Problem with Broadcom 5704 B1 on amd64 6.2 release

[James Shank]

Dear Stefan,

Thanks for your help.  I've attached the information you requested.
In particular, here are the relevant sections of the dmesg output:

pcib5: <ACPI PCI-PCI bridge> at device 11.0 on pci8
pcib5:   secondary bus     10
pcib5:   subordinate bus   10
pcib5:   I/O decode        0xf000-0xfff
pcib5:   memory decode     0xde100000-0xde1fffff
pcib5:   prefetched decode 0xfff00000-0xfffff
pci10: <ACPI PCI bus> on pcib5
pci10: physical bus=10
found->	vendor=0x14e4, dev=0x1648, revid=0x10
	bus=10, slot=9, func=0
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	MSI supports 8 messages, 64 bit
	map[10]: type 1, range 64, base de100000, size 16, enabled
pcib5: memory: end (de1fffff) < start (49dbdf2de100000)
pcib5: (null) requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
pcib5: matched entry for 10.9.INTA
pcib5: slot 9 INTA hardwired to IRQ 28
found->	vendor=0x14e4, dev=0x1648, revid=0x10
	bus=10, slot=9, func=1
	class=02-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D3  current D0
	MSI supports 8 messages, 64 bit
	map[10]: type 1, range 64, base de110000, size 16, enabled
pcib5: memory: end (de1fffff) < start (dbfa72fdde110000)
pcib5: (null) requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
pcib5: matched entry for 10.9.INTB
pcib5: slot 9 INTB hardwired to IRQ 29
bge0: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem
0x49dbdf2de100000-0x49dbdf2de10ffff irq 28 at device 9.0 on pci10
pcib5: memory: end (de1fffff) < start (49dbdf2de100000)
pcib5: bge0 requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
bge0: couldn't map memory
device_attach: bge0 attach returned 6
bge1: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem
0xdbfa72fdde110000-0xdbfa72fdde11ffff irq 29 at device 9.1 on pci10
pcib5: memory: end (de1fffff) < start (dbfa72fdde110000)
pcib5: bge1 requested unsupported memory range 0x0-0x0 (decoding
0xde100000-0xde1fffff, 0xfff00000-0xfffff)
bge1: couldn't map memory
device_attach: bge1 attach returned 6
pci8: <base peripheral, interrupt controller> at device 11.1 (no
driver attached)


Any help you could provide would be greatly appreciated!

Thanks again,

James


On 7/16/07, Stefan Esser <se at freebsd.org> wrote:
> James Shank schrieb:
> > Greetings,
> >
> > I've run into a problem with the onboard Broadcom 5704 NetXtreme nics
> > on a Tyan S2891 Thunder K8SRE motherboard.
> >
> > Here is the relevant dmesg output to show the error:
> >
> > pcib5: <ACPI PCI-PCI bridge> at device 11.0 on pci8
> > pci10: <ACPI PCI bus> on pcib5
> > pcib5: memory: end (de1fffff) < start (48739b2de100000)
> > pcib5: memory: end (de1fffff) < start (dbca73fdde110000)
> > bge0: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem
> > 0x48739b2de100000-0x48739b2de10ffff irq 28 at device 9.0 on pci10
> > pcib5: memory: end (de1fffff) < start (48739b2de100000)
>
> Hi James,
>
> the information that you provided is not sufficient to diagnose
> this problem. You should post a *verbose* boot message log (via
> the boot loader menu or the loader command "boot -v").
>
> Please do also provide a dump of the config registers of the
> PCI bridge for which the error condition is reported:
>
> # pciconf -r pci8:11:0 0:0x3f           // device 11.0 on pci8
>
> Not sure that I'll have time to look into this right today, but
> others on the list will want the same information so you may
> want to post it there ...
>
> This looks like a problem with the PCI bridge code, not the
> device init code, actually. But just in case it is not, you
> could also provide a register dump of the Ethernet chip:
>
> # pciconf -r pci10:9:0 0:0x3f
>
> Regards, STefan
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: dmesg.boot-v.out
Type: application/octet-stream
Size: 36828 bytes
Desc: not available
Url : http://lists.freebsd.org/pipermail/freebsd-hackers/attachments/20070716/1875ef59/dmesg.boot-v.obj
-------------- next part --------------
A non-text attachment was scrubbed...
Name: pciconf-r.out
Type: application/octet-stream
Size: 708 bytes
Desc: not available
Url : http://lists.freebsd.org/pipermail/freebsd-hackers/attachments/20070716/1875ef59/pciconf-r.obj