i386/59895: system hangs from disk IO errors
Derek Ragona
derek at computinginnovations.com
Mon Dec 1 23:40:25 PST 2003
>Number: 59895
>Category: i386
>Synopsis: system hangs from disk IO errors
>Confidential: no
>Severity: critical
>Priority: high
>Responsible: freebsd-i386
>State: open
>Quarter:
>Keywords:
>Date-Required:
>Class: sw-bug
>Submitter-Id: current-users
>Arrival-Date: Mon Dec 01 23:40:08 PST 2003
>Closed-Date:
>Last-Modified:
>Originator: Derek Ragona
>Release: FreeBSD 5.2-BETA i386
>Organization:
Computing Innovations
>Environment:
System: FreeBSD barney.computinginnovations.com 5.2-BETA FreeBSD 5.2-BETA #5: Sun Nov 30 20:09:49 CST 2003 root at barney.computinginnovations.com:/usr/obj/usr/src/sys/GENERIC i386
i386, FreeBSD 5.2-BETA, SATA disk using a SiI 3112 SATA150 controller, using standard GENERIC kernel and system
>Description:
System hangs on any large amount of disk IO. The system will hang, not allowing any user input, no choice but to reset the system. The system will usually have a DMA_Write error, and some interupt problems, finally ending with these error messages scrolling on the console:
ad4: timeout sending command=ca
ad4: timeout sending command=ca
The precise hardware I have is an Adaptec SATA 1210SA RAID controller, in non-RAID mode having only one disk attached. The hard disk is a new Maxtor 6Y120M0 120 GB drive. The drive has FreeBSD partioned to about 1/2 the capacity, in 3 slices 5 GB /, 47 GB /usr, 5 GB swap.
This is the generic system and kernel, not customized at all.
>How-To-Repeat:
I usually just try to cvsup and rebuild the system in multiuser. There are no other users using this server.
cvsup to current
make buildworld
make kernel
reboot
mergemaster -p
make installworld
mergemaster
The system usually breaks down in the make buildworld, or in the make kernel, or in the make installworld. I had the 11/29 snapshot release break on an upgrade install doing fsck on /usr.
>Fix:
None that I have found. This SATA controller is getting into wider use on motherboards as well as add-on cards like I use. I am not the only one experiencing these interrupt and DMA problems.
--- dmesg.today begins here ---
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-BETA-20031129-JPSNAP #0: Sat Nov 29 02:47:57 GMT 2003
root at ushi.jp.freebsd.org:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a78000.
ACPI APIC Table: <INTEL D845GBV2>
Calibrating clock(s) ... i8254 clock: 1193135 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1699951844 Hz
CPU: Intel(R) Celeron(R) CPU 1.70GHz (1699.95-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf13 Stepping = 3
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
real memory = 1071906816 (1022 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c29000 - 0x000000003ec21fff, 1040158720 bytes (253945 pages)
avail memory = 1031774208 (983 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f4990
pnpbios: Entry = f0000:4fca Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
MADT: Found IO APIC ID 1, Vector 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
lapic0: Routing NMI -> LINT1
MADT: Ignoring local NMI routed to ACPI CPU 2
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: active-hi
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
acpi0: <INTEL D845GBV2> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000094
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25608086)
pcibios: BIOS version 2.10
Using $PIR table, 11 entries at 0xc00f4860
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 1 8 A 0x68 3 4 5 6 7 9 10 11 12 14 15
embedded 0 1 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 1 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 1 1 0 A 0x69 3 4 5 6 7 9 10 11 12 14 15
slot 1 1 0 B 0x6a 3 4 5 6 7 9 10 11 12 14 15
slot 1 1 0 C 0x6b 3 4 5 6 7 9 10 11 12 14 15
slot 1 1 0 D 0x68 3 4 5 6 7 9 10 11 12 14 15
slot 2 1 1 A 0x6a 3 4 5 6 7 9 10 11 12 14 15
slot 2 1 1 B 0x69 3 4 5 6 7 9 10 11 12 14 15
slot 2 1 1 C 0x68 3 4 5 6 7 9 10 11 12 14 15
slot 2 1 1 D 0x6b 3 4 5 6 7 9 10 11 12 14 15
