msk0 interface stops working when downloading
Andrew Moran
amoran at forsythia.net
Fri Dec 3 06:11:23 UTC 2010
Good to know about the GB switch vs 100MB switch.
But rather than downgrade my switch, I went ahead and bought a NIC and installed it and will just ignore the onboard Marvel one until it someday works :)
--Andy
On Nov 29, 2010, at 11:03 AM, Gary Gatten wrote:
>
>
> -----Original Message-----
> From: owner-freebsd-questions at freebsd.org [mailto:owner-freebsd-questions at freebsd.org] On Behalf Of John Baldwin
> Sent: Monday, November 29, 2010 8:54 AM
> To: freebsd-current at freebsd.org
> Cc: Andrew Moran; freebsd-questions at freebsd.org
> Subject: Re: msk0 interface stops working when downloading
>
> On Tuesday, November 23, 2010 6:25:06 pm Andrew Moran wrote:
>>
>> Hey guys,
>>
>> After banging my head against this for a few hours, I've decided to ask for
> help. I installed FreeBSD 8.1 amd64 on a Shuttle J1 4100 system (tech
> specs here http://us.shuttle.com/J1_4100.aspx). I installed from DVD and the
> install went fine.
>>
>> I notice when I pkg_add -r anything, the network stops responding.
>>
>> Some details:
>>
>> 1) I can reproduce it 100% by downloading a large file. low traffic like
> the SSH connection does not trigger it. I think it's being triggered by
> traffic above a certain rate.
>> 2) I can recover by restarting the network interfaces (/etc/rc.d/netif stop;
> /etc/rc.d/netif start)
>> 3) I see no errors in dmesg or /var/log/messages. Nothing at all.
>> 4) I've tried the following in /etc/sysctl.conf:
>> net.inet.tcp.tso=0
>> net.inet.tcp.inflight.enable=0
>>
>> and in /boot/loader.conf:
>> hw.pci.enable_msix="0"
>> hw.pci.enable_msi="0"
>> hw.bce.tso_enable="0"
>>
>> But the problem persists.
>>
>> The interface is identified as:
>>
>> mskc0: <Marvell Yukon 88E8057 Gigabit Ethernet> port 0xe800-0xe8ff mem
> 0xfebfc000-0xfebfffff irq 17 at device 0.0 on pci2
>> msk0: <Marvell Technology Group Ltd. Yukon Ultra 2 Id 0xba Rev 0x00> on
> mskc0
>> msk0: Ethernet address: 80:ee:73:01:60:7d
>> miibus0: <MII bus> on msk0
>> e1000phy0: <Marvell 88E1149 Gigabit PHY> PHY 0 on miibus0
>> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
>> mskc0: [ITHREAD]
>
> When I've seen this on my netbook I did a tcpdump on another machien on the
> same hub and found that my msk0 device was spewing an endless stream of pause
> frames. I've only had this problem with a gigE switch, it works fine for me
> on a 10/100 switch.
>
> --
> John Baldwin
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"
>
>
> " When I've seen this on my netbook I did a tcpdump on another machien on the same hub and found that my msk0 device was spewing an endless stream of pause frames. "
>
> If there's an option to disable Ethernet flow control, (commonly used on Gig stuff) perhaps disabling it will prevent the unwanted "spewing". Unwaanted spewing is always bad.
>
>
>
>
>
> <font size="1">
> <div style='border:none;border-bottom:double windowtext 2.25pt;padding:0in 0in 1.0pt 0in'>
> </div>
> "This email is intended to be reviewed by only the intended recipient
> and may contain information that is privileged and/or confidential.
> If you are not the intended recipient, you are hereby notified that
> any review, use, dissemination, disclosure or copying of this email
> and its attachments, if any, is strictly prohibited. If you have
> received this email in error, please immediately notify the sender by
> return email and delete this email from your system."
> </font>
>
More information about the freebsd-current
mailing list