Raspberry PI zero USB - boot log

Wojciech Puchar wojtek at puchar.net
Fri Jan 10 14:05:03 UTC 2020


MMC:   mmc at 7e300000: 1
Loading Environment from FAT... In:    serial
Out:   vidconsole
Err:   vidconsole
Net:   No ethernet found.
starting USB...
Bus usb at 7e980000: scanning bus usb at 7e980000 for devices... 1 USB Device(s) found
        scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  2  1  0 
MMC Device 0 not found
no mmc device at slot 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
78Scanning disk mmc at 7e300000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
624336 bytes read in 83 ms (7.2 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
[?25hConsoles: EFI console 
|/-\    Reading loader env vars from /efi/freebsd/loader.env 
Setting currdev to disk0p1: 
|/-\|/FreeBSD/arm EFI loader, Revision 1.1

    Command line arguments: l
    EFI version: 2.80
    EFI Firmware: Das U-Boot (rev 8217.4096)
    Console: efi (0)
    Load Path: /efi\boot\bootarm.efi
    Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,MBR,0x90909090,0x800,0x36ad0c0) 
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,MBR,0x90909090,0x800,0x36ad0c0) 
Setting currdev to disk0p1: 
-\|/-\|/-\|/Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(2,MBR,0x90909090,0x36ad8c0,0x4c4b40) 
Setting currdev to disk0p2: 
-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\Loading /boot/defaults/loader.conf 
Loading /boot/device.hints 
|/-\|/-\|/-\|/-Loading /boot/loader.conf 
\|/-\|Loading /boot/loader.conf.local 
/-\|/-\|/-\|/-\|/-\|/-\|Loading kernel... 
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-/boot/kernel/kernel data=0x75a324+0x1edcdc \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/syms=[0x4+0xc2dd0-\|/-\+0x4+0xcc072|/-\|/-] 
Loading configured modules... 
\|/-\|/-\|/-\|//boot/kernel/umodem.ko text=0x2438 data=0x244+0x4 syms=[0x4+0xa00+0x4+0xaf6] 
loading required module 'ucom' 
-\|/-\|/-\|/-\|/-\|/-/boot/kernel/ucom.ko text=0x4390 data=0x3d4+0x838 \syms=[0x4+0xeb0+0x4+0xc2e] 
|/-\|/-\/boot/entropy size=0x1000

Hit [Enter] to boot immediately, or any other key for command prompt.
 Booting [/boot/kernel/kernel] in 1 second... Booting [/boot/kernel/kernel]... 
Using DTB provided by EFI at 0x7ef6000. 
Kernel entry at 0x14c00100... 
Kernel args: (null) 
|/-\|/---<<BOOT>>---
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.1-STABLE r356529 RPI-B arm
FreeBSD clang version 9.0.1 (git at github.com:llvm/llvm-project.git c1a0a213378a458fbea1a5c77b315c7dce08fd05) (based on LLVM 9.0.1)
VT: init without driver.
CPU: ARM ARM1176 r0p7 (ECO: 0x00000000)
CPU Features:
   Thumb, Security, VMSAv7
Optional instructions:
   UMULL, SMULL, MLA, SIMD(ext)
   16KB/32B 4-way instruction cache
   16KB/32B 4-way WB data cache
real memory  = 469757952 (447 MB)
avail memory = 446189568 (425 MB)
random: unblocking device.
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 19,20 on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16 on simplebus0
Checking root against raspberrypi,model-b
Checking root against brcm,bcm2835
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023 on simplebus0
bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f irq 17 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 18 on simplebus0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 21 on simplebus0
uart0: console (115200,n,8,1)
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 41,42 on simplebus0
usbus0 on bcm283x_dwcotg0
systimer0 mem 0x7e003000-0x7e003fff irq 43,44,45,46 on simplebus0
Event timer "BCM2835-3" frequency 1000000 Hz quality 1000
Timecounter "BCM2835-3" frequency 1000000 Hz quality 1000
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 48 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
vchiq0: <BCM2835 VCHIQ> mem 0x7e00b840-0x7e00b87b irq 52 on simplebus0
vchiq: local ver 8 (min 3), remote ver 8.
pcm0: <VCHIQ audio> on vchiq0
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
fb0: 656x416(656x416 at 0,0) 24bpp
fb0: fbswap: 1, pitch 1968, base 0x1eb33000, screen_size 818688
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
intc0: Stray irq 17 disabled
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG OTG Root HUB> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmcsd0: 32GB <SDHC SL32G 8.0 SN BB434268 MFG 06/2017 by 3 SD> at mmc0 50.0MHz/4bit/65535-block
Trying to mount root from ufs:/dev/ufs/rootfs [rw,noatime]...
Warning: no time-of-day clock registered, system time will not be set accurately
uhub0: 1 port with 1 removable, self powered
Setting hostuuid: d885de37-3299-11ea-b6c2-93a4fee15f62.
Setting hostid: 0xb6bb69d6.
Starting file system checks:
/dev/ufs/rootfs: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ufs/rootfs: clean, 444504 free (1048 frags, 55432 blocks, 0.2% fragmentation)
/dev/mmcsd0s1: FILESYSTEM CLEAN; SKIPPING CHECKS
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
Soft Float compatibility ldconfig path:
Setting hostname: rejestrator.
Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
lo0: link state changed to UP
Starting Network: lo0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
 	options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
 	inet6 ::1 prefixlen 128
 	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
 	inet 127.0.0.1 netmask 0xff000000
 	groups: lo
 	nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
add host 127.0.0.1: gateway lo0 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Starting syslogd.
Clearing /tmp (X related).
Updating motd:.
Mounting late filesystems:.
Configuring vt: blanktime.
Starting cron.

Fri Jan 10 14:58:38 CET 2020

FreeBSD/arm (rejestrator) (ttyu0)

login: root
Password:
Last login: Fri Jan 10 14:58:05 on ttyu0
FreeBSD 12.1-STABLE r356529 RPI-B

Welcome to FreeBSD!

Release Notes, Errata: https://www.FreeBSD.org/releases/
Security Advisories:   https://www.FreeBSD.org/security/
FreeBSD Handbook:      https://www.FreeBSD.org/handbook/
FreeBSD FAQ:           https://www.FreeBSD.org/faq/
Questions List: https://lists.FreeBSD.org/mailman/listinfo/freebsd-questions/
FreeBSD Forums:        https://forums.FreeBSD.org/

Documents installed with the system are in the /usr/local/share/doc/freebsd/
directory, or can be installed later with:  pkg install en-freebsd-doc
For other languages, replace "en" with a language code like de or fr.

Show the version of FreeBSD installed:  freebsd-version ; uname -a
Please include that output and any error messages when posting questions.
Introduction to manual pages:  man man
FreeBSD directory layout:      man hier

Edit /etc/motd to change this login announcement.
78(max 60 seconds) for system thread `bufspacedaemon-0' to stop... done
All buffers synced.
Uptime: 30s

The operating system has halted.
Please press any key to reboot.

~
[EOT]
[root at wojtek /tmp]# exit

Script done on Fri Jan 10 15:01:10 2020


More information about the freebsd-hackers mailing list