slot 3 1 2 A 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 3 1 2 B 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 3 1 2 C 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 3 1 2 D 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 4 1 3 A 0x63 3 4 5 6 7 9 10 11 12 14 15
slot 4 1 3 B 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 4 1 3 C 0x69 3 4 5 6 7 9 10 11 12 14 15
slot 4 1 3 D 0x6a 3 4 5 6 7 9 10 11 12 14 15
slot 5 1 4 A 0x61 3 4 5 6 7 9 10 11 12 14 15
slot 5 1 4 B 0x6b 3 4 5 6 7 9 10 11 12 14 15
slot 5 1 4 C 0x60 3 4 5 6 7 9 10 11 12 14 15
slot 5 1 4 D 0x68 3 4 5 6 7 9 10 11 12 14 15
slot 6 1 5 A 0x62 3 4 5 6 7 9 10 11 12 14 15
slot 6 1 5 B 0x68 3 4 5 6 7 9 10 11 12 14 15
slot 6 1 5 C 0x6a 3 4 5 6 7 9 10 11 12 14 15
slot 6 1 5 D 0x69 3 4 5 6 7 9 10 11 12 14 15
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 4, width = 0
ACPI timer looks GOOD min = 4, max = 5, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x8086, dev=0x2560, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 3, range 32, base f0000000, size 27, enabled
map[14]: type 1, range 32, base ffa80000, size 19, enabled
pcib0: matched entry for 0.2.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x2562, revid=0x03
bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=16
powerspec 1 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000e800, size 5, enabled
pcib0: matched entry for 0.29.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x24c2, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=16
map[20]: type 4, range 32, base 0000e880, size 5, enabled
pcib0: matched entry for 0.29.INTB (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x24c4, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=19
map[20]: type 4, range 32, base 0000ec00, size 5, enabled
pcib0: matched entry for 0.29.INTC (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x24c7, revid=0x02
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=18
map[10]: type 1, range 32, base ffa7fc00, size 10, enabled
pcib0: matched entry for 0.29.INTD (source )
pcib0: device is hardwired to IRQ 23
found-> vendor=0x8086, dev=0x24cd, revid=0x02
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=23
powerspec 2 supports D0 D3 current D0
found-> vendor=0x8086, dev=0x244e, revid=0x82
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x8080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x02 (500 ns)
found-> vendor=0x8086, dev=0x24c0, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 00000000, size 3, enabled
map[14]: type 4, range 32, base 00000000, size 2, enabled
map[18]: type 4, range 32, base 00000000, size 3, enabled
map[1c]: type 4, range 32, base 00000000, size 2, enabled
map[20]: type 4, range 32, base 0000ffa0, size 4, enabled
found-> vendor=0x8086, dev=0x24cb, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 0000e000, size 5, enabled
pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x24c3, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=17
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 4, range 32, base 0000e080, size 6, enabled
map[18]: type 1, range 32, base ffa7f800, size 9, enabled
map[1c]: type 1, range 32, base ffa7f400, size 8, enabled
pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x24c5, revid=0x02
bus=0, slot=31, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=17
powerspec 2 supports D0 D3 current D0
agp0: <Intel 82845G (845G GMCH) SVGA controller> mem 0xffa80000-0xffafffff,0xf0000000-0xf7ffffff irq 16 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xe800-0xe81f irq 16 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xe880-0xe89f irq 19 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xec00-0xec1f irq 18 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xff700000-0xff8fffff
pcib1: prefetched decode 0xe6a00000-0xe6afffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 4, range 32, base 0000dc00, size 3, enabled
map[14]: type 4, range 32, base 0000d880, size 2, enabled
map[18]: type 4, range 32, base 0000d800, size 3, enabled
map[1c]: type 4, range 32, base 0000d480, size 2, enabled
map[20]: type 4, range 32, base 0000d400, size 4, enabled
map[24]: type 1, range 32, base ff8ffc00, size 9, enabled
pcib1: matched entry for 1.5.INTA (source )
pcib1: device is hardwired to IRQ 18
found-> vendor=0x1095, dev=0x0240, revid=0x02
