting image at 80800000 ...
> Image Name: FreeBSD
> Image Type: MIPS Linux Kernel Image (uncompressed)
> Data Size: 5654760 Bytes = 5.4 MB
> Load Address: 80001100
> Entry Point: 80001100
> Verifying Checksum ... OK
> OK
> No initrd
> ## Transferring control to Linux (at address 80001100) ...
> ## Giving linux memsize in MB, 128
>
> Starting kernel ...
>
>
> And again nothing more, I also tried one with a Load Address 80000000 but that hasnt worked either.
>
>
> In case this is of any use - when linux boots this is what the console looks like:
>
>
> Boot Linux from Flash NO RESET PRESSED.
> ## Booting image at bc050000 ...
> Image Name: MIPS LEDE Linux-4.4.32
> Image Type: MIPS Linux Kernel Image (lzma compressed)
> Data Size: 1345538 Bytes = 1.3 MB
> Load Address: 80000000
> Entry Point: 80000000
> Verifying Checksum ... OK
> Uncompressing Kernel Image ... OK
> No initrd
> ## Transferring control to Linux (at address 80000000) ...
> ## Giving linux memsize in MB, 128
>
> Starting kernel ...
>
> [ 0.000000] Linux version 4.4.32 (root at 2272a3272872) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2292+1) ) #0 Wed Nov 23 00:21:47 2016
> [ 0.000000] Board has DDR2
> [ 0.000000] Analog PMU set to hw control
> [ 0.000000] Digital PMU set to hw control
> [ 0.000000] SoC Type: MediaTek MT7688 ver:1 eco:2
> [ 0.000000] bootconsole [early0] enabled
> [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
> [ 0.000000] MIPS: machine is Onion Omega2+
> [ 0.000000] Determined physical RAM map:
> [ 0.000000] memory: 08000000 @ 00000000 (usable)
> [ 0.000000] Initrd not found or empty - disabling initrd
> [ 0.000000] Zone ranges:
> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
> [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
> [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
> [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
> [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> [ 0.000000] Writing ErrCtl register=00022002
> [ 0.000000] Readback ErrCtl register=00022002
> [ 0.000000] Memory: 125488K/131072K available (3103K kernel code, 141K rwdata, 752K rodata, 156K init, 196K bss, 5584K reserved, 0K cma-reserved)
> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] NR_IRQS:256
> [ 0.000000] intc: using register map from devicetree
> [ 0.000000] CPU Clock: 580MHz
> [ 0.000000] clocksource_probe: no matching clocksources found
> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
> [ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
> [ 0.007522] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
> [ 0.070037] pid_max: default: 32768 minimum: 301
> [ 0.074638] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.080979] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.094407] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.104062] pinctrl core: initialized pinctrl subsystem
> [ 0.109786] NET: Registered protocol family 16
> [ 0.135691] mt7621_gpio 10000600.gpio: registering 32 gpios
> [ 0.141166] mt7621_gpio 10000600.gpio: registering 32 gpios
> [ 0.146653] mt7621_gpio 10000600.gpio: registering 32 gpios
> [ 0.153211] i2c-mt7621 10000900.i2c: clock 100KHz, re-start not support
> [ 0.161026] clocksource: Switched to clocksource MIPS
> [ 0.167442] NET: Registered protocol family 2
> [ 0.172577] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.179269] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.185449] TCP: Hash tables configured (established 1024 bind 1024)
> [ 0.191652] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.197255] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.203624] NET: Registered protocol family 1
> [ 0.214036] futex hash table entries: 256 (order: -1, 3072 bytes)
> [ 0.219960] Crashlog allocated RAM at address 0x3f00000
> [ 0.240245] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 0.245900] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [ 0.258137] io scheduler noop registered
> [ 0.261942] io scheduler deadline registered (default)
> [ 0.268315] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> [ 0.276011] console [ttyS0] disabled
> [ 0.279438] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
> [ 0.288217] console [ttyS0] enabled
> [ 0.288217] console [ttyS0] enabled
> [ 0.295211] bootconsole [early0] disabled
> [ 0.295211] bootconsole [early0] disabled
> [ 0.303969] 10000d00.uart1: ttyS1 at MMIO 0x10000d00 (irq = 29, base_baud = 2500000) is a 16550A
> [ 0.313561] 10000e00.uart2: ttyS2 at MMIO 0x10000e00 (irq = 30, base_baud = 2500000) is a 16550A
> [ 0.324283] spi-mt7621 10000b00.spi: sys_freq: 193333333
> [ 0.334382] m25p80 spi32766.0: using chunked io (size=31)
> [ 0.339882] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
> [ 0.345451] 4 ofpart partitions found on MTD device spi32766.0
> [ 0.351378] Creating 4 MTD partitions on "spi32766.0":
> [ 0.356594] 0x000000000000-0x000000030000 : "u-boot"
> [ 0.363407] 0x000000030000-0x000000040000 : "u-boot-env"
> [ 0.370634] 0x000000040000-0x000000050000 : "factory"
> [ 0.377673] 0x000000050000-0x000002000000 : "firmware"
> [ 0.425492] 2 uimage-fw partitions found on MTD device firmware
> [ 0.431550] 0x000000050000-0x000000198842 : "kernel"
> [ 0.438242] 0x000000198842-0x000002000000 : "rootfs"
> [ 0.445146] mtd: device 5 (rootfs) set to be root filesystem
> [ 0.450960] 1 squashfs-split partitions found on MTD device rootfs
> [ 0.457297] 0x0000006b0000-0x000002000000 : "rootfs_data"
> [ 0.474397] rt3050-esw 10110000.esw: link changed 0x00
> [ 0.482079] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
> [ 0.490683] i2c /dev entries driver
> [ 0.494876] mt7621_wdt 10000120.watchdog: Initialized
> [ 0.500240] MTK MSDC device init.
