Third IDE hard disk

[Bob Van Zant]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I don't think this question is very well suited to the -hackers list but I'll 
spam everyone anyway.

Define what you mean by FreeBSD can't find it? It doesn't find the device? Or 
you don't know how to go about "intializing" a new drive in FreeBSD? (See 
FreeBSD manual section 12.3)

What is the output of dmesg? Did it find the promise controller? Does it see 
any devices attached to it?

Here are the relevant pieces of info for my ATA-based machine:

[demon] bvanzant $ dmesg | grep ata
atapci0: <VIA 8237 SATA150 controller> port 
0x9000-0x90ff,0x9400-0x940f,0x9800-0x9803,0xa000-0xa007,0xa400-0xa403,0xa800-0xa807 
irq 10 at device 15.0 on pci0
atapci0: [MPSAFE]
ata2: at 0xa800 on atapci0
ata2: [MPSAFE]
ata3: at 0xa000 on atapci0
ata3: [MPSAFE]
atapci1: <VIA 8237 UDMA133 controller> port 0x8800-0x880f at device 15.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci1
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci1
ata1: [MPSAFE]
ad0: 26105MB <IBM-DPTA-372730> [53040/16/63] at ata0-master UDMA66
acd0: DVDROM <HITACHI DVD-ROM GD-5000> at ata1-master PIO4
ad4: 157066MB <HDS722516VLSA80> [319120/16/63] at ata2-master UDMA100
atapci0: <VIA 8237 SATA150 controller> port 
0x9000-0x90ff,0x9400-0x940f,0x9800-0x9803,0xa000-0xa007,0xa400-0xa403,0xa800-0xa807 
irq 10 at device 15.0 on pci0
atapci0: [MPSAFE]
ata2: at 0xa800 on atapci0
ata2: [MPSAFE]
ata3: at 0xa000 on atapci0
ata3: [MPSAFE]
atapci1: <VIA 8237 UDMA133 controller> port 0x8800-0x880f at device 15.1 on 
pci0
ata0: at 0x1f0 irq 14 on atapci1
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci1
ata1: [MPSAFE]
ad0: 26105MB <IBM-DPTA-372730> [53040/16/63] at ata0-master UDMA66
acd0: DVDROM <HITACHI DVD-ROM GD-5000> at ata1-master PIO4
ad4: 157066MB <HDS722516VLSA80> [319120/16/63] at ata2-master UDMA100

- -Bob


On Friday 14 May 2004 10:17 pm, Mark wrote:
> I installed my new FreeBSD 4.9R on my new ASUS KV8 Deluxe board. Everything
> work fine... except, FreeBSD cannot find the third harddisk! (the third
> IDE).
>
> How do I enable it? Or make FreeBSD see it? (please, please, let me not
> have to recompile the kernel).
>
> Thank you,
>
> - Mark
>
> _______________________________________________
> freebsd-hackers at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
> To unsubscribe, send any mail to "freebsd-hackers-unsubscribe at freebsd.org"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (FreeBSD)

iD8DBQFApQebE8j4M4/ugC4RAi+2AJ4xClDq/1q9LCIUx0J9kUjEJOODCQCgiVp4
syOIiUe8GgU0VAdfAOROROI=
=AkQf
-----END PGP SIGNATURE-----