bus=1, slot=5, func=0
class=01-04-01, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=18
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ff8fe000, size 12, enabled
map[14]: type 4, range 32, base 0000d080, size 6, enabled
pcib1: matched entry for 1.8.INTA (source )
pcib1: device is hardwired to IRQ 20
found-> vendor=0x8086, dev=0x1039, revid=0x82
bus=1, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
atapci0: <SiI 3112 SATA150 controller> port 0xd400-0xd40f,0xd480-0xd483,0xd800-0xd807,0xd880-0xd883,0xdc00-0xdc07 mem 0xff8ffc00-0xff8ffdff irq 18 at device 5.0 on pci1
pcib1: device atapci0 requested decoded I/O range 0xd400-0xd40f
atapci0: [MPSAFE]
pcib1: device atapci0 requested decoded memory range 0xff8ffc00-0xff8ffdff
ata2: reset tp1 mask=01 ostat0=50 ostat1=00
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=01 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: at 0xff8ffc00 on atapci0
ata2: [MPSAFE]
ata3: reset tp1 mask=01 ostat0=7f ostat1=00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0xff err=0x00 lsb=0x00 msb=0x00
ata3: reset tp2 mask=00 stat0=ff stat1=00 devices=0x0
ata3: at 0xff8ffc00 on atapci0
ata3: [MPSAFE]
fxp0: <Intel 82801DB (ICH4) Pro/100 VE Ethernet> port 0xd080-0xd0bf mem 0xff8fe000-0xff8fefff irq 20 at device 8.0 on pci1
pcib1: device fxp0 requested decoded memory range 0xff8fe000-0xff8fefff
fxp0: using memory space register mapping
fxp0: Ethernet address 00:07:e9:59:e5:3c
fxp0: PCI IDs: 8086 1039 8086 3011 0082
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH4 UDMA100 controller> port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x01 lsb=0x7f msb=0x7f
ata0: reset tp2 mask=03 stat0=10 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci1
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci1
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
unknown: not probed (disabled)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xcb800-0xcf7ff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1699951844 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
ata0: spurious interrupt - status=0x50 error=0x00
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
ata0-master: setting PIO4 on Intel ICH4 chip
acd0: <TEAC CD-552E/VER 1.00> CDROM drive at ata0 as master
acd0: read 8958KB/s (8958KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata2-master: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
GEOM: create disk ad4 dp=0xc6b78860
ad4: <Maxtor 6Y120M0/YAR51BW0> ATA-7 disk at ata2-master
ad4: 117246MB (240121728 sectors), 238216 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA133
GEOM: new disk ad4
ar: FreeBSD check1 failed
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 12 (IRQ 12) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic0: routing intpin 20 (IRQ 20) to cluster 0
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:20482812
[1] f:00 typ:15 s(CHS):1023/255/63 e(CHS):1023/254/63 s:20482875 l:102414375
[2] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:122897250 l:117210240
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 10487199744 end 10487231999
GEOM: Configure ad4s2, start 10487232000 length 52436160000 end 62923391999
GEOM: Configure ad4s3, start 62923392000 length 60011642880 end 122935034879
MBREXT Slice 5 on ad4s2:
[0] f:00 typ:7 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:90124587
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:90124650 l:12289725
GEOM: Configure ad4s5, start 32256 length 46143788544 end 46143820799
MBREXT Slice 6 on ad4s2:
[0] f:00 typ:7 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:12289662
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s6, start 46143853056 length 6292306944 end 52436159999
GEOM: Configure ad4s3a, start 0 length 5368709120 end 5368709119
GEOM: Configure ad4s3b, start 5368709120 length 5368709120 end 10737418239
GEOM: Configure ad4s3c, start 0 length 60011642880 end 60011642879
GEOM: Configure ad4s3d, start 10737418240 length 49274224640 end 60011642879
Mounting root from ufs:/dev/ad4s3a
start_init: trying /sbin/init
--- dmesg.today ends here ---
>Release-Note:
>Audit-Trail:
>Unformatted:
More information about the freebsd-i386
mailing list