> [ 0.541172] mtk-sd: MediaTek MT6575 MSDC Driver
> [ 0.547206] NET: Registered protocol family 10
> [ 0.555832] NET: Registered protocol family 17
> [ 0.560430] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
> [ 0.573286] 8021q: 802.1Q VLAN Support v1.8
> [ 0.579808] mtk-linkit bootstrap: Version :
> [ 0.584309] mtk-linkit bootstrap: Revision :
> [ 0.593456] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
> [ 0.601535] Freeing unused kernel memory: 156K (803e9000 - 80410000)
> [ 1.630140] init: Console is alive
> ...
> more linux kernel messages.
>
>
>> On 10/05/2017 08:16, Stanislav Galabov wrote:
>> Hi Mike,
>>
>> Please try setting both the Load Address and the Entry Point to the same value as you see as Entry point address by using 'readelf -h’ and try booting again.
>> In your case this would seem to be 0x80001100.
>>
>> Please leave all dts/dtsi files unchanged (as they originally were) for now.
>>
>> Best wishes,
>> Stanislav
>>
>>> On May 10, 2017, at 04:33, Mike Wolman <mike at wolman.co.uk> wrote:
>>>
>>>
>>> I have just tried with clock-frequency change in the 3 places it appears in mt7628an.dtsi
>>>
>>> But again some thing:
>>>
>>> Omega2 # bootm 0x80800000
>>> ## Booting image at 80800000 ...
>>> Image Name: FreeBSD
>>> Image Type: MIPS Linux Kernel Image (uncompressed)
>>> Data Size: 5654760 Bytes = 5.4 MB
>>> Load Address: 80001000
>>> Entry Point: 80001100
>>> Verifying Checksum ... OK
>>> OK
>>> No initrd
>>> ## Transferring control to Linux (at address 80001100) ...
>>> ## Giving linux memsize in MB, 128
>>>
>>> Starting kernel ...
>>>
>>>
>>> Note: When building kernel i see:
>>>
>>> --------------------------------------------------------------
>>>>>> stage 3.1: building everything
>>> --------------------------------------------------------------
>>> converting OMEGA2P.dts -> /usr/home/mike/omega2/obj/mipsel_ap/mips.mipsel/usr/home/mike/omega2/src/sys/MT7628_FDT/OMEGA2P.dtb
>>> /usr/home/mike/omega2/obj/mipsel_ap/mips.mipsel/usr/home/mike/omega2/src/sys/MT7628_FDT/OMEGA2P.dtb: Warning (unit_address_vs_reg): Node /cpus/cpu at 0 has a unit name, but no reg property
>>> /usr/home/mike/omega2/obj/mipsel_ap/mips.mipsel/usr/home/mike/omega2/src/sys/MT7628_FDT/OMEGA2P.dtb: Warning (unit_address_vs_reg): Node /cpuintc at 0 has a unit name, but no reg property
>>> /usr/home/mike/omega2/obj/mipsel_ap/mips.mipsel/usr/home/mike/omega2/src/sys/MT7628_FDT/OMEGA2P.dtb: Warning (unit_address_vs_reg): Node /pcie at 10140000/pcie-bridge has a reg or ranges property, but no unit name
>>>
>>> Are these just warnings which can be ignored or could they be part of the problem?
>>>
>>>
>>>
>>>> On 10/05/2017 01:50, Mori Hiroki wrote:
>>>> Hi mike
>>>>
>>>> I last idea is uartlite clock-frequency miss.
>>>>
>>>> clock-frequency = <50000000>;
>>>>
>>>> But I don't know correct value.
>>>>
>>>>
>>>>
>>>> ----- Original Message -----
>>>>> From: Mike Wolman <mike at wolman.co.uk>
>>>>> To: Mori Hiroki <yamori813 at yahoo.co.jp>; Aleksandr Rybalko <ray at ddteam.net>
>>>>> Cc: "freebsd-mips at freebsd.org" <freebsd-mips at freebsd.org>
>>>>> Date: 2017/5/10, Wed 09:01
>>>>> Subject: Re: onion omega2+
>>>>>
>>>>>
>>>>> The new kernel with
>>>>>
>>>>> device uart_ns8250
>>>>>
>>>>> didnt work
>>>>>
>>>>>> On 10/05/2017 00:05, Mori Hiroki wrote:
>>>>>> Hi Mike.
>>>>>>
>>>>>> I seem load address is good.
>>>>>>
>>>>>> I check mt7628an.dtsi file.
>>>>>>
>>>>>> This file uart entry is
>>>>>>
>>>>>> uartlite: uartlite at c00 {
>>>>>> compatible = "ns16550a";
>>>>>> In this case you must add uart_ns8250 device to kernel configuration.
>>> _______________________________________________
>>> freebsd-mips at freebsd.org mailing list
>>> https://lists.freebsd.org/mailman/listinfo/freebsd-mips
>>> To unsubscribe, send any mail to "freebsd-mips-unsubscribe at freebsd.org"
>
More information about the freebsd-mips
mailing list